Land Rover Interior Parts

Seat Belt - Rear Centre Lap - Long End for the rear seat belt assembly in the Defender passenger compartment. This is the long webbing end of the ...

Seat Back - Inner - the centre backrest of the three-piece front bench seat, trimmed in black vinyl. Fitted between the two outer seat backs, it p...

Grab Handle in black, an interior assist handle that mounts to the roof trim rail. It provides occupants with a secure handhold when entering or e...

Keep your Land Rover Defender clean and protected with this Rubber Mat Set designed specifically for LT77/R380 gearboxes in Defender models from XA...

Locking Nut - a push-on locking nut for securing interior trim and ducting. It pushes onto a stud or screw thread and grips to hold the fixing cap...

Blanking Plug fills an unused switch aperture in the dashboard switch panel. Where a fascia switch position is not fitted, this plug closes off th...

Front Outer Seat Cushion Base for the adjustable seat frame in Series II, IIA, and III 109" long-wheelbase vehicles. This is the outer seat base c...

The Seat Spring Rear Outrigger is a key component designed for the Defender 110/130 models. This high-quality rear seat spring outrigger supports t...

Rear Door Finisher for the internal rear door release assembly. This trim panel finisher fits around the interior door release mechanism on the re...

Radio Cassette Housing for the Defender 90/110 dashboard interior trim assembly. This moulded trim housing surrounds and retains the radio cassett...

Carpet Set - front cab area, for 2.4L Puma TDCi models in right-hand drive configuration. The set covers the bulkhead, gearbox tunnel, under-dash ...

Cubby Box Black Mesh - Series 3 - Defender

Heated Sport Seats (Pair) - a matched pair of front bucket-style sports seats for the cab, finished in black with a diamond-pattern facing and a lo...

Sport Seats - a pair of low-base front bucket seats finished in black vinyl with a diamond-pattern facing. The sports design pairs a shaped, suppo...

Cubby Box Hinge in brass, forming the pivot point for the centre console cubby box lid. The hinge fixes the lid to the cubby box body, carrying th...

Seat Base Cushion - Front for the front seat assembly. This cushion forms the lower seating surface and mounts onto the front seat frame, supporti...

Door Trim - Rear Casing - Slate Grey for the Defender rear end door interior. This rear door casing panel fits the interior face of the Defender r...

Spring Clip for the rear end door trim casing, part of the interior trim fixings. The sprung clip retains the rear door card (trim casing) to the ...

Seat Frame for the adjustable driver's seat on Series II and Series III models. This structural frame forms the base of the driver's seat assembly.

Front Door Card is the interior trim panel that covers the inner structure of the front door, concealing the window regulator, latch linkage and wi...

Rear Inward-Facing Seat in black trim. This individual inward-facing seat mounts in the load area to provide additional occasional seating. Inward...

Seat Belt Fixing Kit provides the mounting hardware used to secure a seat belt assembly to the vehicle body anchorage points. The kit supplies the...

Seat Recline Mechanism Cover - RH is the trim cover plate fitted over the front seat recline adjuster mechanism. It conceals and protects the recl...

Seatbelt Anchorage - Upper - LH for the Defender seatbelt system. This structural bracket mounts to the pillar or roof structure at the top of the...

Seatbelt Anchorage - Upper - RH for the Defender seatbelt system. This structural bracket mounts to the pillar or roof structure at the top of the...

Outer Door Handle Cover is the right-hand exterior finger pull fitted to the top of the door, part of the sliding side-window door top assembly. I...

Floor Mat for the second-row (rear) floor area. It is shaped to fit the rear passenger footwell and protects the vehicle's carpet from mud, moistur...

Seat Heater Kit (Retrofit, Pair) adds heating to two seats by fitting flexible heating elements between the seat upholstery and the seat cover, acr...

Load Bay Liner Kit lines the rear load area to protect the original bed and inner surfaces from cargo abrasion, impact and moisture. The liner is f...

Rubber mat set 110 2nd row

Pedal Shaft is the transverse shaft on which both the clutch pedal and brake pedal are mounted within the cab, on vehicles without a brake servo. ...

Rubber Floor Mat Set - Front for the front footwells, supplied as a matching pair. The mats are moulded in rubber to protect the front floor area a...

Roof Centre Console for the Defender Hard Top and Station Wagon interior headlining. The console features a single DIN radio aperture with removab...

Waterproof Front Seat Covers for Defender (2007-2016, Puma), in black. This pair of seat covers is designed for the front seats of the Puma-era De...

Seat Outer Base - Grey is the lower seating surface unit for the outboard seat position on the Defender, trimmed in grey vinyl. The base mounts to...

Seat Back - Outer - Standard - Black for the left and right outer positions of the three-abreast front bench seat in Land Rover Series vehicles. T...

Seat Back - Inner - Standard - Black for the centre position of the three-abreast front bench seat in Land Rover Series vehicles. This vinyl seat ...

Seat Back and Headrest for the outer front seat, in the deluxe pattern and finished in black. This is the upholstered backrest (squab) the occupant...

Seat Re-trim Kit (Outer Seat, Grey) re-covers an outer seat, renewing the cushion and squab foams together with their outer covers to restore the s...

Seat Re-trim Kit refurbishes one complete front outer seat in a Techno vinyl finish and is supplied without adhesive spray. The kit rebuilds both ...

Inner Seat Base is the centre front seat base cushion, forming the lower seating platform of the basic vinyl front seat. Finished in black vinyl f...

Trim Clip, male half, used in the facia and dash trim assembly. The clip is the male part of a two-piece push-fit fastener. It locates in the trim...

Fuse Box Cover - Facia is the moulded cover that closes off the facia-mounted fuse box, concealing the fuse and relay positions behind the dash. I...

Rear Door Casing - the interior trim panel that lines the inner face of the rear end door. It covers the door's inner structure to give a finished...

Centre Cubby Box - Techno finish. A console box that mounts on the transmission tunnel between the front seats, providing enclosed central storage ...

Rear Seat Frame Fastener - retaining fastener for the rear seat frame mounting in the load area. Secures the rear row seat frame assembly to its b...

Removable Seat Mounting Kit for installing a Sparco R100 sports recliner seat. The removable design lets the seat be lifted out without tools, givi...

Door Trim Casing - front door, lower section, right hand side, black finish. Forms the lower part of the front door interior trim, covering the in...