Land Rover Series Parts

Water Pump for the engine cooling circuit of the 2.5L 4-cylinder naturally aspirated diesel, petrol and pre-TDi turbo diesel engines. Belt-driven f...

Snatch Block - a winch recovery pulley used to redirect a winch line or to double its effective pulling capacity. Rated for a 10-tonne working load...

Hex Head Bolt - 1/4" UNF thread, 5/8" long, with a hexagonal head. A general-purpose imperial fastener with a Unified Fine (UNF) thread form, driv...

Mirror Glass - the replacement reflective glass for the exterior door mirror. It seats into the mirror head on its backing plate, restoring a clear...

Piston Ring Set for the 2.25L and 2.5L naturally aspirated diesel engine, supplying the ring pack for one piston. The rings seat in the piston rin...

Piston for the 2.25L 4-cylinder petrol engine, forming the reciprocating member within the cylinder bore that transmits combustion pressure through...

Brake Shoe Screw - a retaining screw within the drum brake assembly that secures the brake shoe in position. It holds the shoe located against the...

Wiper Cable Tube - LHD is a guide tube in the cable-and-rack windscreen wiper system, in the left-hand-drive configuration. It houses and routes t...

Clevis Pin for the handbrake (transmission parking brake) linkage. This 22mm clevis pin connects the handbrake operating rod to the relay lever, t...

Brake Hose is a flexible hydraulic line in the braking circuit, carrying fluid from the rigid chassis-mounted brake pipe to the caliper or wheel cy...

Accelerator Cable for the throttle control linkage, transmitting accelerator pedal movement to the carburettor throttle on the 2.25 litre petrol en...

Exhaust Y-Pipe is the front section of the exhaust system, merging the outlets from both cylinder banks of the 3.5L V8 petrol engine into a single ...

Side Window Seal is the rubber glazing seal that secures and weatherproofs the fixed side window glass within its body aperture. Part of the body ...

Door Seal - Bottom for the left-hand front door, forming part of the door-aperture weather sealing. The seal fits along the lower edge of the door...

Spare Wheel Bonnet Buffer is a rubber buffer for the bonnet-mounted spare wheel carrier. It sits between the spare wheel and the bonnet, cushionin...

Rear Main Bearing Cap Seal for the Rover V8 petrol engine, sealing the joint between the rear main bearing cap and the cylinder block. This crucif...

Rear Stop/Tail Lamp - LED, Smoked - LED combined stop and tail lamp with a smoked lens, supplied as a complete sealed unit to replace the standard ...

Nut - 10/32" UNF A nut with a #10-32 UNF (Unified National Fine) internal thread, run onto a matching UNF bolt or stud to clamp the joint.

O-Ring - LT95 Gearbox seals the transfer shaft on the LT95 4-speed gearbox, which carries an integral transfer case, preventing oil leakage at the ...

Swivel Pin Housing for the front axle, the chrome-finished swivel joint on which the steering swivel and hub assembly pivot. The housing bolts to ...

Bolt is an M8 x 80 mm threaded fastener used to clamp two components together at a bolted joint. It is tightened into a threaded hole or secured w...

Rubber-Lined Sealing Washer - a metal sealing washer with a bonded rubber lining, fitted under a bolt or union to seal the joint. As the fitting i...

Inlet Valve for the 2.25L and 2.5L four-cylinder diesel engines, including the 2.5L Turbo Diesel, operating in the cylinder head valve train. It o...

Piston for the 2.25L four-cylinder diesel engine, operating within the cylinder block as part of the piston and connecting-rod assembly. The pisto...

Breather and oil filler cap for the rocker cover, part of the engine crankcase ventilation system on the 2.25L and 2.5L 4-cylinder petrol and natur...

Inlet to Exhaust Manifold Gasket - 2.25/2.5 Petrol

Valve Stem Seal - the seal fitted over the valve stem in the cylinder head to control the oil that passes down the stem into the port. This is the...

Exhaust Valve for the cylinder head of the 2.25L 4-cylinder petrol engine, with a 35mm head diameter and a single collet groove on the stem. It se...

Hydraulic Tappet fitted within the V8 petrol engine valve train, where it maintains zero valve clearance automatically. Engine oil pressure fills ...

Connecting Rod Nut - the big-end nut that secures the connecting rod cap to the rod bolts. The nut clamps the connecting rod bearing cap onto the ...

Number Plate Mounting bracket for securing a front number plate, measuring 405mm wide by 110mm deep. The bracket provides a flat mounting face for ...

Panhard Rod Bolt with a 1/2" UNF (Unified National Fine) imperial thread and a 3-1/4" shank length, manufactured to a high-tensile grade. Secures ...

Color of the pin may differ.

Spare Wheel Cover for an externally mounted spare wheel sized 7.50x16 (235/85R16). Constructed from soft vinyl, it shields the spare wheel and tyr...

Blanking Plug for closing a 1-5/8" hole in bodywork or panels. Seals an unused aperture or grommet hole in body panels, brackets and pedal/electri...

Seat belt bracket RH

Drive Screw - a No. 6 x 5/8" self-tapping drive screw used as a body fixing. It retains the grille assembly and secures the rear door and tailgate...

Carb overhaul kit 175CD V8 Zenith Stromberg

Oil Seal - Clutch Cross Shaft for Series 1 and Series 2 Land Rover vehicles (1948-1971). The clutch cross shaft passes through the bellhousing and...

Diff Pinion Taper Roller Bearing is the inner pinion taper roller bearing in the Salisbury axle differential. It supports the pinion shaft where i...

Cup Plug (core plug) for the front face of the Rover V8 cylinder head. This pressed-steel cup plug seals the front casting gallery in the Rover 3....

Core Plug for the engine casting. Core plugs seal the core holes left in the cylinder block after the casting sand is removed during manufacture. ...

Driving Member is the front hub drive flange that couples the axle halfshaft to the road wheel hub. It bolts to the outer face of the front hub, w...

Brake Pedal Return Spring for the pedal box assembly, fitted to servo-assisted braking systems. The spring returns the brake pedal to its rest pos...

Manifold Clamp - a clamping plate that secures the manifold to the cylinder head. It fits over the manifold flange and draws down onto the cylinde...

Push Rod for the petrol-engine valve train. Each push rod transfers motion from the camshaft follower to the rocker arm to open the valve. Fitted ...

Clevis Pin for the clutch cross shaft, part of the mechanical clutch release linkage. The pin forms the pivoting joint that connects the clutch op...

Crankshaft Oil Seal is the outer (rear) crankshaft seal in the engine sealing arrangement, fitted where the crankshaft exits the cylinder block. S...