Land Rover Series Parts

Low Note Horn, a 335 Hz electric horn within the audible warning circuit. Produces the low-frequency tone of a dual-tone horn arrangement, pairing...

Spare Wheel Carrier - a swing-away rear carrier that takes the spare wheel off the rear door and transfers its weight into the body structure, reli...

Gasket Set

LED rear light upgrade kit, 95mm - replaces the round 95mm rear lamp units in the rear lighting circuit with sealed LED equivalents. The lamps are...

Emergency Bulb and Fuse Kit - 12 volt, for vehicles using H4 headlamp bulbs. A compact set of replacement bulbs and fuses to carry in the vehicle,...

Tow Hitch for the towing system, rated to a maximum gross towing weight of 3,500 kg. The hitch bolts to the tow bar and carries the tow ball, prov...

Brushed Stainless Steel Door Thresher E

Door sill panels in stainless steel, covering the outer sill rail below the front door apertures. Supplied as a pair. The sill is the exposed body...

Door sill panels in stainless steel, covering the outer sill rail below the front door apertures. Supplied as a pair. The sill is the exposed body...

Driving Lamps Pair 8 Inch Black

Rear Door Glass Fitting Kit - the fitting components used when installing or refitting the glass in the rear door, sealing and retaining the glass ...

Rear Seat Assembly - full-width rear bench seat for the long-wheelbase rear load area. This is the elongated 1,200 mm bench pattern, mounted trans...

LWB Rear Seat Assembly

Wind Deflector Set - a two-piece set of side window deflectors for the rear side doors. Each deflector mounts to the outside of the door frame alo...

Hood Stick Set - the tubular frame that supports a full-length canvas tilt over the rear load area of a soft-top body. The sticks locate between t...

Chubby Box Techno

Towing Bracket Slider Lock Pin is the pin that locks the vertical slider of a Dixon Bate adjustable-height towing bracket at the selected height. ...

Rear Door Chequer Plate - protective chequer-plate panel for the outer face of the rear door. The plate is fitted to the exposed lower/outer skin ...

Kick Panels - moulded interior trim panels for the footwell area, supplied as a pair. The panels fit against the lower bulkhead on either side of ...

Stainless Steel Rear Door Hinge for the rear end (tailgate) door, supplied as a replacement for the original hinge which corrodes and seizes over t...

Door Hinge Kit - 2nd Row - second row door hinge and pin set with fixings, forming part of the door mounting hardware. Each hinge bolts to the bod...

2nd Row Door Hinge Set - replacement hinges for the second-row side doors, finished in black anodising. Supplied as a set of four hinges complete ...

Door Hinge Kit - Front - front door hinge and pin set with fixings, forming part of the door mounting hardware. Each hinge bolts to the body pilla...

Door Hinge Kit - 2nd Row - Stainless Fixings - a complete set of second row door hinges with fixings, forming part of the door mounting hardware. ...

Door Hinge Pin Kit - Stainless Steel - renewal hardware for the door hinge pivots. The hinge pin is the wearing part of a door hinge: as the pin a...

Front Door Hinge Set - Aluminium - replacement hinges forming the pivot between the front row doors and the A-post. The original hinge castings co...

Light Kit is a complete exterior lamp set of 73 mm round lamps covering the front side, indicator and rear stop/tail positions in one package. The...

Clutch Release Bearing installed within the Clutch & Flywheel Assembly, operating between the clutch release fork and the clutch cover diaphrag...

Differential Thrust Washer for the LT230 transfer box centre differential. It bears against the differential gears within the centre differential,...

Thermostat - 88°C for the cooling system of V8 petrol engines. The thermostat regulates coolant flow between the engine block and the radiator, al...

Seal - Oil Pump

Valve Spring - V8 is a cylinder head valve spring for the Rover 3.5L and 3.9L V8 petrol engine. The valve spring seats between the cylinder head a...

Flywheel Bolt securing the flywheel to the rear flange of the crankshaft. Used on four-cylinder petrol and diesel engines, including the 200TDi an...

Glow Plug for the diesel cold-start pre-heating system, threaded into the cylinder head to project into the combustion chamber (or pre-combustion c...

Exhaust Manifold Locking Washer that secures the exhaust manifold fixings to the cylinder head. The tab washer fits under the manifold bolt or nut...

Core Plug (Cup Type) for sealing the core holes left in the engine block casting after the sand cores are removed during manufacture. The cup-shap...

Camshaft Retaining Plate for the four-cylinder engine. Bolted to the front face of the cylinder block behind the camshaft gear, it locates the cams...

Tube

Seatbelt Mounting for the second-row seats, manufactured in stainless steel and supplied as a pair. Provides the anchorage point for the rear seat...

Firtree Clip - a push-in fastener with a ribbed, fir-tree profile that grips into a pre-drilled panel hole. Used to secure trim panels, wiring loo...

Spacer - Hinge

LED Direction Indicator Lamp - Smoked is a rear direction indicator lamp to NAS (North American Specification) pattern in the 95mm round format, fi...

Pinion Seal - Salisbury Axle seals the nose of the pinion shaft at the front of the Salisbury differential housing, where the propshaft coupling fl...

Camshaft Bearing Kit