Land Rover Series 1 Parts

Clutch Withdrawal Tube fitted in the clutch cross-shaft withdrawal mechanism on Series II, IIA, and III Land Rovers. This tube forms the connectin...

Fuel Pipe Sealing Washer seals the fuel pipe union at the DPA diesel injection pump. Fitted at the union connection, it is compressed between the ...

Bolt - 5/16 inch BSF x 1 inch for the gearbox selector assembly. Used to secure the gear selector forks to their respective selector shafts within...

Rear Spring Hanger is a chassis mounting bracket in the rear leaf-spring suspension, forming the forward anchor point that carries the front eye of...

Interior Lamp - courtesy lamp for the passenger compartment. Provides interior illumination as part of the interior lighting circuit, typically sw...

Nut - 2BA, a small-diameter fastener in the British Association (BA) thread standard. 2BA refers to the No.2 size within the British Association t...

Shock Absorber - Oil Filled - Front for the front suspension assembly on Series I, II, and IIA Land Rovers. This oil-filled hydraulic unit mounts ...

Dynamo Brush Set for the Lucas C40 dynamo. The carbon brushes bear against the commutator to conduct current through the rotating armature windings...

Gear Lever for the main gearbox, right-hand drive configuration. The gear lever is the primary driver interface in the gearbox change mechanism, t...

Tappet Slide for Land Rover 4-cylinder engines, covering the Series I, Series II, Series IIA, and Series III (2.0L Diesel and 2.25L Petrol and Dies...

Rear Fog Lamp for the rear lighting circuit, providing the high-intensity red rear light used to make the vehicle conspicuous from behind in poor v...

Camshaft Bearing Set comprises the plain bearing shells that support the camshaft within the cylinder block of the four-cylinder engine. The beari...

Gearbox Thrust Washer

Drive Screw with a round head, a general body and chassis fixing. The steep-helix thread lets the screw be driven into a pre-drilled hole with a h...

Clutch Cover is the pressure plate assembly of the clutch, 9 inch (229 mm) diameter, coil-spring type with three release fingers. It bolts to the ...

Bronze Distance Piece Mainshaft 1954-71

Front Exhaust Pipe forms the front section of the exhaust system, mounting to the exhaust manifold by a four-stud flange. It carries exhaust gas f...

Steering Relay Shaft Bush - Split Half for the steering relay assembly on classic Land Rover models. This bush is supplied as one half of a split ...

Fixed Towing Drop Plate bolts to the rear tow bar to carry the towball at the correct towing height. This is the extra-long version, giving a grea...

Tappet kit

Plain Washer distributes the clamping load of a bolt or nut across the mounting surface and protects the surface as the fastener is tightened. Siz...

Tailgate Hook for the lower hinged tailboard, right-hand side. This pigtail (spiral) hook mounts on the body and retains the tailgate support stra...

Spring Washer for the fuel tank sender unit and fuel pick-up pipe fixings. Fitted beneath the retaining screws that secure the fuel gauge sender u...

Body Mounting Shim used to set the correct clearance and alignment between the body tub and the chassis mounting points. This thin flat shim is us...

Stub Shaft with a 10-spline drive coupling, a component of the axle half-shaft assembly. The stub shaft sits within the axle and transmits drive t...

Swivel Pin

Hub Oil Seal seals the rear hub assembly, retaining lubricant within the hub and excluding dirt and moisture from the wheel bearings. It runs on t...

Circlip - Gear Lever Spring Retention for the Series Land Rover gearbox gear lever assembly. This circlip retains the spring, retaining plate and ...

Handbrake Stud A mounting stud for the transmission (drum) handbrake within the braking system. It secures the transmission brake back plate to th...

Circlip An external retaining circlip for the gearbox primary pinion shaft. It seats in a machined groove on the shaft to retain the primary pinio...

Sediment Retainer for the fuel lift pump glass sediment bowl - the clamp that secures the glass bowl to the underside of the pump. It holds the bo...

Shock Absorber for the rear axle, damping suspension movement by converting the energy of spring oscillation into heat as the axle moves relative t...

Shock Absorber - rear suspension damper for the short-wheelbase chassis. Mounted between the rear axle and the chassis bracket, it controls spring...

Crankshaft Spigot Bush is the clutch pilot bush that presses into the rear face of the crankshaft, between the engine and the clutch. It supports ...

Parabolic Spring Kit for the rear leaf-sprung suspension. Parabolic springs replace the standard multi-leaf semi-elliptic springs with a smaller nu...

Free Wheeling Hub Kit - manual locking front-axle hubs that connect or disconnect the front halfshafts from the road wheels. Set to free, the front...

Spherical Bearing Bush - Clutch Cross Shaft for Series 1, Series 2, and Series 3 Land Rover vehicles. The clutch cross shaft is supported at its p...

Starter Pinion Retaining Kit for the inertia (Bendix) drive of the starter motor fitted to 4-cylinder and 6-cylinder petrol engines. The starter p...

Drop Plate Strengthener for the towing equipment assembly. It acts as a spacer and strengthener for the towing jaw and the towing jaw/ball fixings...

Plain Washer with a 1/4" bore, used as a general-purpose flat washer. Fitted under a bolt head or nut, it spreads the clamping load over a wider a...

Folding Side Step - Series

Switch - Fuel Tank Tap is an electrical switch used to operate the fuel tap selection on Land Rover Series I, Series II, Series IIA, and Series III...

Tailgate Chain Bracket

Glow Plug Lead in the diesel glow plug (heater plug) pre-heat circuit. This short 5" lead interconnects glow plugs wired in series and is not inte...

Winch Remote Control operates an electric recovery winch wirelessly, allowing the operator to stand clear of the winch line during recovery. Wirel...

Fuel Tank Outrigger is a rear chassis outrigger forming part of the body & chassis assembly. It welds to the main chassis rail to support the ...

Rotor Arm for the 24V shielded ignition distributor. The rotor arm mounts on the top of the distributor shaft and, as it rotates, routes the high-t...

Shock Absorbers for the rear axle, supplied as a matched pair. Each damper controls suspension movement by converting the energy of spring oscillat...