Land Rover Series Parts

Differential Thrust Washer for the LT230 transfer box centre differential. It bears against the differential gears within the centre differential,...

Piston for the 2.25L four-cylinder diesel engine, forming part of the piston and connecting rod assembly within the cylinder block. Supplied at +0...

Crankshaft Pulley for the 2.25L and 2.5L 4-cylinder petrol engine. It mounts on the nose of the crankshaft and drives the cooling fan, water pump a...

Oil Pressure Sensor Monitors engine oil pressure in the lubrication circuit and signals the oil pressure gauge or warning lamp on the instrument pa...

Steering Wheel - a 14-inch three-spoke replacement wheel with a black vinyl rim and black centre. The wheel mounts to the steering column through ...

Bolt 1/4" UNF x 2-1/2"

Self-Tapping Screw - a No. 8 x 3/8" self-tapping screw used as a general-purpose fixing. The self-tapping thread cuts its own mating thread as it ...

Pinion Lock Nut – Salisbury secures the drive pinion in the Salisbury rear differential, retaining the pinion flange and holding the pinion bearing...

Oil Strainer Gasket for the Rover V8 petrol engine, sealing the flanged joint of the oil pick-up strainer inside the sump. Renew it whenever the p...

Heater Hose – Inlet carries hot coolant from the engine cooling circuit to the heater matrix, forming part of the cabin heating system. The inlet ...

Input shaft oil seal

Rivet is a permanent mechanical fastener used in the lower tailboard (drop-down tailgate) hinge assembly. Set through the hinge components, it for...

Spire Nut is a spring-steel push-on fastener used to retain body panels and trim. The clip slides over a panel edge or hole and self-threads onto ...

Oil Pump Gear for the 3.5L V8 engine oil pump, part of the lubrication system. The oil pump draws oil from the sump and pressurises it for deliver...

Carburettor Grommet for the twin Stromberg carburettor installation on the V8 petrol engine. It sits in the air cleaner and carburettor air intake ...

U-Bolt – Rear – 1-Ton clamps the rear leaf spring to the axle. The U-shaped bolt passes over the axle and through the spring seat plate, where its ...

Half Shaft – Rear RH – 10-Spline Short is the rear axle drive shaft for the right-hand side. It carries the drive from the differential out to the ...

Oil Filler Cap Assembly for the rocker (valve) cover of the 2.25L 4-cylinder petrol engine. The cap seals the oil filler neck and incorporates an i...

Clutch Lever Clip that retains the clutch release lever on its pivot post within the gearbox bellhousing. The clip holds the release fork onto the...

Valve Guide A precision sleeve pressed into the cylinder head that supports and locates the inlet valve stem, holding the valve concentric with its...

Injector Pipe No.3, a high-pressure delivery pipe in the diesel fuel injection system. The rigid steel pipe carries fuel under high pressure from ...

Injector Pipe No.1, a high-pressure delivery pipe in the diesel fuel injection system. The rigid steel pipe carries fuel under high pressure from ...

Core Plug seals a casting aperture in the cylinder block or head of the 2.25L and 2.5L four-cylinder petrol engines. Also known as an expansion or...

Differential Pinion Bearing Spacer used in the axle differential assembly across a broad range of Land Rover models from 1965 onwards. This spacer...

Differential Pinion Inner Taper Roller Bearing used in the differential pinion shaft assembly within the axle final drive. The bearing supports th...

Exhaust Downpipe is the front section of the exhaust system, connecting the exhaust manifold outlet to the intermediate pipe. This downpipe fits L...

Heater Cable operates the tap-type heater control valve in the heating and ventilation system. It connects the dashboard heater control to the tap...

Rubber Seal fits along the joint between the truck cab base and the rear body, sealing where the cab meets the tub. It forms a continuous barrier ...

Rear Door Seal - rubber weatherseal for the rear door aperture. This rubber seal fits around the rear door opening, sealing the closed door agains...

Hoodstick Bracket Clamp - secures a hoodstick to its mounting bracket within the soft-top frame. The clamp holds the hoodstick (the soft-top frame...

Shim is a 0.002" adjustment shim for the manual (non-power-assisted) steering box. It is fitted within the steering box to set the correct end-flo...

Shock Absorber Bolt secures a shock absorber to its mounting in the suspension. The long shank passes through the damper eye and mounting bracket ...

Clutch Anchor Plate - a steel mounting plate within the clutch pedal box assembly. It anchors the clutch pedal pivot to the bulkhead, providing th...

Exhaust Bracket for the exhaust system on left-hand drive vehicles. This bracket supports and locates the exhaust along its run beneath the vehicl...

Washer used at multiple points within the manual gearbox assembly, including the main casing, extension housing, oil pump and speedometer drive hou...

Clevis Pin - pivot pin used in the mechanical brake and transmission linkages. It passes through a forked clevis and the eye of a mating rod or lev...

Hot Plug - 2.0L & 2.25L Diesel

Exhaust Valve - the poppet valve that seals the exhaust port in the cylinder head and opens on the exhaust stroke to release spent combustion gases...

Shock Absorber for the front suspension, a heavy-duty oil-filled hydraulic damper. Mounted between the axle and the chassis, it damps the oscillat...

Copper Washer is a soft sealing washer used to form a leak-tight metal seal at a threaded or banjo union. Positioned between a bolt or fitting and...

Bulb 24V 21/5W dual-filament bulb for 24-volt electrical systems. The 21W filament serves the stop light circuit and the 5W filament serves the tai...

Steel ball 1/4"

Upgrade your Land Rover Defender (1987-2006, 2007-2016) or Series 3 with the WIPAC LED 73mm smoked lamp kit. Smoked LED style light for a sleek...

Front Towing Eye / Lifting Ring bolts to the front of the chassis, providing an anchored attachment point for towing, recovery and lifting. The ri...

Crankshaft Timing Chain Sprocket The drive sprocket mounted on the nose of the crankshaft within the timing chain drive of the Rover V8 petrol engi...

Centre floor mounted storage cubby box providing an enclosed compartment between the front seats and additional cup holder provision within the int...

Tow Ball 50mm flange-fixing tow ball for use with a bolt-on tow bar drop plate. Rated for a maximum gross trailer weight of 3.5 tonnes, with a D-v...

Antiluce Cotter Pin for the tailgate assembly. This self-locking drop fastener secures the rear door capping fixing, retaining the tailgate hardwa...