Land Rover Series Parts

Gasket and Seal Kit for the LT230 transfer box, supplying the gaskets and seals needed to reseal the casing on overhaul. Used when the transfer bo...

Hylomar Hylosil 100 is a neutral-curing RTV silicone sealant for gasketing, sealing and bonding in automotive and engineering applications. It cure...

Clutch Slave Cylinder is the hydraulic actuator in the clutch release circuit, mounted externally on the gearbox bellhousing. When the clutch peda...

Stop/Tail Light Bulb - 12V 5/21W (trade reference 380) for rear lamp assemblies. This dual-filament bayonet bulb (BAY15d base) provides 5W tail li...

Headlamp for the front lighting system: a 7-inch round unit with a flat glass lens. The lamp takes a replaceable H4 halogen bulb, giving combined ...

Fuel Tank Sender Sealing Ring for the fuel tank sender unit assembly. This sealing ring provides the fuel-tight seal between the fuel level sender...

Nyloc Nut with a 3/8" UNF thread and a 12 mm across-flats hex, in the full-height (thick) form. A nylon insert set into the crown of the nut defor...

Sump Gasket for the Rover V8 petrol engine oil sump assembly. This gasket is fitted between the oil sump (oil pan) and the engine block, forming a...

Clutch master cylinder for the hydraulic clutch system. This component converts pedal movement into hydraulic pressure, supplying fluid to the cl...

Wiper Blade for the front windscreen, with a stainless steel frame. The blade clears the driver's field of view across the front windscreen. It at...

Front Hub Nut for the front hub and driveshaft assembly, retaining the wheel hub and bearing assembly on the stub axle. This large-diameter locknu...

Shock Absorber Bush is a rubber mounting bush that fits into the shock absorber mounting eyes, locating the damper at its chassis and axle attachme...

Door Hinge Shim for the Land Rover door hinge assembly. This 1mm shim is fitted between the door hinge and its mounting face to set or adjust the ...

Fuel Filter for the diesel fuel delivery system, separating dirt, debris and water from the fuel before it reaches the injection pump. Fitted in t...

Front Cover Oil Seal

Oil Filter for the engine lubrication system of the 2.25L four-cylinder petrol and diesel engine. The filter traps combustion by-products, metal p...

Fuel Tank Sender Locking Ring for the fuel tank sender unit assembly. This ring secures the fuel level sender unit in position within the fuel tan...

Flasher lamp OEM WIPAC fits front and rear

Glass Fuse - 35A cartridge fuse for the electrical system. A glass-bodied fuse rated at 35A that protects a wiring circuit against overcurrent; th...

Differential Pinion Oil Seal for the axle differential housing. This oil seal fits around the pinion flange where the propshaft coupling connects,...

HT Ignition Lead Set for the 2.25L and 2.5L 4-cylinder petrol ignition system. This set of four high tension leads connects the distributor to eac...

Rear Reflector mounts in the rear lamp area as part of the rear lighting and signalling assembly. A passive retroreflector that returns incident l...

Oil Seal for the swivel pin housing on the front axle, sealing against the polished surface of the swivel ball. The seal seats in the rear face of...

Clutch Release Staple is the spring retaining clip that secures the clutch release bearing assembly to the clutch fork, holding the bearing in posi...

Tap screw

Windscreen Washer Jet directs washer fluid onto the windscreen as part of the front wash/wipe system. This single jet is bulkhead-mounted and fed ...

Pinion Seal - Salisbury Axle seals the nose of the pinion shaft at the front of the Salisbury differential housing, where the propshaft coupling fl...

Track Rod End Boot - Polyurethane for the steering track rod end ball joint. This polyurethane boot fits over the track rod end housing, sealing t...

Shock absorber bush (eye), anti roll bar bush

Hylomar Universal Blue is a non-setting gasket jointing compound for use on gaskets and machined metal joint faces in automotive and engineering ap...

Inlet Manifold Gasket for the V8 petrol engine, forming the seal between the central inlet manifold casting and the cylinder head intake faces. It...

Lights and Heater Switch - a three-position Lucas-type toggle switch fitted to the dashboard switchgear. It acts as the master control for the exte...

Sealing Washer for diesel fuel injectors, positioned at the injector nozzle seat in the cylinder head to seal against combustion gases around the i...

Universal Joint for the propeller shaft, of the 82mm cap-to-cap type. The universal (cardan) joint connects two sections of the propshaft, transmi...

Lock nut 3/8" BSF

Hex Nut - 3/8" UNF - Full is a full-height plain hexagonal nut with a 3/8 inch UNF thread, used as a load-bearing imperial-thread fastener. It is ...

Differential Pinion Oil Seal for the axle differential housing. This oil seal fits around the pinion flange where the propshaft coupling connects,...

Exterior Mirror with convex glass and a black finish, supplied as a complete door-mounted mirror assembly. The convex glass gives a wider rearward...

Oil Pressure Switch for the engine lubrication system warning circuit. This pressure-sensitive switch threads into the engine block oil gallery an...

Headlamp Bowl Kit for the 7-inch headlamp assembly on Series III and Defender vehicles. This kit comprises the plastic headlamp backing bowl and t...

Joint Washer - front timing cover gasket for Land Rover 4-cylinder petrol and diesel engines. This gasket seals the mating face between the front ...

Copper Injector Sealing Washer in the fuel injection assembly of pre-TDi Land Rover diesel engines. This copper washer seats beneath the injector ...

Instrument Voltage Stabiliser - a thermal bimetallic unit mounted on the back of the instrument cluster that regulates the supply voltage to the fu...

Drive Flange Gasket

Drum Brake Shoe Set covering one full axle. The shoes carry the friction linings that press outward against the brake drum to slow the wheel when t...

Side Repeater Lamp - Front is part of the exterior lighting system, mounting in the front wing to give a side-on indication of the direction indica...

Differential Carrier Gasket for the Rover-type axle assembly. The gasket seals the differential carrier housing against the axle casing at the cen...

Locknut for body and trim panel fixings. It seats into a pre-formed aperture in the panel to provide a captive threaded point for the screws or bo...