Land Rover Interior Parts

Heater Duct, left-hand side, within the heater air distribution system. Routes air from the heater assembly to the floor-level outlet beneath the ...

Nut - 10/32" UNF A nut with a #10-32 UNF (Unified National Fine) internal thread, run onto a matching UNF bolt or stud to clamp the joint.

Hex Head Bolt - 1/4" UNF thread, 5/8" long, with a hexagonal head. A general-purpose imperial fastener with a Unified Fine (UNF) thread form, driv...

Clip Nut spring-steel fastener that provides a captive threaded fixing point on panels and brackets. The nut clips over the edge of a panel or sli...

Interior Trim Fastener - a grey drive-in fastener for securing interior trim panels in the cabin. It retains facia and carpet trim, the cubby box,...

Nylon Stud, a trim retaining fastener used to hold interior trim panels and carpet in position. The stud pushes into a pilot hole in the body pane...

Interior Trim Retainer Clip - a moulded fastener used to secure interior trim to the vehicle body. The clip retains door casings, pillar trims and...

Screw - a self-tapping pan-head fastener used in interior trim assembly. It cuts its own thread into the panel or moulded mounting boss to secure ...

Aluminium Pop Rivet, a blind rivet used as a general fixing for body panels, interior trim and seat-mounting brackets. It is set with a rivet gun: ...

Self-Tapping Screw - Black is an M8 x 25mm self-tapping screw with a black finish. The self-tapping thread cuts its own mating thread as it is dri...

Steering Wheel is a 15-inch three-spoke replacement wheel that mounts to the steering column. It is supplied without a boss, so a separate fitting...

Pull Ring for the rear seat lock release. It operates the split rear seat lock mechanism, releasing the seat squab so the backrest can be folded d...

Seat Belt is the front right-hand inertia-reel seat belt assembly. It comprises the retractor, webbing and buckle tongue for the front right-hand ...

Cap bolt

Fuel Gauge is a 12V dash-mounted instrument that displays the amount of fuel remaining in the tank. Fitted within the instrument panel, it receive...

Sac Snap Clip

Heated Seat Element Assembly for the front seat squab (the backrest), part of the seat heating circuit. The heating pad sits behind the squab trim...

Trim Pad Clip is a fastening clip used to secure interior trim pads to the bodyside and door structure. It locates into a pre-formed hole in the p...

Interior Trim Fastener in Bahama Beige, for securing rear interior trim panels in seven-seat Discovery 1 variants. This plastic push-in fastener c...

Fir Tree Fastener is a push-fit trim clip that retains roof insulation against the vehicle body. Its ribbed fir-tree shank pushes into a pre-forme...

Bolt - M8 x 40mm standard metric hex-head fastener for use across engine, gearbox, body, and chassis assembly applications.

Strap Stud is a body fixing used in the canvas hood (soft top) and hood frame assembly. It provides an anchor point over which a retaining strap i...

Keep your Land Rovers interior clean and tidy with a loadspace mat. Ribbed rubber / 1,560 x 920 x 3mm Defender 110 - excluded 3 door commercial ...

Screw - a No. 6 x 1" self-tapping screw used to secure interior and body trim. It fixes A-pillar trim, roof trim and body trim panels, forming its...

Spire Nut is a spring-steel push-on clip fastener that provides a threaded anchor in thin sheet metal. The nut pushes over a hole in a panel and r...

Drive Screw is a countersunk-head self-tapping screw used to secure body and interior trim components. The self-tapping thread cuts its own mating...

CV boot gaiter kit D3, D4, RRsp

Seat Base Cover for a front outer seat, forming the trim over the seat base cushion. Finished in black vinyl. The cover fits over the front outer ...

Static Three-Point Seat Belt for the front seating position, combining a lap strap and a diagonal shoulder strap in a single restraint. This is a ...

Seat Belt Bracket for the front seat belt, lower mounting, right-hand side. This bracket bolts to the seat box and provides the lower anchorage po...

Steering Wheel Boss is a hub adapter that mounts a replacement steering wheel to the steering column. It engages a 36-spline column shaft and form...

Upgrade or replace your steering wheel boss with this high-quality 36-tooth adapter, designed specifically for Land Rover Defender to 1991 90/110 v...

Luggage Tie-Down Hook - anchor hook in the luggage compartment for securing loads, integrated with the side trim retainer. Located in the luggage ...

Front Seat Belt, Right-Hand for the front right-hand seating position. It forms part of the vehicle's occupant restraint system. The assembly is a...

Front Door Card is the interior trim panel that covers the inner structure of the front door, concealing the window regulator, latch linkage and wi...

Door Casing Trim Clip is a fir-tree push-fit fastener used in the interior door trim assembly to retain the door casing panel against the door fram...

Blanking Plug for the instrument panel, fitted to close an unused aperture in the dashboard where an instrument, switch or gauge is not installed. ...

Electric Seat Switch for the right-hand seat cushion adjustment, part of the powered seat control assembly. Mounted in the seat base side trim, it...

Screw for body and interior trim fixing - a No.12 x 1/2" pan-head screw. Used to secure body panels, dash and facia, wheelarch and interior trim. ...

Door Card - Push Button - Electric - LH is a left-hand interior door trim panel incorporating a push-button door release and electric window switch...

Rear Trim Panels Without Windows - moulded interior side trim panels for the rear compartment, supplied as a matched left and right pair. The pane...

Door Card - Push Button - Electric - RH is the interior trim panel for the right-hand front door. It covers the inner door frame to provide the fi...

Centre Cubby Box finished in grey, fitting the centre position between the front seats to provide an enclosed storage compartment with a moulded do...

Nutsert, M8 blind rivet nut for use where a permanent threaded insert is required and access to the reverse face of the panel or bracket is not pos...

Front Air Grille covers the fresh air intake at the base of the windscreen, forming part of the fresh air system that feeds the heater and ventilat...

Screw - 2BA x 1" is a round head screw in British Association (BA) thread form, 2BA size, 1 inch in length. Used throughout the Series Land Rover ...

Self-Tapping Screw - a No. 14 x 3/4" black button-head self-tapping drive screw used across body and interior trim. It secures the front grille to...