Land Rover Series 2 & 3 Parts

Valve Stem Seal - the seal fitted over the valve stem in the cylinder head to control the oil that passes down the stem into the port. This is the...

Steering Wheel is a 15-inch three-spoke replacement wheel that mounts to the steering column. It is supplied without a boss, so a separate fitting...

Track Rod End Boot Ring - spring retaining ring for the track rod end of the steering linkage. It clamps the rubber dust boot onto the track rod en...

Crankshaft Key locates the timing gear and crankshaft pulley on the crankshaft nose, fixing their angular position relative to the shaft. It trans...

Left-Hand Exhaust Downpipe for the 3.5L V8 EFI engine, non-catalyst exhaust configuration. Connects the left cylinder bank exhaust manifold outlet ...

Oil Pump Relief Valve Spring - sets the pressure at which the oil pump's relief valve opens. It holds the relief valve plunger closed against the ...

Water Pump circulates coolant through the engine cooling system. It mounts to the front of the Rover 3.5L V8 engine and is driven by the auxiliary...

Rocker Arm for the rocker shaft valvetrain assembly of the Rover V8 petrol engine. The rocker arm pivots on the rocker shaft and transmits the lif...

Rocker Arm for the rocker shaft valvetrain assembly of the Rover V8 petrol engine. The rocker arm pivots on the rocker shaft and transmits the lif...

Ignition Module & Link Lead - a kit for the 3.5L Rover V8 petrol engine ignition system, comprising the electronic ignition module (amplifier) ...

Crankshaft Spigot Bush is the clutch pilot bush that presses into the rear face of the crankshaft, between the engine and the clutch. It supports ...

Rocker Arm - Steel - LH for the valve train of the Rover V8 engine, part of the Cylinder Head & Valve Train assembly. This steel rocker arm pi...

Shock Absorber Bush Set for the shock absorber mountings. This set provides the bushes that locate each shock absorber at its mounting eyes, insul...

P-Clip - 19/64" x 3/8" is a pressed-steel P-profile retaining clip used to route and secure fuel lines, brake pipes, or wiring looms against a chas...

Warning Label A warning label relating to the battery negative (earth) cable connection. It is applied in the vehicle to convey a safety instructi...

Starter Motor for V8 petrol engines, operating within the engine electrical starting system. The solenoid-actuated pinion engages the flywheel rin...

Flywheel Dowel is a locating dowel that registers the flywheel to the crankshaft rear flange. Pressed into the crankshaft flange, it sets the angu...

Rocker Cover Breather Hose - Left-Hand for the crankcase ventilation system of the Rover 3.5L V8 twin-carburettor engine. This hose connects the l...

seal washer for block coolant drain plug. - All 4-cylinder engines upto 1998 (except VM diesel)

Clip - 13/64" x 3/8" is a single-bolt retaining clip used to secure wiring harnesses, vacuum lines, and small-bore hoses to body or engine bay brac...

Fuel Pump Adaptor for mounting the external fuel pump on petrol engines. It provides the interface between the external fuel pump and its mounting...

Plastic Washer serves as a spacing and anti-friction washer at the front seat hinge and the rear door check arm pivot. Fitted at the pivot joint, ...

Gearbox Side Cover Gasket for the LT95 4-speed V8 gearbox. This gasket seals the side cover to the gearbox casing, preventing oil leaks from the ge...

Gear Lever Damper for the LT95 four-speed gearbox gear-change mechanism. This damping washer fits at the base of the main gear lever, absorbing vi...

Special Bolt for retaining the tappets in the cylinder block, part of the camshaft and tappet assembly. This is a specific-design fastener that se...

Filler and Level Plug for the V8 4-speed gearbox and for differential assemblies across a wide range of classic Land Rover models. Fitted at the s...

Distributor O-Ring, the sealing ring for the ignition distributor on the 3.5L V8 petrol engine. The O-ring seals the distributor base where it loc...

Fuel Sedimentor is a water and sediment trap in the diesel fuel supply line, installed upstream of the fuel filter and injection pump. Fuel passes...

Sedimentor Drain Plug Seal for the sedimentor in the diesel fuel supply. The sedimentor separates water and heavier contaminants from the fuel ahea...

Nutsert - 5/16" UNF is a blind rivet nut (rivnut) with a 5/16" UNF internal thread. A nutsert is installed into a pre-drilled hole in sheet metal ...

Circlip An external retaining circlip for the gearbox primary pinion shaft. It seats in a machined groove on the shaft to retain the primary pinio...

Screw 3/8" UNC x 1-1/2" used to secure the starter motor to the engine block on Rover V8 petrol engine applications. This is a 3/8 inch Unified Nat...

Screw hex HD 3/8" UNC x 1-1/4"

Plain Washer distributes the clamping load of a bolt or nut across the mounting surface and protects the surface as the fastener is tightened. Siz...

Plain Washer - Large 5/16" is a large plain washer for use with 5/16" fastenings, providing load distribution beneath bolt heads and nuts across La...

Winch Remote Control operates an electric recovery winch wirelessly, allowing the operator to stand clear of the winch line during recovery. Wirel...

Union Nut for the fuel pipe in the fuel delivery system. This M12 union nut clamps a fuel pipe to its mating union or component port, drawing the ...

Spring Washer for use across a wide range of fixings and assembly applications on Land Rover vehicles. This split-ring spring washer is placed ben...

Fuel Tank Drain Plug - the threaded plug that seals the drain point at the base of the fuel tank. Removing it allows the tank to be drained for se...

Pas op alle  V8 benzine motoren met Stromberg carburateurs

Camshaft for the five-bearing four-cylinder engine, running in the cylinder block as the core of the overhead-valve valvetrain. Driven from the cr...

Bolt with a 3/8" UNF (Unified National Fine) imperial thread and a 1-1/2" shank length. A hex-head fastener for general assembly and fixing applic...

Bolt with a 3/8" UNC (Unified National Coarse) imperial thread and a 2" shank length. A hex-head fastener used in body, chassis and general assemb...

Rear Fog Lamp for the rear lighting circuit, providing the high-intensity red rear light used to make the vehicle conspicuous from behind in poor v...

Shock Absorber Washer Retaining washer for the rear shock absorber lower mounting. Part of the rear suspension assembly, it locates over the lower...

Camshaft Bearing Set comprises the plain bearing shells that support the camshaft within the cylinder block of the four-cylinder engine. The beari...

Camshaft Bearing, the front bearing in which the camshaft front journal runs within the cylinder block. It supports the forward end of the camshaf...

Ignition Coil for the V8 petrol ignition system. It converts the low-voltage supply into the high-tension voltage that fires the spark plugs throug...