Land Rover Series Parts

Drive Member - 10-Spline is the drive coupling at the outer end of the axle, forming part of the wheel hub and drive assembly. Its 10-spline inter...

Gaiter Retainer - secures the rubber gaiter around the high-low (transfer) lever on the LT76 gearbox, which carries an integral transfer box. The ...

O-Ring Seal - sealing ring for the steering box rocker shaft. Fitted around the rocker (sector) shaft where it passes through the steering box hou...

Oil Filter for the engine lubrication system of the 2.25L four-cylinder petrol and diesel engine. The filter traps combustion by-products, metal p...

Headlamp Bezel - black finish. The trim ring that surrounds the 7" round headlamp, retaining the lamp unit in the front panel and finishing the hea...

Hex-head screw, 1/4" UNF thread, 3/4" long. Unified Fine (UNF) thread form with a hexagonal head for use with standard imperial spanners and socke...

Spark Plug - ignites the air/fuel mixture in the combustion chamber of the petrol engine. It threads into the cylinder head with its electrode gap ...

Drain plug

Locknut for body and trim panel fixings. It seats into a pre-formed aperture in the panel to provide a captive threaded point for the screws or bo...

Wheel Nut securing a road wheel to the hub, clamping the wheel against the hub mounting face. M16 internal thread and steel construction, to the s...

Strap

Exhaust Valve Guide is pressed into the cylinder head to support and align the exhaust valve. It locates the valve stem so the valve seats squarel...

Reverse Lamp Lens is the clear lens that fits to the rear reverse (reversing) lamp assembly. It seals over the bulb and reflector and diffuses the...

Crankshaft Thrust Washer Pair for the 4-cylinder engine, including the 200 TDi and 300 TDi diesels. The thrust washers sit either side of the centr...

Differential Carrier Bearing is a taper roller bearing that supports the differential carrier within the axle, as part of the crownwheel and pinion...

Brake Pipe Clip secures and routes rigid brake pipes along the chassis within the braking system, holding them in position and guarding against cha...

Exhaust Pipe Clamp

Gear Knob - LT95 is the hand grip fitted to the main gear lever of the LT95 4-speed gearbox. It threads onto the top of the gear lever and provide...

Anti-Burst Door Lock for the left-hand front door, the latch mechanism that secures the door to the body. The latch engages the striker on the doo...

Oil Dipstick - engine oil level gauge for the 4-cylinder engine. Inserts into the dipstick tube to read the oil level in the sump, marked with min...

Tow Ball Step is a rear access step that locates over the tow ball, providing two tread levels to make reaching the rear door, load area or roof ea...

Bolt - threaded fastener with a 7/16" UNF (Unified National Fine) thread and a 2-1/4" length.

Seat Belt Buckle Catch - left-hand front seat belt stalk receiver forming the fixed lower end of the front LH seat belt assembly. The non-audible c...

Bolt with a 5/16" UNF (Unified National Fine) imperial thread and a 1-1/2" shank length. A hex-head fastener for general assembly and fixing appli...

Exhaust Manifold Stud secures the manifold to the cylinder head on the 4-cylinder engine. It threads into the head and carries the manifold flange...

Fuel Pump Repair Kit for overhauling the mechanical diaphragm lift pump on the 2.25 four-cylinder petrol engine. Wear in the pump internals reduce...

Heater Control Valve regulates the flow of engine coolant into the heater matrix, forming part of the cabin HVAC heating circuit. The valve is cab...

Exhaust Clamp Plate for the exhaust system, used at the front-pipe and catalyst joint. The plate works together with a U-bolt to draw the exhaust c...

Inlet manifold stud

Ignition Coil for the V8 petrol ignition system. It converts the low-voltage supply into the high-tension voltage that fires the spark plugs throug...

Screw with a mushroom head and a 1/4" Acme thread, 1" long, with a sherardized zinc finish. Used as a floor fixing, securing the transfer lever ga...

Head Gasket - 3.5L V8 - Metal is the cylinder head gasket for the 3.5L V8 petrol engine, sealing the joint between a cylinder head and the engine b...

Half Shaft – Rear LH – 10-Spline is the rear axle drive shaft for the left-hand side. It transmits drive from the differential out to the rear hub ...

Synchro Cone – LT76 is a synchroniser ring from the synchromesh assembly of the LT76 manual gearbox. It is the friction component that brings the g...

Fuel Cap - Extra Tank - Military

Track Rod & Steering Damper Bush for the steering linkage, locating the steering damper at its mounting eye. The bush insulates the damper mou...

Joint Washer for the radiator cap, part of the engine cooling system. This sealing washer seats between the radiator cap and the filler neck, main...

Radiator Overflow Hose carries coolant overflow away from the radiator filler neck. It connects to the overflow spigot on the radiator filler neck...

Oil Filler Cap O-Ring seals the oil filler cap to the rocker cover. It forms an oil-tight seal at the cap-to-cover joint, preventing oil leakage a...

Injector Pipe - the high-pressure fuel line serving the No.4 cylinder on the 2.25L diesel. It carries metered fuel from the injection pump outlet ...

Fuel Pipe Olive for the fuel supply line. The olive is the compression ferrule that seats between the fuel pipe and its union fitting. When the un...

Gearbox Thrust Washer for the intermediate gear (laygear) in the main gearbox, used on 4-cylinder applications. It locates against the intermediat...

Staple Clamp for the soft top canvas hood, part of the rear body tie-down hardware. Fixed to the rear body side, it forms the anchor loop that the...

Interior Door Lock Button, right-hand, of the interior door furniture. The thumbscrew-type lock button that operates the door lock from inside the...

Sliding Window Catch secures the sliding glass of the front door side window, locking the two panes together so the window can be held shut or fixe...

Rubber Plug Cushion is a moulded rubber blanking plug that fits into a pre-formed aperture in the body, frame or seat base to close off the opening...

Cable Grommet for the wiring loom, fitting a 41.5 mm panel hole and accepting a cable of up to 6 mm. Made of black rubber, it lines the hole where...

Lock Washer for the starting dog at the front of the crankshaft. The starting dog threads into the nose of the crankshaft to retain the front pull...