Land Rover Series Parts

Spring Washer fitted under a nut or bolt head to resist loosening from vibration. An M8 split-ring (single-coil) spring washer. The sprung opening...

Low Note Horn, a 335 Hz electric horn within the audible warning circuit. Produces the low-frequency tone of a dual-tone horn arrangement, pairing...

Windscreen Washer Pump, 12V electric, for the windscreen washer system. The pump draws screen-wash fluid from the washer reservoir and delivers it ...

Clutch Hose - flexible hydraulic line in the clutch actuation circuit. Carries hydraulic fluid from the rigid pipe run to the clutch slave cylinde...

Oil Seal - a radial oil seal fitted between the wheel hub and stub axle within the wheel hub and drive shaft assembly. The seal retains lubricant ...

Spire Clip used to retain front wing panels and heater assembly components. This spring-steel clip slides over a screw or stud thread and grips se...

Air Intake Hose for the 2.25L and 2.6L petrol induction system. This flexible rubber hose connects the air filter housing to the carburettor intak...

Carburettor Manifold Gasket for the 2.25L petrol and carburettor-equipped Defender engines. This gasket seals at the interface between the carbure...

Drive Shaft Oil Seal - Front, fitted at the front axle swivel pin housing. This radial lip seal runs on the front driveshaft where it passes throu...

Worm-drive Hose Clip with a 32-50 mm clamping range, used to secure a flexible hose to a rigid pipe stub or spigot. Tightening the worm screw draws...

Gearbox Front Cover Oil Seal for the manual gearbox front cover, sealing around the primary (input) shaft. Retains gearbox oil and excludes dirt a...

Reverse Lamp Bulb - a 21W 12V single-filament incandescent bulb (type P21W) with a BA15s single-contact bayonet cap, fitted to the rear lamp assemb...

Fuel Tank Spill Return Pipe Gasket for the fuel tank assembly. This gasket seals the joint where the spill return pipe meets the fuel tank, preven...

Wheel Nut securing a road wheel to the hub, clamping the wheel against the hub mounting face. M16 internal thread and steel construction, to the s...

Drum Brake Shoe Set covering one full axle. The shoes carry the friction linings that press outward against the brake drum to slow the wheel when t...

Zenith Carburettor Overhaul Kit for the Zenith 36IV carburettor on 4-cylinder petrol engines. This is the complete overhaul kit for the Zenith 36I...

Transmission Brake Dust Cover for the central handbrake drum on the transmission output shaft. This cover shields the handbrake drum and brake sho...

Brake Shoe Spring for drum brake assemblies. This return spring draws the brake shoes away from the drum surface when the brake pedal is released,...

Exhaust Nut in brass, securing exhaust components to their mounting studs. The 5/16" UNF thread and brass construction resist seizing and corrosio...

Split Pin locks a castellated (slotted) nut in place, passing through the nut slots and a cross-drilled hole in the shaft to stop the nut working l...

Ignition Condenser for the contact-breaker (points) ignition system, mounted at the distributor. The condenser is a capacitor wired across the con...

Rear Stop/Tail Lamp - combined rear stop and tail lamp, supplied as a complete lens and body assembly. It mounts in the rear lamp position and pro...

Upgrade your Series Land Rover suspension with this Polyurethane Shock Absorber Bush Set in black. The set includes 4 pieces, providing everything ...

Rubber Sealing Ring for gear selector shafts in the LT76 gearbox and LT95 transfer box. In the LT76 gearbox, two rings are fitted per unit, sealin...

Oil Filler Plug serving as the combined fill and level check point for the swivel pin housing, manual gearbox gearcase, and LT230 transfer box on L...

Universal Joint for the propshaft, transmitting rotational drive between shaft sections while accommodating the angular movement of the driveline. ...

Salisbury Joint Washer for the Salisbury rear axle differential. The gasket seats between the differential carrier and the axle casing, sealing th...

Number Plate Lamp - LED for the rear number plate lighting circuit. This LED lamp assembly is a direct replacement for the standard incandescent n...

Nyloc Nut with an M10 thread - the nylon-insert locking nut used on U-bolt fixings. A nylon collar set into the top of the nut grips the bolt thre...

Door Seal for the rear end door, fitting along the lower floor edge of the side-hinged tailboard. It forms the sealing interface between the foot o...

Brake Shoe Spring for the drum brake assembly on Land Rover vehicles. This return spring pulls the brake shoes back from the drum face after each ...

Brake Pipe Union for the hydraulic brake system, a female fitting in brass. This union connects a 3/16 inch brake pipe into the brake hydraulic ci...

Crankshaft Rear Oil Seal for the engine bottom end, fitted at the rear of the crankshaft where it exits the block towards the flywheel. The seal r...

Inlet Manifold Gasket - Diesel for the 2.25L and 2.5L 4-Cylinder diesel engine. Fitted between the inlet manifold and the cylinder head, this gask...

Glow Plug Conversion Kit for the 2.25L diesel engine, replacing the original series-wired heater plugs with parallel-wired glow plugs. In the origi...

Drain Plug for differential casings and LT230 transfer boxes. The tapered plug seals the oil drain, fill, and level holes in differential and axle...

U-Bolt Nut - 7/16 BSF for use in the leaf spring suspension assembly. U-bolts clamp the leaf spring pack to the axle casing at the front and rear ...

Axle Key Washer for the hub nut locking system in the axle assembly. This tab washer seats beneath the axle hub nut, with tabs that locate into ma...

Brake & Clutch Master Cylinder - Combined CV-Type serves both the braking and clutch hydraulic circuits from a single unit. In this CV-type de...

Distributor Cap for the ignition distributor on the V8 EFI engine. The cap seats over the distributor and carries the high-tension current from th...

Brake Pipe Union - a male union fitting for 3/16" (4.75mm) hydraulic brake pipe, with a 7/16"-20 UNF thread. It clamps the flared pipe end against...

Exhaust Manifold Gasket for the 3.5L V8 petrol engine. This gasket seals the joint between the exhaust manifold and the cylinder head, preventing ...

Pinion Oil Seal sealing the drive pinion shaft where it enters the Salisbury rear differential. Fitted at the nose of the differential housing, th...

Grommet

Gear Oil - EP80W90 extreme-pressure gear lubricant for manual gearboxes, transfer cases, and axle drives. The EP80W90 grade combines extreme-press...

Instrument Bulb - 12V 2.2W for the instrument panel. Replacement dial illumination bulb for the speedometer on Range Rover Classic Police Vehicle ...

Fuel Filler Breather Hose

Rear brake drum installed in the rear drum brake assembly of the vehicle braking system. The drum mounts to the rear hub and rotates with the wheel...