Land Rover Interior Parts

Drive Pin Fastener is a two-piece push-in fixing used to retain interior trim and ducting panels. The fastener body is pushed through aligned hole...

Centre Cubby Box finished in black vinyl, fitting the centre position between the front seats to provide an enclosed storage compartment with a mou...

Fir Tree Fastener secures interior body and roof trim panels to the vehicle structure. The ribbed, tapered fir-tree shank pushes into a panel hole...

Heater Control Finger Grip The finger grip fitted to a heater control slider on the heater (HVAC) control panel, operated in the up/down plane. It...

Accelerator Pedal Return Spring for the cable-operated throttle linkage. The spring returns the accelerator pedal to its rest position when foot p...

Bolt, a hexagon-head fastener with a 5/16" UNF thread, 7/8" long. This imperial fastener is of the UNF (Unified National Fine) thread series and i...

Heater Control Finger Grip The finger grip fitted to the hot/cold (temperature) control on the heater control panel. It clips onto the control lev...

Steering Wheel Boss in the steering column assembly, providing the mounting interface between the column shaft and the steering wheel. The 48-spli...

Hex-head bolt, 5/16" UNF thread, 3/4" long. Unified Fine (UNF) thread form with a hexagonal head for use with standard imperial spanners and socke...

Seat Belt Buckle - Right-Hand - the latching receptacle of the seat belt restraint, into which the belt tongue (latch plate) engages and locks to h...

Bolt 1/4" UNF x 2" is a hex-head set bolt with a 1/4-inch Unified National Fine (UNF) thread at 28 threads per inch and a 2-inch shank length. It ...

Hex-head screw, 5/16" UNF thread, 1-1/4" long. Unified Fine (UNF) thread form with a hexagonal head for use with standard imperial spanners and so...

Seat Squab Bolt - shouldered bolt for mounting the seat squab (backrest) to its frame. This shouldered bolt secures the seat squab at its mounting...

Countersunk Screw - a machine screw with a flat, cone-shaped head that seats flush with the surface it fixes, leaving no proud edge. Metric M6 thr...

Transfer Gear Knob - High/Low - LT95 is the hand grip fitted to the high/low range transfer lever on the LT95 gearbox. It threads onto the top of ...

Interior Mirror Bracket mounts the interior rear-view mirror to the body, providing the fixing point for the mirror stem. This is the untrimmed ve...

Split Pin - a 1.5mm x 12mm cotter pin used to lock a slotted (castle) nut or to retain a clevis pin. Passed through a drilled cross-hole in the sh...

Size/Diameter: 1/4" unf x 7/8"

Steering Wheel - a 14-inch three-spoke replacement wheel with a black vinyl rim and black centre. The wheel mounts to the steering column through ...

Seat Belt - 3-Point Inertia Reel is a lap-and-diagonal front seat belt assembly with a self-locking inertia reel, supplied to the basic Type A spec...

Static Lap Seat Belt for the second-row seating position, forming part of the interior occupant restraint system. The non-retractable, fixed-lengt...

Centre Squab Buffer - a rubber buffer that cushions the centre seat squab (backrest) against the surrounding bodywork. It prevents metal-to-metal ...

Seat Belt Buckle Catch - left-hand front seat belt stalk receiver forming the fixed lower end of the front LH seat belt assembly. The non-audible c...

Self-Tapping Screw – No. 6 × 3/4 in used to secure interior trim and panel fixings, such as the dash panel and upper fascia mouldings. Being self-...

Heater Duct, left-hand side, within the heater air distribution system. Routes air from the heater assembly to the floor-level outlet beneath the ...

Nut - 10/32" UNF A nut with a #10-32 UNF (Unified National Fine) internal thread, run onto a matching UNF bolt or stud to clamp the joint.

Hex Head Bolt - 1/4" UNF thread, 5/8" long, with a hexagonal head. A general-purpose imperial fastener with a Unified Fine (UNF) thread form, driv...

Steering Wheel is a 15-inch three-spoke replacement wheel that mounts to the steering column. It is supplied without a boss, so a separate fitting...

Fuel Gauge is a 12V dash-mounted instrument that displays the amount of fuel remaining in the tank. Fitted within the instrument panel, it receive...

Strap Stud is a body fixing used in the canvas hood (soft top) and hood frame assembly. It provides an anchor point over which a retaining strap i...

Keep your Land Rovers interior clean and tidy with a loadspace mat. Ribbed rubber / 1,560 x 920 x 3mm Defender 110 - excluded 3 door commercial ...

Static Three-Point Seat Belt for the front seating position, combining a lap strap and a diagonal shoulder strap in a single restraint. This is a ...

Seat Belt Bracket for the front seat belt, lower mounting, right-hand side. This bracket bolts to the seat box and provides the lower anchorage po...

Blanking Plug for the instrument panel, fitted to close an unused aperture in the dashboard where an instrument, switch or gauge is not installed. ...

Centre Cubby Box finished in grey, fitting the centre position between the front seats to provide an enclosed storage compartment with a moulded do...

Screw - 2BA x 1" is a round head screw in British Association (BA) thread form, 2BA size, 1 inch in length. Used throughout the Series Land Rover ...

Countersunk Screw - a machine screw with a flat, cone-shaped head that seats flush with the surface it fixes, leaving no proud edge. Metric M6 thr...

Plastic Washer serves as a spacing and anti-friction washer at the front seat hinge and the rear door check arm pivot. Fitted at the pivot joint, ...

Pan Head Screw - a 2BA x 1/2 inch slotted pan head fastener used across interior trim and body panel fixings. It retains interior trim panels and ...

Safari Rear Side Door Top Panel (r/H) - Black Vinyl

Transfer Gear Knob - High/Low - LT95 is the hand grip fitted to the high/low range transfer lever on the LT95 gearbox. It threads onto the top of ...