Land Rover Series Parts

Split Pin used throughout the chassis, steering and driveline assemblies as a positive locking fastener. The pin is passed through a cross-drilled...

Side Cover Gasket sealing the cylinder-block side cover (tappet inspection cover) to the block face on diesel engines. The side cover closes the p...

Swivel Housing Washer for the swivel pin housing drain plug, part of the front axle swivel assembly. The sealing washer fits beneath the drain plu...

Gearbox Mainshaft Oil Seal for the rear of the manual gearbox, sealing the mainshaft where it passes through the rear of the mainshaft-and-gears se...

Front Propshaft for the 4-cylinder 2.25L petrol driveline. It transmits drive from the transfer box front output to the front axle differential, de...

Spark Plug - ignites the air/fuel mixture in the combustion chamber of the petrol engine. It threads into the cylinder head with its electrode gap ...

Drive Pin Fastener is a two-piece push-in fixing used to retain interior trim and ducting panels. The fastener body is pushed through aligned hole...

Nut for U-bolt M12

Brake Pipe Union - a male tube-nut fitting that secures a flared 3/16" (4.75mm) hydraulic pipe end into a female union, T-piece or cylinder port. ...

Centre Cubby Box finished in black vinyl, fitting the centre position between the front seats to provide an enclosed storage compartment with a mou...

Fir Tree Fastener secures interior body and roof trim panels to the vehicle structure. The ribbed, tapered fir-tree shank pushes into a panel hole...

Front Cover Gasket seals the timing cover to the front face of the cylinder block on the V8 petrol engine. It fits between the front cover and the...

Reverse Gear Selector Detent Spring for the manual gearbox selector mechanism. The spring loads the detent ball against the reverse selector shaft...

Handbrake Shoe Set for the transmission-mounted drum handbrake. The shoes expand against the drum at the transfer box output to hold the vehicle w...

Wiper Spindle Kit

Taper Roller Bearing - Diff Pinion - Outer is the outer pinion bearing in the differential final drive assembly, supporting the pinion shaft where ...

Thrust Washer for the upper swivel pin Railko bush, part of the front axle steering swivel assembly. The Railko bush forms the upper pivot bearing...

Shock Absorber Washer for the rear suspension, outer position. This washer fits over the rear shock absorber mounting, seating against the rubber ...

Contact Set for the Lucas 25D distributor in the ignition system of the 2.25L and 2.6L petrol engines. The contact set (breaker points) opens and ...

Locking plate

Bolt, 1/4" BSF x 1", serving as the steering lockstop in the front axle steering assembly. The bolt threads into the swivel housing and is set to l...

Bolt for the suspension mounting. A 7/16" UNF thread bolt of 6.5" length, used at the upper suspension mounting to secure the shock absorber and sp...

Front Side Lamp with a clear lens and LED illumination, mounting in the front lighting position to serve as the side (parking) light. The LED draw...

Water reservoir grommet rubber seal

Brake Pipe Union - a female union fitting for 3/16" (4.75mm) hydraulic brake pipe, with an M10 x 1mm thread. Machined from brass, it threads onto ...

Flange Head Screw, metric M6 x 20 mm. The integral flange beneath the hex head spreads the clamping load over a wider area and helps resist looseni...

Bolt 5/16" UNF x 2" is a hex-head set bolt with a 5/16-inch Unified National Fine (UNF) thread at 24 threads per inch and a 2-inch shank length. I...

Fixing Screw for the front door hinge and check strap assembly. This screw secures the door hinge and the check strap (door-stay) to the body pill...

Rocker Cover Gasket for the V8 petrol engine, cork construction. The gasket seals the joint between the rocker cover and the cylinder head, contai...

Coolant Expansion Tank Cap – the pressure-relief cap that seals the cooling system's expansion (header) tank. Rated to 15 psi, it holds the system...

Relay - 12V automotive changeover relay with a 30A contact rating. The five-pin (SPDT) configuration provides both normally-open and normally-clos...

Hex Head Bolt with a 1/4" BSF thread and a 5/8" shank length. A common application is the swivel pin housing, where it retains the swivel oil seal...

Clutch Cover (pressure plate assembly) for the clutch on 4-cylinder petrol applications. The cover bolts to the flywheel and houses the diaphragm ...

Ball Joint for the anti-roll bar drop link. It forms the pivoting connection at the end of the anti-roll bar, linking the bar to the suspension so ...

Hex Nut, 7/16" UNF, plain steel. This full hex nut secures the door top to the door base on Series models and is used at other 7/16" UNF fixing po...

Jubilee Clip - 60-80mm is a worm-drive hose clip with a 60-80mm clamping range. The band is tightened by a captive worm screw to secure large-bore...

O-Ring for the LT95 combined gearbox and transfer box. It seals one of the shaft and housing joints within the unit, retaining gear oil and prevent...

Heater Control Finger Grip The finger grip fitted to a heater control slider on the heater (HVAC) control panel, operated in the up/down plane. It...

Propshaft Bolt Kit - Rear is a driveline fixing set for securing the rear propeller shaft at its flange connections. The kit provides the correct-...

Set Screw, M8 x 70 mm. A fully threaded hexagon-head fastener in high-tensile steel with a bright zinc-plated finish. Used across a range of chassi...

Glass Fuse rated at 10A, a cartridge-type fuse used in the vehicle electrical system. The fuse seats in the fuse box or an inline fuse holder and ...

Oil Temperature Transmitter for the engine instrumentation circuit. The transmitter threads into the oil gallery and varies its electrical resistan...

Nyloc Nut with an M16 thread - a nylon-insert locking nut used on heavily loaded suspension and driveline fixings. A nylon collar set into the top...

Rear Stop/Tail Lamp - LED - LED combined stop and tail lamp with a red lens, supplied as a complete sealed unit to replace the standard rear stop/t...

Head Gasket Seals the cylinder head to the cylinder block on the pre-TDi 2.25L and 2.5L naturally aspirated and turbocharged diesel engines. It co...

Oil Pump Gasket for the engine lubrication system, sealing the oil pump to its mounting face on the cylinder block. It maintains a leak-free joint...

Water Temperature Sender threads into the cooling system and measures engine coolant temperature, feeding the signal to the dashboard temperature g...

Split Pin Assortment A 280-piece assortment of split pins (cotter pins) in a range of sizes, supplied as a workshop set. Split pins secure castell...