Land Rover Series 1 Parts

Timing Chain Idler Wheel runs against the timing chain within the front timing case, guiding the chain and helping maintain its tension between the...

Drain Plug for the axle casing and fuel tank. This brass threaded plug seals the drain aperture at the bottom of the differential and axle casing,...

Clevis Pin - pivot pin used in the mechanical brake and transmission linkages. It passes through a forked clevis and the eye of a mating rod or lev...

Leather hasp civilian

Oil Seal - Clutch Cross Shaft for Series 1 and Series 2 Land Rover vehicles (1948-1971). The clutch cross shaft passes through the bellhousing and...

Self-Locking Nut, 3/8" BSF, used to secure propshaft fasteners within the drivetrain. The deformed thread form provides a self-locking action that...

Outer Distance Piece for the front axle swivel pin housing. The distance piece is a spacer that sets the position of the swivel pin bearing within...

Exhaust Hanger Plate - a flexi-mount bracket within the exhaust system mounting hardware. It suspends the exhaust from the vehicle underframe, its...

Collar Bush for the four-wheel-drive selector mechanism in the two-speed transfer box. It seats on the high-range 4WD selector rod, locating the s...

Transfer Box Lever Lock Nut used to secure the selector linkage at the transfer case. This half nut (thin profile locking nut) threads onto the sel...

Steering Drag Link - With Bracket - 73cm is a steering linkage rod, supplied with an integrated steering damper bracket. The drag link transmits s...

Cleat Rope Hook Body Side All and Classic (Softtop) - Series Defender

Spring Washer, M8, a split ring washer used with M8 bolts and nuts to prevent fastener loosening caused by vibration and cyclical loading. The spl...

4-Leaf Parabolic Rear Spring Pair for the rear suspension of Series long-wheelbase Land Rovers. Parabolic leaf springs use a progressive, variable...

Steel Road Wheel is a welded steel road wheel with a 6.5 x 16 inch rim, finished in black with a Wolf-style profile for road use with tubeless tyre...

Gearbox Gasket for the LT76 four-speed gearbox with integral transfer assembly. It seals a mating housing face within the gearbox and transfer cas...

Round Mirror Head is the circular exterior mirror glass and housing that mounts on a wing- or fender-mounted mirror arm. It gives the driver a rea...

Clutch Plate is the friction-lined driven plate of the clutch assembly, 9 inch (229 mm) diameter. Its splined hub engages the gearbox input shaft ...

Fixed Towing Drop Plate bolts to the rear tow bar to carry the towball at the correct towing height. The plate is a fixed, non-adjustable type set...

Window Channel - Vertical - the upright glass run for the Truck Cab side window, part of the door glazing assembly. It lines the vertical edge of ...

Floor Mounting Pad is a 5mm rubber spacer pad used at the rear body floor support mounting, fitted between the body and the chassis-mounted support...

Lock Washer is a folding lock tab used in the front axle swivel pin housing assembly. Fitted beneath a 3/8" stud fixing, the tab is bent up agains...

Oil Pump Lock Tab, part of the engine oil pump assembly. The lock tab is a tab washer fitted under the oil pump retaining fastener; once the faste...

Exhaust Connecting Pipe is the intermediate section of the exhaust system for Series short wheelbase vehicles fitted with the 2.25L diesel engine, ...

Front Spring Dowel for the 9-leaf front road spring, part of the leaf spring suspension assembly. The dowel is the centre locating pin that passes...

Transfer Box Output Mud Shield Shield that fits over the transfer box output flange to protect the output shaft oil seal from mud, water and debris...

Sump Gasket seals the joint between the oil sump and the cylinder block within the engine lubrication system, preventing oil leakage at the sump fl...

Track Rod Clamp Kit secures the track rod within the steering linkage assembly, holding the joint in position so the steering geometry stays set. ...

Military red rear stop light lens

Shock Absorber for the front suspension on the short-wheelbase (SWB) chassis. Mounted between the front axle and the chassis, the hydraulic damper...

Hex Nut - M8 is a standard six-sided metric threaded fastener with an 8 mm nominal thread diameter. It threads onto a matching M8 bolt or stud to ...

Headlamp Bowl Seal - the gasket that seals the 7-inch headlamp bowl against the surrounding body panel. Fitted around the lamp aperture, it closes...

Bulkhead Repair Panel with Vents - Right-Hand is a weld-in repair section for the upper corner of the bulkhead, incorporating the fresh-air vent su...

Gear Selector Plunger is the interlocker pin fitted to the 1st and 2nd gear selector shaft in the gearbox top cover. It prevents simultaneous selec...

Door Clevis Pin for the door check strap mechanism. The pin locates the check strap to its mounting bracket, forming the pivot the strap works aga...

Fuel Pipe Sealing Washer seals the fuel pipe union at the DPA diesel injection pump. Fitted at the union connection, it is compressed between the ...

Shackle Pin

Rear Spring Hanger is a chassis mounting bracket in the rear leaf-spring suspension, forming the forward anchor point that carries the front eye of...

Interior Lamp - courtesy lamp for the passenger compartment. Provides interior illumination as part of the interior lighting circuit, typically sw...

Nut - 2BA, a small-diameter fastener in the British Association (BA) thread standard. 2BA refers to the No.2 size within the British Association t...

Gear Lever for the main gearbox, right-hand drive configuration. The gear lever is the primary driver interface in the gearbox change mechanism, t...

Tappet Slide for Land Rover 4-cylinder engines, covering the Series I, Series II, Series IIA, and Series III (2.0L Diesel and 2.25L Petrol and Dies...

Plain Washer M8

Camshaft Bearing for the 2nd, 3rd and 4th journal positions of the four-cylinder engine. The bearing shell is fitted into its housing in the cylind...

Drive Screw with a round head, a general body and chassis fixing. The steep-helix thread lets the screw be driven into a pre-drilled hole with a h...

Clutch Cover is the pressure plate assembly of the clutch, 9 inch (229 mm) diameter, coil-spring type with three release fingers. It bolts to the ...

Bronze Distance Piece Mainshaft 1954-71

Front Exhaust Pipe forms the front section of the exhaust system, mounting to the exhaust manifold by a four-stud flange. It carries exhaust gas f...