Land Rover Series Parts

Inlet Valve for the cylinder head of the 2.25L 4-cylinder petrol engine, with a 44.5mm head diameter. It seats in the inlet port of the combustion...

Seat Box End Panel - Right-Hand is a repair panel forming the outer end face of the seat box assembly. It replaces the corroded offside end panel ...

Door Pillar Repair Bracket for the front right-hand (offside) door pillar. A welded repair section that renews the front door pillar at the bulkhe...

Electronic Distributor for the ignition system of the 4-cylinder petrol engine. It distributes high-tension voltage from the ignition coil to each...

Differential Bearing for the Salisbury axle. It is one of the pair of taper roller bearings that carry the differential carrier - the housing holdi...

Exhaust Valve for the cylinder head valvetrain of the 2.25L and 2.5L naturally aspirated 4-cylinder diesel engines. The valve seals against its se...

Circlip for the handbrake (parking brake) linkage. This external retaining circlip secures the handbrake relay elbow onto its pivot post, holding t...

Con Rod Bearing Set - connecting rod big-end bearing shells for the 2.25L four-cylinder engine. The con rod bearings sit between the connecting ro...

Number Plate Lamp for the rear number plate lighting circuit. This complete lamp assembly mounts at the rear of the vehicle to illuminate the numb...

Spring Washer for use across a wide range of fixings and assembly applications on Land Rover vehicles. This split-ring spring washer is placed ben...

Flywheel Bolt, 7/16" UNC x 1" hexagonal head, securing the flywheel to the rear crankshaft flange. Used on V8 petrol engines with manual transmiss...

Hex Bolt - a hexagonal-head bolt with an M6 metric thread and a 12 mm length, manufactured to property class 8.8. Class 8.8 is a medium-carbon ste...

Pan Head Screw - a machine screw with a low, rounded-top head and a flat bearing face, used as a general-purpose fixing. Metric M5 thread with a 1...

Differential Cover for the Salisbury rear axle. The cover bolts to the rear face of the axle casing, enclosing the crown wheel and differential and...

Diesel startermotor military reconditioned EXCHANGE!!

Rotor Arm - Ducellier Type for the ignition distributor assembly. This rotor arm fits the Ducellier-type distributor and rotates inside the distri...

Lock Washer secures the retaining hardware on the layshaft (countershaft) within the manual gearbox. A tab on the washer is folded against the ret...

Mainshaft Peg is a locating peg fitted to the mainshaft of the LT67 gearbox. It positions and retains its associated component on the gearbox main...

Con Rod Bearing Set - connecting rod big-end bearing shells for the 2.25L four-cylinder engine. The con rod bearings sit between the connecting ro...

Split Pin: a cotter pin that locks a slotted (castle) nut or retains a clevis pin. After fitting, its legs are bent back to stop the fastening work...

Hex nut

Plate - LH is the rear axle brake pipe shield (bracket) for the left-hand side. It mounts on the rear axle and shields the rigid brake pipe runnin...

Plate - RH is the rear axle brake pipe shield (bracket) for the right-hand side. It mounts on the rear axle and shields the rigid brake pipe runni...

Blind Nutsert (M6) is a threaded insert that provides an M6 female thread in thin sheet metal or panels where the rear face is not accessible. It ...

Glazing felt strip for the door top sliding glass channel. The felt lines the channel the sliding glass runs in. It cushions the pane, takes up th...

Tailgate Hinge for the left-hand side, the lower hinge on which the drop-down tailboard pivots. It carries one side of the tailboard along its low...

Tailgate Hinge for the right-hand side, the lower hinge on which the drop-down tailboard pivots. It carries one side of the tailboard along its lo...

Seat Base Cushion for the inner (centre) position of the 3-person front bench seat assembly. Constructed with a foam core upholstered in black vin...

Washer is a plain flat washer used as a general-purpose load-spreading fastening component, with a 6 mm internal diameter and a 15 mm outside diame...

Body is the right-hand sill channel for the Defender, running along the underside of the door aperture in the body structure. This structural chan...

Locking Plate - the lower tailboard locking plate, mounted to the rear body. Fitted at the lower hinged tailboard, the plate provides the fixed en...

Flanged Bolt - an M6 x 25mm hexagon-head bolt with an integral flange formed beneath the head. The flange provides a wide bearing face that spread...

Stub Axle - rear stub axle carrying the hub and bearings at the rear axle. Bolted to the rear axle casing, it forms the fixed spindle on which the...

striker lock LH for "anti-burst" locks. (lift-up type)

Electronic Conversion Kit - electronic ignition conversion for the 4-cylinder petrol points distributor. Replaces the contact breaker points and c...

Gasket

Crankshaft Oil Seal - Rear seals the rear of the crankshaft where it leaves the cylinder block at the flywheel end, retaining oil within the bottom...

Rocker Shaft - the hollow shaft that carries the rocker arms in the valvetrain, mounted across the cylinder head rocker pedestals. The rocker arms...

Coolant Hose for the V8 carburettor petrol engine cooling circuit. It carries engine coolant between components of the cooling system, moulded to s...

Steering Wheel is a 15-inch three-spoke replacement wheel that mounts to the steering column. It is supplied without a boss, so a separate fitting...

Mirror Head is a large replacement exterior door-mirror head measuring 265mm x 160mm, offering an increased field of view over the standard head. ...

Spare Wheel Carrier is a fixed rear-door-mounted bracket that supports and retains the spare wheel. It bolts directly to the rear door and locates...

Bolt with a 3/8" UNC (Unified National Coarse) imperial thread and a 2" shank length. A hex-head fastener used in body, chassis and general assemb...

Shock Absorber Washer Retaining washer for the rear shock absorber lower mounting. Part of the rear suspension assembly, it locates over the lower...

NAS Indicator Light - LED Clear 95mm - a single 95mm LED indicator lamp with a clear lens, designed to NAS (North American Specification) lamp dime...

Screw – a black self-tapping screw with a pan head and Pozidriv drive recess, size No. 10 × 5/8 in, used to secure body, trim and panel fixings. B...

Camshaft Bearing, the front bearing in which the camshaft front journal runs within the cylinder block. It supports the forward end of the camshaf...

Mainshaft peg