Land Rover Series 1 Parts

Gasket Kit covering the lower (bottom-end) assembly of the Land Rover Series I 2.0L petrol engine. Provides the sealing gaskets required for a bott...

Brake Lining - Rear is a replacement friction lining for the rear drum brake assembly on long-wheelbase Land Rover models, covering 109-inch, 110-i...

Mainshaft Thrust Washer - 2nd Gear (0.125") is a selective shim located within the Series gearbox, fitted to control axial play on the second gear ...

Bolt - 1/2 UNF x 1 is a hexagon-head set bolt in 1/2 UNF (Unified National Fine) thread, 1 inch in length, used to secure the engine mounting brack...

Set Screw - Water Pump Spindle is a locking fastener that locates the water pump spindle within the water pump housing on Series engines produced b...

Front Halfshaft Bearing - roller bearing supporting the inner end of the front halfshaft within the front axle housing. Located at the inboard end...

Layshaft Split Ring Halves are a matched pair of semi-circular retaining ring halves used in the Land Rover Series I and II gearbox assembly. The ...

Bolt with Whitworth (BSW) thread - 1/4 inch diameter, 1-1/4 inch length, sold individually. Used across Series Land Rover applications requiring t...

Braided Earth Strap with Battery Clamp - 300mm for the vehicle electrical grounding circuit. This braided copper earth strap is fitted with an int...

Reverse Gate Bracket is the fixed section of the reverse-gate stop within the gear-lever mounting on the Series four-speed gearbox. It forms the g...

Gasket NLA after stock ends

Washer

Thrust washer diff 0.050"

Seat Box Corner Protector set, supplied as a pair to guard the exposed corners of the seat box against knocks and wear. Each protector is CNC cut ...

Whitworth Socket Set - 3/8in Drive - 7-Piece

bushes needed to machine the Series LT76 transfer case for the High Ratio Gear Set (HGRS.)

Universal Joint for the propeller shaft, measuring 75 mm across the bearing caps with a 27 mm cap diameter. The universal joint is the cross-and-b...

Sealed to prevent the access of mud. Driving off-road you'll know how easy it is for the standard Land Rover hand brake to get bunged up with dirt...

Replacement brake pads for handbrake conversion kit - DA5537

Braided Earth Strip is a flexible braided conductor that forms an electrical earth (ground) bond between two points in the vehicle. It provides a ...

Retainer Oil Seal On Output Housing

Headlamp Bowl Seal - the gasket that seals the 7-inch headlamp bowl against the surrounding body panel. Fitted around the lamp aperture, it closes...

7" Crystal Halogen Headlamp - round headlamp unit for the front lighting assembly, supplied as a matched pair. The clear crystal lens works with a...

Crystal Headlamp - a matched pair of 7-inch round crystal halogen headlamps for right-hand-drive applications. The clear (crystal) lens and facete...

7" Crystal Halogen Headlamp - round headlamp unit for the front lighting assembly, supplied as a matched pair. The clear crystal lens works with a...

Polyurethane Bush Set in yellow, supplied for suspension mounting points that use a rubber-style bush. Supplied as a set of yellow polyurethane bu...

Junction Box – 6 Terminal is a bulkhead-mounted wiring junction box within the electrical system, providing six terminals for the connection and di...

Headlamp Light Unit - a 7 inch round headlamp light unit for the front lighting system, using the British Pre-Focus (BPF) bulb mounting. The refle...

Four-Wheel Drive Selector Lever Bush for the transfer box gearchange linkage. The bush locates the four-wheel-drive selector lever at its pivot, t...

Restore the performance of your Land Rover Series with this AVM Freewheeling Hub Repair Overhaul Kit. Designed for 10-spline freewheeling hubs, thi...

Girling Shock Absorber for the front suspension, a hydraulic damper for heavy-duty suspension applications. Mounted between the axle and the chass...

Rotor Arm for the Lucas distributor in the ignition system of the 2.0L and 2.25L 4-cylinder petrol engines (up to engine suffix C). Driven by the ...

Layshaft Bearing for the Series manual gearbox. It supports the layshaft (countershaft) within the gearbox casing, allowing the constant-mesh gear ...

T-Piece Hose Connector is a three-way junction fitting used in a flexible hose run. It joins three hose ends at a single point, allowing a hose li...

Halo & Bar 7" LED Headlights - a pair of sealed LED headlamp units that replace the original lamps in a traditional 7" round headlamp aperture,...

7 Inch Round LED Headlamp for the front lighting system, replacing the conventional 7-inch round sealed-beam or halogen headlamp. The LED light so...

Rear Brake Kit for the rear drum brake assembly, covering the friction and hydraulic wear parts fitted inside the rear brake drums. The wheel cyli...

Standard seat set covering the full front seat row of a Series cab – both outer seats and the centre seat. The set consists of six pieces: two out...

Sliding Window Kit - Deluxe, supplied as a pair for the rear body sides. The kit fits a horizontally sliding glass window into the rear side panel...

Mirror Arm - standard-length exterior mirror arm, 178 mm (7 in), for the front wing. Mounts to the top of the front wing or to the door hinge usin...

Cylinder Head Overhaul Kit

Cylinder Head Overhaul Kit - Series I

Cylinder Head Overhaul Kit