Land Rover Series 2 & 3 Parts

This camshaft sprocket is designed for Land Rover V8 engines, providing precise timing and reliable performance.

Rocker Cover Gasket for the V8 petrol engine, cork construction. The gasket seals the joint between the rocker cover and the cylinder head, contai...

Handbrake Return Spring is part of the transmission-mounted drum-type handbrake, acting on the relay lever within the parking brake mechanism. Whe...

Thrust Washer for the upper swivel pin Railko bush, part of the front axle steering swivel assembly. The Railko bush forms the upper pivot bearing...

Core Plug, 1 7/8" diameter, sealing a casting core hole such as those in the inlet manifold and engine castings. Core plugs close the openings lef...

Relay - 12V automotive changeover relay with a 30A contact rating, twin make. The five-pin configuration provides two normally-open contacts, allo...

Swivel Housing Washer for the swivel pin housing drain plug, part of the front axle swivel assembly. The sealing washer fits beneath the drain plu...

Electronic Distributor - complete distributor assembly for the 4-cylinder petrol engine, supplied with the electronic ignition conversion already f...

Wheel Cylinder - LH Front for the front drum brake assembly on long wheelbase Series models. This hydraulic wheel cylinder is mounted at the left-...

Interior Grab Handle - interior pull handle for the rear side door, used to draw the door closed from inside the cab. It fixes to the inner face o...

Chassis Bush - 88in - Front is a rubber bush that fits the rear mounting point of the front leaf spring, locating the spring in the chassis-side sh...

Bottom radiator hose SII(A) 2.25

Transfer Lever Knob in yellow, for the four-wheel-drive engagement lever on the transfer gearbox. It threads onto the top of the selector lever an...

Specifically designed for Series vehicles equipped with the Weber 34 ICH 2.25 carburettor, this kit includes all the essential components needed to...

Fuel Level Sender for the petrol fuel tank, part of the fuel gauge system. The sender mounts in the top of the rear fuel tank, where a float arm f...

Shim .003" for swivel pins

Gearbox Reverse Stop Spring for the gear selector mechanism. The spring acts on the reverse stop plunger, providing the resistance the gear lever ...

Track Rod End Boot for the steering track rod end ball joint. This rubber boot fits over the track rod end housing, sealing the ball joint against...

Decoke Head Gasket Set for the 2.25L 4-cylinder diesel engine - the top-end gasket set used for a full decarbonising (decoke) job or when removing ...

Engine Bottom-End Gasket Set for the 2.25L 4-cylinder petrol engine, supplying the lower-engine gaskets and seals used during a bottom-end overhaul...

Bolt for the suspension mounting. A 7/16" UNF thread bolt of 6.5" length, used at the upper suspension mounting to secure the shock absorber and sp...

Water Temperature Sender threads into the cooling system and measures engine coolant temperature, feeding the signal to the dashboard temperature g...

Cylinder Head Gasket - non-adhesive type, for the 2.25-litre petrol engine. Seals the joint between the cylinder head and the cylinder block, cont...

Speedometer Drive Cable transmits rotational drive from the gearbox speedometer take-off to the speedometer head in the instrument panel. An inner...

Clutch Release Fork Kit for the manual transmission clutch release mechanism, built around a cast release fork. The fork pivots on its mounting in...

Wheel Bearing Kit for overhauling one wheel hub to imperial specification, front or rear. The hub runs on an inner and an outer bearing, which car...

Rear Shock Absorber - rear suspension damper for the long-wheelbase chassis. Mounted between the rear axle and the chassis bracket, it controls sp...

Flasher Unit for the direction-indicator circuit, of the 2-pin type without trailer-socket provision. The flasher unit switches the current to the...

Tailgate Chain Cover - a pair of protective sleeves that fit over the two retaining chains supporting the rear tailgate. Each chain links the tail...

Wheel Stud, screw-in type, 9/16 BSF and threaded at both ends, fitting the front and rear axle hubs. The stud screws into the hub at one end; the ...

Bolt, a hexagon-head fastener with a 5/16" UNF thread, 7/8" long. This imperial fastener is of the UNF (Unified National Fine) thread series and i...

Heater Control Finger Grip The finger grip fitted to a heater control slider on the heater (HVAC) control panel, operated in the up/down plane. It...

Distributor Rotor Arm for the 3.5L V8 petrol ignition system. The rotor arm sits on top of the distributor shaft beneath the cap and rotates to dis...

Rotor Arm for the ignition distributor of the 2.6L 6-cylinder inline petrol engine. The rotor arm fits on the top of the distributor shaft and tur...

Hazard Flasher Relay - the switching relay in the hazard warning circuit. When the hazard switch is operated, the flasher relay pulses all four di...

Crankshaft Timing Chain Sprocket The drive sprocket mounted on the nose of the crankshaft within the timing chain drive of the Rover V8 petrol engi...

Core Plug (Cup Type) for sealing the core holes left in the engine block casting after the sand cores are removed during manufacture. The cup-shap...

Bolt 5/16" UNF x 2" is a hex-head set bolt with a 5/16-inch Unified National Fine (UNF) thread at 24 threads per inch and a 2-inch shank length. I...

Fixing Screw for the front door hinge and check strap assembly. This screw secures the door hinge and the check strap (door-stay) to the body pill...

Differential Drive Flange for the Salisbury rear differential. It bolts to the differential pinion shaft and forms the coupling face to which the r...

Selector Rod Rubber Grommet Washer is the rubber sealing element fitted around the reverse gear selector shaft at its exit point through the Series...

Railko Bush is the lower swivel bearing in the front axle swivel pin housing. It locates the bottom swivel pin and provides the low-friction pivot...

Bolt with a 3/8" UNF (Unified National Fine) thread and a 1-7/32" length. A standard imperial-thread fastener for chassis, driveline and body fixi...

Grommet - rubber blanking grommet for the transmission (gearbox) tunnel cover. This rubber grommet seals the access aperture in the gearbox tunnel...

Hexagon Nut with a 7/16" BSF (British Standard Fine) thread. A standard nut cut to the British Standard Fine thread form used throughout the fixin...

Wiper Blade for the windscreen wash/wipe system, 25 cm in length, of flat-blade construction. The blade attaches to the wiper arm and carries the ...

Chassis Bush - 88in - Front is a rubber bush that fits the rear mounting point of the front leaf spring, locating the spring in the chassis-side sh...

Lower Swivel Pin O-Ring for the front axle swivel housing assembly. It seals the joint at the lower swivel pin, where the steering arm and lower pi...