Land Rover Series 1 Parts

Monograde Engine Oil SAE 30 - a single-grade mineral engine oil for early petrol engines built before around 1960. The non-detergent formulation l...

Polyurethane chassis- and spring bushes as well as shock absorber bushes for all Series Short Wheelbase and Series 1 and 2/2A LWB. (For S3 LWB use ...

Set Screw retaining the top cover plate of the Series gearbox. A 4BA round-head fastener, sherardised finish, used to secure the cover plate on to...

Spring Clip for the rear end door trim casing, part of the interior trim fixings. The sprung clip retains the rear door card (trim casing) to the ...

Transfer Box to Gearbox Mounting Stud, 2" length, used to fasten the transfer case to the rear of the main gearbox casing. This stud forms part of...

Threaded Core Plug seals a threaded aperture in the engine block casting, used on the 4-cylinder petrol engine as a blanking plug for a redundant h...

Fluid Reservoir for the hydraulic braking and clutch system on the early Land Rover Series I. This metal reservoir feeds the Girling master cylinde...

Bolt securing the gearbox to the transfer box in the drivetrain. This fixing clamps the main gearbox housing to the transfer box. It applies to th...

Swivel Pin Seat Cone for the front axle swivel housing. This cone provides the precision seating surface on which the swivel pin locates within th...

Pinion Bearing Retaining Plate for the Power Take-Off (PTO) unit on Series Land Rovers. This retaining plate locates and secures the pinion bearin...

Heater Plug Lead in the diesel glow plug pre-heat circuit. This 10" interconnecting lead links the No.2 and No.3 heater (glow) plugs, carrying cur...

Overdrive Needle Bearing for the front of the mainshaft in a Fairey overdrive unit. The bearing supports the overdrive clutch sleeve on the mainsh...

Voltage Regulator for the dynamo charging circuit – the Lucas RB340 control box. Wired between the C40 dynamo and the battery, the control box reg...

Front Door Seal Kit re-seals the right-hand front door aperture, supplied with the rivets needed to fit it. The kit contains six door sealing rubb...

Crown Wheel & Pinion Set - the final-drive gear pair housed within the axle differential. The pinion takes drive from the propshaft and turns t...

Transfer Box Sump Cover is a finned billet aluminium cover plate that replaces the pressed-steel sump cover on the underside of the transfer case. ...

Upgrade your Land Rover's steering system with Heavy-Duty Steering Arms, designed for superior strength and performance, especially in off-road con...

Inner Tube for 7.50 x 16 and 7.00 x 16 tyres, fitted inside the tyre on tube-type wheels to hold the air pressure. Supplied with a small diameter ...

Spare Wheel Cover in plain black vinyl, sized to fit a 600 x 16 spare wheel and tyre (roughly a 195/80 R15 metric equivalent). It slips over the m...

Footwell Repair Panel for the right-hand (offside) footwell - a body repair section covering the footwell floor and inner side panel. For right-han...

Footwell Repair Panel for the left-hand (nearside) footwell - a body repair section covering the footwell floor and inner side panel. For right-han...

Doortop Unglazed - LH

Distance Piece for the LT76 gearbox mainshaft. This spacer maintains the correct axial position of components along the mainshaft within the LT76 ...

Screw: pan head self-tapping screw.

LED Driving Light - round auxiliary driving light with a 4" (100mm) diameter housing and 50W LED output. Intended for external mounting as a suppl...

Locking Nut for the steering linkage, retaining a track rod end onto the drag link or track rod. Once the joint is set to position, the nut is tigh...

Kinetic Recovery Rope - vehicle recovery accessory for extracting a bogged or stuck vehicle. Unlike a static strap, a kinetic rope stretches under...

Seat belt SECURICON

Bush

Screw - 2BA x 1" is a round head screw in British Association (BA) thread form, 2BA size, 1 inch in length. Used throughout the Series Land Rover ...

Fuel Filler Screw is a 2BA x 3/8" fastener used to secure the fuel filler fitting. It retains the fuel filler to the body panel; the companion nut...

Felt Seal for the clutch and brake pedal shaft, fitted in the pedal box where the cross-shaft passes through the housing. The felt washer seats ar...

Rear Axle Stub for the rear axle assembly on early Series Land Rovers. The axle stub is the outboard section of the rear axle shaft assembly, carr...

Choke Cable for the carburettor cold-start system. The cable links the dash-mounted choke control to the carburettor, operating the choke mechanis...

Light Socket for the inspection lamp on Series Land Rover vehicles. This black bayonet-type bulb holder is used in the inspection lamp assembly, p...

Crankshaft Front Key locates and locks the timing sprocket or front pulley hub to the crankshaft snout, preventing rotational slip between the cran...

Bearing Housing for the rear mainshaft bearing of the LT76 four-speed gearbox. The housing locates and retains the bearing that supports the rear ...

Handbrake Catch Pawl, the ratchet claw of the transmission parking brake mechanism. It engages the toothed quadrant on the handbrake lever, lockin...

Differential Bearing for the Rover-type axle, part of the differential carrier assembly inside the axle case. It supports the differential carrier...

Front Door Check Strap, part of the front door hinge and retention hardware. Connecting the front door to the body pillar, the check strap limits ...

Seat Base Corner Capping in plastic. Fitted at the outer corners of the front seat base frame, this capping provides a neat finished edge and prote...

Barrel Lock and Key, Set of Three for the door locks, supplied as three keyed lock barrels each with a key. Each barrel is the cylinder the key tu...

Lower Tailgate for the rear of the body - the drop-down tailboard panel that closes off the rear of the load area. Hinged along its lower edge, it...

Timing Chain Tensioner maintains correct tension on the timing chain within the engine timing case, preventing chain slap and ensuring accurate val...

Crown Wheel Bolt with British Standard Fine (BSF) thread, used to secure the crown wheel to the differential carrier in early Land Rover axles. Tw...

Differential Crown Wheel Locking Tab is a tab washer used in the axle differential assembly to lock and retain the crown wheel bolts after tighteni...

Ball Race - Steering Box (Adjusting) is a component of the recirculating-ball manual steering box assembly, used to control pre-load and end-float ...