Land Rover Series 1 Parts

Grommet

Brake Pipe Union for the hydraulic brake system, a female fitting in brass. This union connects a 3/16 inch brake pipe into the brake hydraulic ci...

Oil Filler Plug serving as the combined fill and level check point for the swivel pin housing, manual gearbox gearcase, and LT230 transfer box on L...

Rear brake drum installed in the rear drum brake assembly of the vehicle braking system. The drum mounts to the rear hub and rotates with the wheel...

Axle Key Washer for the hub nut locking system in the axle assembly. This tab washer seats beneath the axle hub nut, with tabs that locate into ma...

Gear Lever Knob threads onto the top of the main gearbox gear lever to form the hand grip used for gear selection. It gives the driver a defined c...

Axle Bump Stop - rubber bump stop for the front and rear suspension axle assemblies. Fitted to the chassis above each axle, the bump stop limits a...

Front Brake Shoe Spring for the front drum brake assembly. This return spring connects the two brake shoes and pulls them back off the drum when th...

Oil seal

Bonnet Canvas Rest Strip for the front body assembly. This canvas strip mounts across the top of the radiator/front panel, forming the surface the ...

Accelerator Spring for the throttle linkage on diesel engines. This return spring acts on the accelerator linkage, drawing the throttle back to th...

Wheel Cylinder Overhaul Kit for front drum brake systems fitted with 11-inch brake drums. This kit provides the necessary parts to overhaul all fo...

Anti-Roll Bar Washer used at the anti-roll bar and shock absorber mounting. The washer spreads the clamping load of the retaining nut across the m...

Output Shaft Oil Seal seals the front or rear output shaft of the LT76 transfer gearbox, retaining lubricant within the transfer case and preventin...

Cable Clip for securing the body wiring harness, part of the vehicle electrical system. This clip retains a cable run against the body or chassis,...

Lock Plate for the front axle assembly. This metal tab washer locks fastener heads in position by bending a tab against the bolt head or nut after...

Copper Sealing Washer used across a wide range of sealing applications on Land Rover vehicles. This soft copper washer provides a reliable, leak-f...

Wheel Spanner with a 27 mm socket, a hand tool for removing and refitting wheel nuts. Engages the 27 mm hexagon of the wheel nut to loosen or tigh...

Side Cover Gasket sealing the cylinder-block side cover (tappet inspection cover) to the block face, for petrol and diesel engines. The side cover...

Wheel Cylinder for the rear drum brake assembly, left-hand side. The wheel cylinder forms part of the hydraulic drum brake circuit, converting hyd...

Oil Filter for the engine lubrication system, suited to the 2.0L and 2.6L IOE (inlet-over-exhaust) petrol engines. The filter traps metallic parti...

Detent Spring for the manual gearbox gear selector mechanism. The spring loads the detent ball against the selector shaft, holding the selected ge...

CuNiFer Brake Pipe, 3/16" outer diameter, supplied for the brake hydraulic circuit. The copper-nickel alloy resists corrosion and is soft enough to...

Accelerator Cable links the accelerator pedal to the injection pump throttle lever, forming part of the throttle linkage on the 2.25L diesel engine...

Fuel Pump Gasket for the 2.0L diesel engine (Series II) and 2.25L diesel engine (Series IIA). This gasket seals between the mechanical fuel pump b...

7" round LED headlamp 12/24V black 78W LHD (pair)

Alternator - charging unit in the vehicle's electrical charging system. Driven from the engine by the accessory belt, it generates current to powe...

Shock Absorber for the front suspension on the short-wheelbase (SWB) chassis. Mounted between the front axle and the chassis, the hydraulic damper...

Gearbox Plug Sealing Washer for LT76 and LT77 manual gearbox drain, level, and inspection plugs. This sealing washer fits beneath the thread of ge...

Track Rod Clamp is a split-tube collar that secures the threaded track rod end into the track rod tube on the front steering axle. Once the front ...

Transfer Lever Knob in red, for the high/low range selector on the transfer gearbox. It threads onto the top of the transfer change lever and prov...

Exterior Mirror - Round Arm is a complete wing mirror assembly comprising a round convex mirror head and a standard-length mounting arm, designed f...

Steering Relay Assembly within the steering linkage. The relay transfers steering movement from the steering box drop arm to the drag link, passin...

Restore your Series or Defender Land Rover's door with this door bottom repair section. This replacement piece is designed to repair damaged or rus...

Wheel Cylinder for the rear drum brake assembly, left-hand side. The wheel cylinder forms part of the hydraulic drum brake circuit, converting hyd...

Window Channel - Top is the upper glass-run channel that guides the top edge of the window glass, supplied as a 94 cm length. It forms the running...

Thermostat for the engine cooling system, with an 82°C opening temperature. The thermostat regulates coolant flow between the engine and the radia...

Wind Deflector Set - a pair of stick-on air deflectors for the front door windows. Each deflector fits to the outer edge of the door window frame ...

Seat Base - Outer is the lower seat cushion for either outer (driver or passenger) position in the front seating assembly. Foam-padded and finishe...

Flywheel Housing O-Ring - a sealing ring at the rear of the engine where the flywheel housing meets the cylinder block. Fitted to the 2.25L engine...

Wheel Cylinder for the rear drum brake assembly, right-hand side. The wheel cylinder forms part of the hydraulic drum brake circuit, converting hy...

Swivel Ball Seal Retainer for the front axle swivel housing. This retaining ring clamps the swivel housing oil seal against the swivel ball, holdi...

Speedometer Pinion Oil Seal for the gearbox speedometer drive take-off. It seals around the speedometer drive pinion where it enters the gearbox ho...

Speedometer Cable Plate Screw secures the speedometer cable retaining plate to the gearbox. It clamps the plate that holds the speedometer drive c...

Bonnet Spring Retaining Clip, part of the bonnet hinge and stay assembly. Retains the bonnet (hood) tension spring against its anchor, holding the...

Differential flange 4-spline

Starting Handle for manual cranking of the engine. The handle engages the dog on the front of the crankshaft, allowing the crankshaft to be turned...

Propshaft Bolt Kit - Rear is a driveline fixing set for securing the rear propeller shaft at its flange connections. The kit provides the correct-...