Land Rover Series Parts

Rear Door Hinge Pin Kit in stainless steel - a complete repair set for the rear (side-hung) door hinges, replacing corroded or worn hinge pins toge...

Special Fixing Washer for the hardtop side-frame mounting. Seats over the M8 side-frame mounting stud and under its securing nut, spreading the cl...

Self-Tapping Screw – No. 8 × 5/8 in is a general-purpose fastener for securing body, trim and panel fixings. Being self-tapping, it forms its own ...

Sedimentor Seal for the diesel fuel sedimentor assembly. The sedimentor separates water and sediment from the fuel ahead of the injection system. ...

Front Exhaust Pipe (downpipe) for the 2.25L diesel engine, forming the first section of the exhaust system. The front pipe bolts to the exhaust ma...

Gearbox-Transfer Box Gasket for the LT76 gearbox, sealing the mating joint between the gearbox and the transfer box. The gasket maintains the oil-...

Gearbox Gasket Set for the LT95 four-speed gearbox fitted behind the V8 petrol engine. The LT95 is a combined main gearbox and transfer unit. The ...

Core Plug (cup/expansion plug) seals a casting core hole in the cylinder block, fitted at the rear of the block. It closes the openings left by th...

Dust Cap is the small protective cover that fits over a hydraulic bleed nipple in the braking system. Pushed onto the bleed screw of a brake calip...

Gasket for the front cover of the LT67 gearbox. Seals the front cover plate against the front face of the gearbox housing, preventing transmission...

Track Rod & Steering Damper Bush for the steering linkage, locating the steering damper at its mounting eye. The bush insulates the damper mou...

Distributor Cap mounts at the top of the distributor in the ignition system and carries the segment contacts that route high-tension voltage to the...

Expansion Tank Hose connects the coolant expansion (header) tank into the cooling circuit. It carries coolant between the expansion tank and the r...

Grommet - a rubber panel grommet providing a sealed, protected pass-through for the choke cable and windscreen washer tubing. Fitted into the pane...

Gasket for the carburettor-to-inlet-manifold joint in the induction system of the 2.25L 4-cylinder petrol engine. The gasket fits between the carb...

Core Plug for the cylinder head, sealing a core hole left in the casting during manufacture. It closes the opening left by the casting sand core a...

Steering Box Side Plate Gasket seals the side cover plate against the casing of the manual steering box. It sits between the dowel-located side pl...

Flasher Unit is the 3-pin relay in the direction indicator circuit that switches the turn signal lamps on and off at a regular rate. Wired between...

Windscreen Hinge Bolt is a fixing used to secure the folding windscreen frame hinge to the scuttle. It clamps the hinge mounting at the base of th...

Exterior Door Handle with Lock Barrel and Keys, left-hand (nearside). The complete locking handle for the front door, comprising the external push...

Carburettor Spacer for the petrol engine induction system, fitting between the carburettor and the inlet manifold. It sets the carburettor off the...

Accelerator Pedal Return Spring for the cable-operated throttle linkage. The spring returns the accelerator pedal to its rest position when foot p...

Exhaust Clamp Plate for the exhaust mounting assembly. Three-hole clamping plate that secures the exhaust pipe within the mounting bracket assembl...

Mud Shield for the differential pinion. This pressed shield fits over the differential drive flange, ahead of the pinion oil seal, protecting the ...

Brake Clevis A clevis for the brake drum expander mechanism within the drum braking system. It forms the pinned link between the brake operating r...

Valve repair kit

Gear Lever Locating Pin locates and retains the main gear lever within the manual gearbox. It holds the lever against its pivot so that shift move...

Universal Joint for the propeller shaft, of the 82mm cap-to-cap type. The universal (cardan) joint connects two sections of the propshaft, transmi...

Bulb rated 12V 4W with a small-diameter fitting, part of the vehicle lighting system. This low-wattage bulb suits the small-fitting (Lucas-type) l...

Spring plate

Oil Filter Bowl Bolt Washer - rubber sealing washer for the oil filter bowl centre bolt. Fitted to the centre bolt that retains the oil filter bow...

Wheel Spanner - 24mm for removing and fitting wheel nuts on Land Rover vehicles. This 24mm spanner is sized for the standard wheel nut used across...

Heater Distribution Control Cable - the Bowden cable that links the dashboard heater control to the air-distribution flap in the heater assembly. ...

Steering Wheel Boss in the steering column assembly, providing the mounting interface between the column shaft and the steering wheel. The 48-spli...

Timing Chain for the 2.25L four-cylinder engine, part of the timing drive assembly. Drives the camshaft from the crankshaft sprocket, holding valv...

O-Ring Seal - sealing ring for the steering box rocker shaft. Fitted around the rocker (sector) shaft where it passes through the steering box hou...

Ball Bearing for the transfer box, supporting the output shaft and its output flange. Fitted in the LT230 and NV225 transfer boxes, the bearing lo...

Fan Belt for the engine auxiliary (accessory) drive. Transmits drive from the crankshaft pulley to the water pump, cooling fan and dynamo or altern...

Engine Mounting Rubber (V8) supports the V8 petrol engine on the chassis and isolates its vibration from the bodyshell. The bonded rubber-to-metal...

Drain plug

Locknut for body and trim panel fixings. It seats into a pre-formed aperture in the panel to provide a captive threaded point for the screws or bo...

HT Ignition Lead Set for the 2.25L and 2.5L 4-cylinder petrol ignition system. This set of four high tension leads connects the distributor to eac...

Exhaust Valve Stem Seal for the cylinder head valvetrain. Fits over the exhaust valve stem at the top of the valve guide, metering the oil that pa...

Wheel Nut securing a road wheel to the hub, clamping the wheel against the hub mounting face. M16 internal thread and steel construction, to the s...

Rear Fog Lamp with LED illumination, forming part of the rear lighting assembly, providing a high-intensity red rear light for use in poor visibili...

Front Lamp Guards – a hinged protective guard set for the front exterior lamps. The guards mount over the front headlamps to shield the lenses fro...

Clutch Release Bush for V8 petrol applications, located within the clutch assembly at the rear of the crankshaft. The bush seats in the spigot rec...

Inlet Manifold Joint Washer seals the inlet manifold to the cylinder head. It maintains an airtight joint between the manifold flange and the head...