Land Rover Series 2 & 3 Parts

Core Plug, 1 7/8" diameter, sealing a casting core hole such as those in the inlet manifold and engine castings. Core plugs close the openings lef...

Relay - 12V automotive changeover relay with a 30A contact rating, twin make. The five-pin configuration provides two normally-open contacts, allo...

Swivel Housing Washer for the swivel pin housing drain plug, part of the front axle swivel assembly. The sealing washer fits beneath the drain plu...

Electronic Distributor - complete distributor assembly for the 4-cylinder petrol engine, supplied with the electronic ignition conversion already f...

Shim .003" for swivel pins

Track Rod End Boot for the steering track rod end ball joint. This rubber boot fits over the track rod end housing, sealing the ball joint against...

Decoke Head Gasket Set for the 2.25L 4-cylinder diesel engine - the top-end gasket set used for a full decarbonising (decoke) job or when removing ...

Engine Bottom-End Gasket Set for the 2.25L 4-cylinder petrol engine, supplying the lower-engine gaskets and seals used during a bottom-end overhaul...

Bolt for the suspension mounting. A 7/16" UNF thread bolt of 6.5" length, used at the upper suspension mounting to secure the shock absorber and sp...

Water Temperature Sender threads into the cooling system and measures engine coolant temperature, feeding the signal to the dashboard temperature g...

Clutch Release Fork Kit for the manual transmission clutch release mechanism, built around a cast release fork. The fork pivots on its mounting in...

Rear Shock Absorber - rear suspension damper for the long-wheelbase chassis. Mounted between the rear axle and the chassis bracket, it controls sp...

Flasher Unit for the direction-indicator circuit, of the 2-pin type without trailer-socket provision. The flasher unit switches the current to the...

Tailgate Chain Cover - a pair of protective sleeves that fit over the two retaining chains supporting the rear tailgate. Each chain links the tail...

Bolt, a hexagon-head fastener with a 5/16" UNF thread, 7/8" long. This imperial fastener is of the UNF (Unified National Fine) thread series and i...

Heater Control Finger Grip The finger grip fitted to a heater control slider on the heater (HVAC) control panel, operated in the up/down plane. It...

Distributor Rotor Arm for the 3.5L V8 petrol ignition system. The rotor arm sits on top of the distributor shaft beneath the cap and rotates to dis...

Hazard Flasher Relay - the switching relay in the hazard warning circuit. When the hazard switch is operated, the flasher relay pulses all four di...

Crankshaft Timing Chain Sprocket The drive sprocket mounted on the nose of the crankshaft within the timing chain drive of the Rover V8 petrol engi...

Core Plug (Cup Type) for sealing the core holes left in the engine block casting after the sand cores are removed during manufacture. The cup-shap...

Bolt 5/16" UNF x 2" is a hex-head set bolt with a 5/16-inch Unified National Fine (UNF) thread at 24 threads per inch and a 2-inch shank length. I...

Fixing Screw for the front door hinge and check strap assembly. This screw secures the door hinge and the check strap (door-stay) to the body pill...

Differential Drive Flange for the Salisbury rear differential. It bolts to the differential pinion shaft and forms the coupling face to which the r...

Bolt with a 3/8" UNF (Unified National Fine) thread and a 1-7/32" length. A standard imperial-thread fastener for chassis, driveline and body fixi...

Grommet - rubber blanking grommet for the transmission (gearbox) tunnel cover. This rubber grommet seals the access aperture in the gearbox tunnel...

Hexagon Nut with a 7/16" BSF (British Standard Fine) thread. A standard nut cut to the British Standard Fine thread form used throughout the fixin...

Lower Swivel Pin O-Ring for the front axle swivel housing assembly. It seals the joint at the lower swivel pin, where the steering arm and lower pi...

Bottom End Gasket Set for the overhaul of the 2.25L diesel engine (3- and 5-main-bearing), covering the gasket and joint requirements of the lower ...

Clutch Cover (pressure plate assembly) for the clutch on 4-cylinder petrol applications. The cover bolts to the flywheel and houses the diaphragm ...

4WD High Gear Selector Spring for the transfer box four-wheel-drive selector mechanism. The spring acts on the high-range four-wheel-drive selecto...

Swivel Pin Shim for the front axle swivel housing assembly. This 0.030" shim is fitted beneath the upper swivel pin retaining plate and is used to ...

Front Halfshaft Bearing - roller bearing supporting the inner end of the front halfshaft within the front axle housing. Located at the inboard end...

Clutch Master Cylinder Overhaul Kit for rebuilding a CV-type master cylinder, allowing the worn internal components to be renewed without replacing...

Handbrake Pull-Off Spring for the transmission-mounted drum handbrake assembly. This return spring retracts the brake shoes against the backplate ...

Stop/Tail Lamp Assembly for the rear lighting circuit, combining the tail (running) light and stop (brake) light in a single unit. The assembly mo...

Oil Pressure Switch threads into the engine block oil gallery and monitors lubrication system pressure. It operates the low oil pressure warning l...

Steering Box is the recirculating-ball power steering gear at the heart of the steering system, converting rotation of the steering column into the...

Con Rod Bearing Set for the 2.25L four-cylinder petrol engine. The set provides the big-end shell bearings that carry the connecting rods on the c...

Castle Nut (castellated nut) used to retain halfshafts, output shafts and differential pinion shafts in Land Rover axle and drivetrain assemblies. ...

Hose Clamp - 59-82mm is a worm-drive hose clip with a 60-80mm clamping range. The band is tightened by a captive worm screw to secure large-bore h...

Self-Tapping Screw – No. 8 × 1/2 in is a general-purpose fastener used across body, trim and electrical fixings, such as lamp guards, wheelguards, ...

Lock Washer secures a threaded fastener against loosening under vibration and thermal cycling. Fitted beneath the nut or bolt head, it bites into ...

Spring Washer - M6 single-coil spring lock washer. Fitted beneath a nut or bolt head, the split single-coil section bears against the fastener to ...

Hex-head bolt, 5/16" UNF thread, 1" long. Unified Fine (UNF) thread form with a hexagonal head for use with standard imperial spanners and sockets...

Hex Nut, 7/16" UNF, plain steel. This full hex nut secures the door top to the door base on Series models and is used at other 7/16" UNF fixing po...

7" round LED headlamp 12/24V chrome 78W LHD (pair)

Brake Pipe Union - a female union fitting for 3/16" (4.75mm) hydraulic brake pipe, with an M10 x 1mm thread. Machined from brass, it threads onto ...

Head Bolt Kit - a complete set of cylinder head bolts for the Rover V8 engine, securing the cylinder heads to the block and clamping the head gaske...