Land Rover Series 1 Parts

Hex Nut with a 5/16" UNF (Unified National Fine) thread. This six-sided fastener threads onto a matching 5/16" UNF bolt or stud and is tightened w...

Transfer Box Lever Lock Nut used to secure the selector linkage at the transfer case. This half nut (thin profile locking nut) threads onto the sel...

4-Leaf Parabolic Rear Spring Pair for the rear suspension of Series long-wheelbase Land Rovers. Parabolic leaf springs use a progressive, variable...

Steel Road Wheel is a welded steel road wheel with a 6.5 x 16 inch rim, finished in black with a Wolf-style profile for road use with tubeless tyre...

Clutch Slave Cylinder Bleed Screw for the hydraulic clutch release circuit. It threads into the clutch slave cylinder, at the highest point of the ...

Wheel Nut, Flat Type secures the road wheel to the hub studs. It has a flat, single-chamfer seating face and a 27mm hexagon.

Exhaust Silencer for right-hand-drive applications. Part of the exhaust system, this silencer attenuates combustion noise as the gases pass throug...

In/out member spring

Shim plate

Barrel Lock and Key for the door lock, supplied as the keyed lock barrel together with a matching key. The barrel is the cylinder the key turns to...

Transfer Box Output Mud Shield Shield that fits over the transfer box output flange to protect the output shaft oil seal from mud, water and debris...

Timing Chain Idler Wheel runs against the timing chain within the front timing case, guiding the chain and helping maintain its tension between the...

Nut is a hexagonal nut cut with a 7/16" BSF (British Standard Fine) thread. It threads onto a matching 7/16" BSF bolt or stud to secure a bolted j...

Leather hasp civilian

Oil Seal - Clutch Cross Shaft for Series 1 and Series 2 Land Rover vehicles (1948-1971). The clutch cross shaft passes through the bellhousing and...

Contact Set - Lucas Distributor is the breaker-point set for the ignition distributor. Mounted on the distributor baseplate, the points are opened...

Outer Distance Piece for the front axle swivel pin housing. The distance piece is a spacer that sets the position of the swivel pin bearing within...

Exhaust Hanger Plate - a flexi-mount bracket within the exhaust system mounting hardware. It suspends the exhaust from the vehicle underframe, its...

Gear Selector Plunger is the interlocker pin fitted to the 1st and 2nd gear selector shaft in the gearbox top cover. It prevents simultaneous selec...

Door Clevis Pin for the door check strap mechanism. The pin locates the check strap to its mounting bracket, forming the pivot the strap works aga...

Shackle Pin

Steering Drag Link - With Bracket - 73cm is a steering linkage rod, supplied with an integrated steering damper bracket. The drag link transmits s...

Cleat Rope Hook Body Side All and Classic (Softtop) - Series Defender

Spring Washer, M8, a split ring washer used with M8 bolts and nuts to prevent fastener loosening caused by vibration and cyclical loading. The spl...

Plain Washer M8

Camshaft Bearing for the 2nd, 3rd and 4th journal positions of the four-cylinder engine. The bearing shell is fitted into its housing in the cylind...

Gearbox Gasket for the LT76 four-speed gearbox with integral transfer assembly. It seals a mating housing face within the gearbox and transfer cas...

Round Mirror Head is the circular exterior mirror glass and housing that mounts on a wing- or fender-mounted mirror arm. It gives the driver a rea...

Clutch Plate is the friction-lined driven plate of the clutch assembly, 9 inch (229 mm) diameter. Its splined hub engages the gearbox input shaft ...

Fixed Towing Drop Plate bolts to the rear tow bar to carry the towball at the correct towing height. The plate is a fixed, non-adjustable type set...

Locating Dowel for the flywheel-to-crankshaft joint, part of the crankshaft and flywheel assembly. Pressed into the crankshaft rear flange, the do...

Window Channel - Vertical - the upright glass run for the Truck Cab side window, part of the door glazing assembly. It lines the vertical edge of ...

Floor Mounting Pad is a 5mm rubber spacer pad used at the rear body floor support mounting, fitted between the body and the chassis-mounted support...

Handbrake Drum is the drum for the transmission-mounted parking brake, for use with the LT76 gearbox. Mounted at the rear of the gearbox on the tr...

Thrust Washer for the 2nd gear assembly within the manual gearbox. Fitted to the mainshaft to control the end float of 2nd gear, the washer is sel...

Domed Nut with a 5/16 UNF thread, a finishing fastener. The domed (acorn) form encloses the end of the stud or bolt it threads onto, protecting th...

Oil Pump Lock Tab, part of the engine oil pump assembly. The lock tab is a tab washer fitted under the oil pump retaining fastener; once the faste...

Exhaust Connecting Pipe is the intermediate section of the exhaust system for Series short wheelbase vehicles fitted with the 2.25L diesel engine, ...

Front Spring Dowel for the 9-leaf front road spring, part of the leaf spring suspension assembly. The dowel is the centre locating pin that passes...

Swivel Bearing - the bearing on which the front axle swivel pin housing pivots, within the steering swivel assembly. It locates the swivel pin in ...

Track Rod End Boot Ring - spring retaining ring for the track rod end of the steering linkage. It clamps the rubber dust boot onto the track rod en...

Sump Gasket seals the joint between the oil sump and the cylinder block within the engine lubrication system, preventing oil leakage at the sump fl...

Headlamp Bowl Kit - Series

Shock Absorber Bush Set for the shock absorber mountings. This set provides the bushes that locate each shock absorber at its mounting eyes, insul...

Shock Absorber for the front suspension on the short-wheelbase (SWB) chassis. Mounted between the front axle and the chassis, the hydraulic damper...

Hex Nut - M8 is a standard six-sided metric threaded fastener with an 8 mm nominal thread diameter. It threads onto a matching M8 bolt or stud to ...

Headlamp Bowl Seal - the gasket that seals the 7-inch headlamp bowl against the surrounding body panel. Fitted around the lamp aperture, it closes...

Bulkhead Repair Panel with Vents - Right-Hand is a weld-in repair section for the upper corner of the bulkhead, incorporating the fresh-air vent su...