Land Rover Series 1 Parts

Synthetic Winch Rope - 10mm x 24m - 10,000 lbs for 4x4 winch recovery. This synthetic fibre winch rope is rated to 10,000 lbs (approx. 4,536 kg) b...

Locking Nut for the steering linkage, retaining a track rod end onto the drag link or track rod. Once the joint is set to position, the nut is tigh...

Seat belt SECURICON

Protector Top Wing - Series

Rear Door Trim Panel - a black interior trim panel that finishes the inner face of the rear side-hinged door, covering the door frame to give a cle...

Drive Screw for use in Land Rover body, chassis, and hardware assembly. A No.14 × 1" drive screw, supplied individually.

Halfshaft Retaining Collar fitted to the axle halfshaft to locate and retain the halfshaft bearing on the shaft. The collar is pressed onto the ha...

Fuel Filler Hose

Drop Arm for the manual steering box. The drop arm splines onto the steering box rocker shaft and converts the box's rotary output into the fore-an...

Light socket red

Shock Absorber Bush (sleeve type) fitted at the shock absorber mounting points in the suspension system. This rubber sleeve bush locates within th...

Gearbox Dowel is a precision locating pin used within the Series Land Rover gearbox assembly. It ensures correct alignment between gearbox casings ...

Screw - a set screw for the gearbox top cover plate. It secures the cover plate to the top of the main gearbox casing. Not used on the Stage 1 V8 ...

Flywheel Ring Gear for four-cylinder petrol engines. The ring gear is shrink-fitted to the periphery of the flywheel and meshes with the starter mo...

Plain Nut for use as a standard fastener across Land Rover applications. A plain (non-locking) hex nut for general assembly and repair work.

Mainshaft Gear - 1st Speed is a 29-tooth first-speed gear that runs on the mainshaft within the manual gearbox gear train. As a non-synchronised c...

Steel Ball for the timing chain tensioner, 7/32 in diameter. Seats within the tensioner mechanism to help maintain correct timing chain tension.

Bullet Connector, single-sleeve, one-way. Accepts a standard bullet terminal and is used throughout Land Rover wiring harnesses for individual wire...

Hood Stick Kit - the framework of bows and sticks that forms the skeleton of a canvas soft top (tilt), carrying and tensioning the fabric over the ...

Upper Tailgate Lock Cap for the rear end door handle assembly. This small plastic cap fits over the end of the upper tailgate handle, covering and...

Rivet, semi-tubular with a semi-round (truss) head, 3/16 in diameter and 3/8 in long. It secures door weatherstrip and seals to the body aperture....

Crown Wheel Bolt with British Standard Fine (BSF) thread, used to secure the crown wheel to the differential carrier in early Land Rover axles. Tw...

Radiator Top Hose forms part of the engine cooling circuit, connecting the top tank of the radiator to the coolant outlet at the cylinder head. Th...

Pipe clamp 109" intermediate exhaust pipe centre bracket (For the bottom bracket use 264889.)

Rocker Cover Stud for the cylinder head on early Land Rover 4-cylinder engines. The rocker cover stud is a threaded fastener installed into the cy...

Valve Stem Oil Seal fits over the inlet valve stems to limit oil consumption past the valve guides in the cylinder head. It is used on 2.25L petrol...

Gear - 2nd - Pair for the Series Land Rover four-speed main gearbox. This pair comprises the matched 2nd speed gears for both the mainshaft and th...

Main Starter Spring is the principal return spring within the starter motor assembly used on Series I, II, IIA, and III vehicles. It operates withi...

Output Shaft - Front for the Land Rover transfer gearbox. The front output shaft carries drive from the transfer gearbox to the front propshaft, su...

Mudshield Output Shaft

Plunger for the transfer box selector mechanism. Locates within the transfer selector assembly to provide positive engagement and detenting of tra...

Mainshaft Thrust Washer for the Series I and Series II gearbox assembly. This 0.135 in (135 thou) washer controls the axial location of 3rd gear o...

Flexible Brake Hose - hydraulic hose carrying brake fluid from the rigid chassis or axle pipe to the wheel cylinder. Forms the flexible link acros...

Inner Pinion Bearing for the Land Rover Series axle differential, supporting the pinion shaft at the inboard (crown wheel) end within the different...

Transfer Box Mainshaft is the central rotating shaft within the transfer box assembly, running through the gear train and transmitting drive betwee...

Circlip - Rear Mainshaft Bearing for the Series Land Rover gearbox. This circlip retains the rear mainshaft bearing within the gearbox casing, pre...

Shim 0.005

3 man seat Techno Exmoor trim EX4188 EXT006-TC

Inlet Rocker Bush for the valve gear, forming the bearing surface between the inlet rocker arm and the rocker shaft. The bush locates the inlet ro...