Land Rover Series Parts

Ignition Lead Set for the 3.5L Rover V8 petrol engine, carrying the high-tension spark from the distributor to the spark plugs. The set comprises ...

Oil Filler Plug serving as the combined fill and level check point for the swivel pin housing, manual gearbox gearcase, and LT230 transfer box on L...

Brake Pipe Union for the hydraulic brake system, a female fitting in brass. This union connects a 3/16 inch brake pipe into the brake hydraulic ci...

Differential Carrier Gasket for the Rover-type axle assembly. The gasket seals the differential carrier housing against the axle casing at the cen...

Crankshaft Rear Oil Seal for the engine bottom end, fitted at the rear of the crankshaft where it exits the block towards the flywheel. The seal r...

Split Pin for use in the front and rear suspension assembly of the Series Land Rover. The split pin is inserted through the hole in a castle nut o...

Exhaust Nut in brass, securing exhaust components to their mounting studs. The 5/16" UNF thread and brass construction resist seizing and corrosio...

Nyloc Nut with an M10 thread - the nylon-insert locking nut used on U-bolt fixings. A nylon collar set into the top of the nut grips the bolt thre...

Bolt - fixing bolt with an ACME (trapezoidal) thread form, used to secure the outer front wing to the bulkhead. It fastens the rear mounting flang...

Sealing Washer used at sealing interfaces across multiple engine assembly groups. This washer is used in rocker cover and breather assemblies, val...

Distributor Rotor Arm for the 3.5L V8 petrol ignition system. The rotor arm sits on top of the distributor shaft beneath the cap and rotates to dis...

Fuel pump diesel 2.25

Anti-Roll Bar Washer used at the anti-roll bar and shock absorber mounting. The washer spreads the clamping load of the retaining nut across the m...

Distributor Cap for the ignition distributor on the V8 EFI engine. The cap seats over the distributor and carries the high-tension current from th...

Ignition Coil - high-tension coil in the ignition system. Converts the low-voltage supply into the high-tension voltage required to fire the spark...

Engine Oil - 15W40 Multigrade mineral engine lubricant for older petrol, diesel, and LPG engines. 15W40 multigrade viscosity provides reliable lub...

Copper Sealing Washer used across a wide range of sealing applications on Land Rover vehicles. This soft copper washer provides a reliable, leak-f...

Gear Oil - EP80W90 extreme-pressure gear lubricant for manual gearboxes, transfer cases, and axle drives. The EP80W90 grade combines extreme-press...

Door Hinge Bolt for attaching door hinges to the body structure. This countersunk bolt secures the hinge plate to the hinge assembly, providing a ...

Rear Drum Brake Shoe Set covering one full axle, sized for 11-inch rear drum brakes. The shoes carry the friction linings that press outward agains...

Distributor Module for the 3.5L Rover V8 petrol engine, used with the earlier single-coil electronic ignition system. It forms part of the distribu...

Fuel Filter for the diesel fuel delivery system, separating dirt, debris and water from the fuel before it reaches the injection pump. Fitted in t...

Oil Seal - a radial oil seal fitted between the wheel hub and stub axle within the wheel hub and drive shaft assembly. The seal retains lubricant ...

Self-Locking Nut with a 5/16" UNF thread and a 1/2" across-flats hexagon. The self-locking action resists loosening under vibration, retaining cla...

Captive Nut with a UNF thread, providing a fixed threaded anchor point for a bolted fixing. The nut is retained in its bracket or panel so it cann...

Lights and Heater Toggle Switch - a three-position Lucas-type toggle switch fitted to the dashboard switchgear. It acts as the master control for t...

CuNiFer Brake Pipe, 3/16" outer diameter, supplied for the brake hydraulic circuit. The copper-nickel alloy resists corrosion and is soft enough to...

Universal Joint for the axle half shaft, allowing the shaft to transmit drive through an angle. The joint sits within the half shaft and lets it t...

Ignition Coil for the ignition system of 4-cylinder petrol engines. The coil steps up the low-voltage supply into the high-tension output that fir...

Side Lamp - front side (parking) lamp in the exterior lighting system. Dome-type front side lamp providing position and marker lighting at the fro...

Brake Union for the hydraulic braking circuit, with male 7/16"-20 UNF thread for 1/4" diameter brake pipe. This male-threaded end fitting connects...

Coolant Temperature Sensor - V8 EFI for the engine management system. This sensor monitors coolant temperature and sends a continuous signal to th...

Alternator - charging unit in the vehicle's electrical charging system. Driven from the engine by the accessory belt, it generates current to powe...

Fitment: All models to (VIN) KA930455 All models 1980 on

Inlet Manifold Seal for the V8 petrol induction system, straight pattern. The seal closes the joint between the underside of the inlet manifold an...

Wiper Drive Cable for the windscreen wiper system on cable (rack) type wiper drives. The flexible toothed cable runs inside the wiper rack tubing ...

Flasher Relay installed in the indicator and hazard-warning circuit, controlling the flash rate of the turn-signal lamps. This 12V electronic unit...

Speedometer Cable Plate Screw secures the speedometer cable retaining plate to the gearbox. It clamps the plate that holds the speedometer drive c...

Serrated Washer with a 3/8" bore, a serrated locking (shakeproof) washer. Fitted beneath a bolt head or nut, the serrated teeth bite into both the...

Hex Nut - 1/4" UNF is a plain hexagonal nut with a 1/4 inch UNF thread, used as a general-purpose imperial-thread fastener throughout the chassis, ...

Nut - a plain full hex nut with a 3/8" BSF (British Standard Fine) thread. A general-purpose imperial fastener used at many points across the engi...

Nut - M6 is a plain M6 hexagonal nut used as a general-purpose threaded fastener throughout the chassis, body and mechanical assemblies. It tighte...

Weber Carburettor for the 2.25L petrol engine, part of the fuel and induction system. It meters fuel into the incoming air stream to form the air/f...

Rear Stop/Tail Lamp - combined rear stop and tail lamp, supplied as a complete lens and body assembly. It mounts in the rear lamp position and pro...

Crankshaft Oil Seal - Rear seals the rear of the crankshaft where it leaves the cylinder block at the flywheel end, retaining oil within the bottom...

Oil Seal for the front axle swivel pin housing. Seals the front driveshaft where it passes into the inner end of the swivel housing, retaining axl...

Fuel Pump - Petrol 4-Cyl for the mechanical fuel delivery system on Land Rover 2.25L 4-cylinder petrol engines. This mechanical lift pump is drive...

Toggle Switch is a two-position on/off switch in the dashboard switchgear, controlling the instrument and panel lighting circuit. The sprung toggl...