Land Rover Series 2 & 3 Parts

Exhaust Front Pipe in stainless steel, forming the first section of the exhaust system for the 2.25L petrol engine, between the manifold and the in...

Sedimentor Drain Plug Seal for the sedimentor in the diesel fuel supply. The sedimentor separates water and heavier contaminants from the fuel ahea...

Bonnet Stop Buffer is a rubber buffer that cushions the bonnet where it rests against the body when closed. Mounted on the front bodywork, it supp...

Nutsert - 5/16" UNF is a blind rivet nut (rivnut) with a 5/16" UNF internal thread. A nutsert is installed into a pre-drilled hole in sheet metal ...

Fuel Tank Outrigger - front right-hand chassis outrigger supporting the fuel tank on the short-wheelbase 88" chassis. Welded to the chassis frame,...

Exhaust Plate for the intermediate section of the exhaust system on 88" Short Wheelbase variants in left-hand drive (LHD) configuration. This plat...

Free-Wheeling Hub Repair Kit for 24-spline manual free-wheeling hubs. Manual free-wheeling hubs allow the front drive members to be disengaged fro...

Glow Plug Lead in the diesel glow plug (heater plug) pre-heat circuit. This short 5" lead interconnects glow plugs wired in series and is not inte...

Washer - a plain flat washer used as a general-purpose fastening component across many assemblies on the vehicle. Fitted under a bolt head or nut,...

Window Catch Mask fits behind the window catch on the rear side door. This plate seats between the catch and the door skin, masking and reinforcin...

Screw 3/8" UNC x 1-1/2" used to secure the starter motor to the engine block on Rover V8 petrol engine applications. This is a 3/8 inch Unified Nat...

Hardtop Support Bracket for the rear body, forming part of the upper fixings that secure the hardtop to the bodyshell. The bracket supports the si...

Fuel Tank Outrigger is a rear chassis outrigger forming part of the body & chassis assembly. It welds to the main chassis rail to support the ...

Front Sill Panel - Left Hand is a pressed steel body panel that forms the lower left-hand side of the front body section. The panel closes the low...

Plain Washer with a 1/4" bore, used as a general-purpose flat washer. Fitted under a bolt head or nut, it spreads the clamping load over a wider a...

Screw hex HD 3/8" UNC x 1-1/4"

Front Wing Panel is the outer body panel that forms the side of the front end over the front wheel arch, part of the front body assembly. Supplied...

Door Pillar Bracket for the right-hand (offside) bulkhead door pillar, supplied as the bottom bracket only (less the pillar). The bracket forms th...

Exhaust Valve for the 2.6L 6-cylinder IOE (inlet-over-exhaust) petrol engine, forming part of the cylinder head and block valvetrain. The exhaust ...

Mainshaft Nut - castellated nut that retains the assembled components on the rear of the gearbox mainshaft. The castellations accept a split pin to...

Cylinder Head Bolt - a 7/16" UNC x 2.71" medium-type bolt for the Rover V8, part of the cylinder head fixings. This is the medium-length head bolt...

Centre Retainer - Front Windscreen Glass is the metal retainer strip that secures the front windscreen glass at its centre division point. The ret...

Layshaft for the LT76 four-speed gearbox, Suffix A only. It carries the cluster of layshaft gears below the mainshaft, driven by the constant-mesh ...

Conrod Bolt for Land Rover petrol and diesel four-cylinder engines. This bolt secures the connecting rod cap to the connecting rod, clamping the b...

Plain Washer - Large 5/16" is a large plain washer for use with 5/16" fastenings, providing load distribution beneath bolt heads and nuts across La...

Free Wheeling Hub Kit - manual locking front-axle hubs that connect or disconnect the front halfshafts from the road wheels. Set to free, the front...

Clutch push rod

Free-Wheeling Hub Kit - manually operated locking front hubs for a 24-spline front axle, fitted to the front stub axle in place of the standard dri...

Lock Barrel Set - 3 Barrels & Keys for anti-burst door locks in the door locking assembly. This set supplies three matching lock barrels and k...

Winch Remote Control operates an electric recovery winch wirelessly, allowing the operator to stand clear of the winch line during recovery. Wirel...

Autolite Work Lamp - Square - 55W

Distributor Spring Set for the advance mechanism of the Lucas distributor, part of the Distributor & Ignition assembly. The advance springs go...

Manifold Absolute Pressure (MAP) Sensor, part of the engine management system. The MAP sensor measures the absolute pressure inside the intake man...

Union Nut for the fuel pipe in the fuel delivery system. This M12 union nut clamps a fuel pipe to its mating union or component port, drawing the ...

Water Pump - 2.0 IOE - the engine coolant pump in the cooling system, for the 2.0L IOE (inlet-over-exhaust) petrol engine. Driven by the fan belt ...

Engine Stud is a threaded fastening stud used in the cylinder head and manifold assemblies of the four-cylinder engine. It provides the fixed thre...

Cylinder Head Gasket - 2.6L 6-Cylinder seals the joint between the cylinder head and the engine block on the Rover 2.6L inline six-cylinder IOE (in...

Bolt - 7/16" UNF x 1-1/2" imperial hex-head fastener for use in axle, suspension, and body or chassis applications requiring 7/16" UNF imperial thr...

Land Rover Series III Parts Catalogue, an illustrated reprint published by Brooklands Books Ltd. It reproduces the factory parts catalogue for the ...

Rotor Arm for the 24V shielded ignition distributor. The rotor arm mounts on the top of the distributor shaft and, as it rotates, routes the high-t...

Piston Ring Set for the 2.25L and 2.5L 4-cylinder petrol engine, supplying the ring pack for one piston. The rings seat in the piston ring grooves...

Spark Plug - ignites the air/fuel mixture in the combustion chamber of the petrol engine. It threads into the cylinder head with its electrode gap ...

Water Pump O-Ring forms the coolant seal between the water pump and the engine front cover, within the cooling circuit. It seats in the water pump...

Rear Spring Dowel - a locating dowel that positions the rear road spring on its seat. The dowel engages a corresponding hole in the base of the sp...

Pop Rivet (blind rivet) used to secure the flexible door rubber, a body and door-trim fixing. The rivet fastens the flexible rubber seal to the do...

Fuel Tank Drain Plug - the threaded plug that seals the drain point at the base of the fuel tank. Removing it allows the tank to be drained for se...

Steering Box - LHD is the manual steering gearbox at the heart of the steering system. It converts rotation of the steering wheel and column into ...

Metal Fuel Filler Cap seals the fuel tank filler neck, closing the fuel system against contamination, spillage and evaporative loss. The cap secur...