Land Rover Gearbox & Transferbox Parts

Taper Roller Bearing - shaft bearing for the R380 five-speed manual gearbox. A taper roller bearing carries both radial load and axial thrust, loc...

lock washer. sold EACH.

Bolt is an M8 x 80 mm threaded fastener used to clamp two components together at a bolted joint. It is tightened into a threaded hole or secured w...

Nut - M8 plain low-profile nut, sold individually. A standard metric M8 nut in the low-profile (thin) form. Used across gearbox, suspension, axle,...

Kickdown Cable Assembly for the automatic transmission control. The cable links the throttle to the automatic gearbox, relaying throttle position s...

Seat yoke

Gearbox Gasket seals the top cover to the main casing of the LT77 five-speed manual gearbox, forming an oil-tight joint between the top cover plate...

Front Cover Bolt - M10 flanged hex bolt used to secure the engine front (timing) cover. It also serves as a general-purpose fixing at engine and dr...

Flange Bolt is an M8 x 35 mm bolt with an integral flange beneath the head. The flange spreads clamp load across the joint face and acts as a buil...

Transmission Brake Drum for the transmission (hand) brake. Mounts to the transfer box rear output flange and houses the transmission brake shoes, ...

Transfer Box Lever Lock Nut used to secure the selector linkage at the transfer case. This half nut (thin profile locking nut) threads onto the sel...

Mainshaft Taper Roller Bearing supports the mainshaft at the 5th/reverse end of the R380 (and LT77) 5-speed manual gearbox. It carries the mainsha...

Transfer Box Output Shaft Mud Shield fitted at the output shaft oil seal of the LT230 transfer box. The shield sits over the output shaft ahead of...

Transfer Box Sealing Ring - Locking Pin A rubber O-ring that seals the locking pin where it enters the transfer box case. It seals the selector lo...

Heater Hose for the 200TDi engine cooling and heating circuit. This hose routes coolant from the engine cooling system to the cabin heater matrix,...

Mainshaft 5th Speed Gear for the LT77 and LT77S 5-speed manual gearbox. This gear is mounted on the mainshaft assembly and meshes with the corresp...

Countersunk Screw for the Transmission Brake Assembly. The countersunk head sits flush within the mating surface, maintaining correct alignment and...

Circlip - Output Shaft Flange used within the transfer box output flange assembly to retain the output shaft bearing and associated components in p...

Joint Washer - LT77 Front Cover seals the mating face between the front cover and the main casing of the LT77 5-speed manual gearbox. The washer p...

Magnetic Sump Plug for the ZF 4-speed automatic transmission. This drain plug seals the transmission oil pan at the drain point. Its magnetic tip ...

Gearbox Side Cover Gasket for the LT95 4-speed V8 gearbox. This gasket seals the side cover to the gearbox casing, preventing oil leaks from the ge...

Gear Lever Damper for the LT95 four-speed gearbox gear-change mechanism. This damping washer fits at the base of the main gear lever, absorbing vi...

Mainshaft Bearing supports the mainshaft within the LT230 transfer box, carrying the shaft's rotational loads and keeping it running true as drive ...

O-Ring is a sealing ring used within the ZF 4-speed automatic gearbox and the LT230 transfer box. This O-ring seals fluid passages or housing inte...

Needle Bearing is an internal roller bearing used within the LT77 5-speed and R380 5-speed manual gearbox assemblies. Needle roller bearings of th...

Baulk Ring for the R380 5-speed manual gearbox synchromesh assembly. The baulk ring (also known as the synchromesh ring) is the friction cone elem...

O-Ring - Diff Lock - LT230 provides the hydraulic seal at the differential lock mechanism and front output shaft location within the LT230 transfer...

Automatic Transmission Oil Screen for the ZF 4-speed automatic transmission, fitted within the transmission oil sump. The screen filters the autom...

Gearbox Mounting - left-hand transmission rubber mounting for the 2.5L 300 TDi diesel. This rubber-to-metal mounting supports the gearbox on the l...

Gearbox Gaiter Grommet seals the point where the high/low transfer lever passes through its gaiter on the LT95 four-speed gearbox. Fitted to the t...

Release Bearing Guide - the guide sleeve in the clutch release mechanism, mounted on the front cover of the manual gearbox. It encircles the gearb...

Yoke Transmission

Oil Seal Collar for the R380 manual gearbox. The collar fits over the output shaft and provides the hardened running surface against which the gea...

Layshaft Bearing for the R380 five-speed manual gearbox. This taper roller bearing supports the layshaft (countershaft) within the gearbox casing, ...

Oil Pump Repair Kit - renews the oil pump of the LT77 and LT85 five-speed manual gearbox. The pump is housed in the gearbox extension casing and ci...

Thrust Washer and Pin for the LT95 four-speed gearbox, 3.55mm thickness. This selective-thickness washer, with its locating pin, sets the end-float...

Selector Fork for the 3rd and 4th gear positions in the five-speed manual gearbox (LT77 and R380). The fork engages the 3rd/4th synchro hub sleeve...

Gearchange Spring for the LT77 five-speed manual gearbox, fitted within the gearchange and lever assembly. The spring acts on the gear lever mecha...

Gearbox Selector Pad for the LT77 five-speed manual gearbox. Fits the 5th gear selector within the selector and yoke assembly, forming the bearing...

Front Cover to Gearcase Gasket seals the joint between the front cover and the main gearcase on the LT77 5-speed manual gearbox. This gasket preve...

Gearbox Sump Gasket for the ZF 4-speed automatic transmission, sealing the joint between the transmission oil pan (sump) and the gearbox casing. T...

Gearbox Mainshaft Oil Seal, fitted where the mainshaft passes through the gearbox casing on the 5-speed manual transmission. It runs against the r...

Needle Roller Bearing for the R380 manual gearbox. It carries the reverse idler on the layshaft, allowing the gear to rotate with minimal friction ...

Baulk Ring for the LT77 5-speed manual gearbox synchromesh assembly. The baulk ring is the friction cone element of the synchromesh unit. It conta...

5th Gear - LT77 is the mainshaft-mounted overdrive gear for the LT77 5-speed manual gearbox, located at the rear of the transmission in the 5th-gea...

Gearbox Breather for the gearbox and transfer case assembly. This breather is located on the gearbox or transfer case casing and vents internal pr...

3rd Speed Mainshaft Gear - LT95 4-Speed Gearbox This is the 3rd speed driven gear on the mainshaft of the LT95 unit-construction 4-speed gearbox. ...

Screw - M8 x 25mm is a fastener used in the assembly of the LT230 transfer gearbox. The LT230 is a two-speed transfer box fitted to Defender, Disc...