Land Rover Series Parts

Mudguard - Power Take Off for the centre power take-off (PTO) housing. Mounted to shield the centre PTO unit from mud, water and road debris. Prot...

Use 251323

Timing Chain Tensioner Retaining Clip - secures the timing chain tensioner and its spring within the timing cover on the 2.25L four-cylinder petrol...

Woodruff Key - Camshaft Chainwheel for the 4-cylinder engine timing assembly. This Woodruff key locates the camshaft chainwheel on the camshaft no...

Core Plug - 1-3/8 in. diameter, threaded - for the Series engine block. This threaded plug seals a casting aperture in the engine block, retaining...

Gear Lever Bracket - mounting bracket for the gear change lever on the LT76 gearbox. The gear lever pivots in the bracket, locating the lever over...

Gearbox Crossmember - SWB is a weld-on steel chassis crossmember that mounts beneath the gearbox and transfer box assembly, providing structural su...

Transfer Box Gear - High is the high range gear wheel in the Land Rover Series transfer box assembly, fitting Series vehicles from 1948 to 1984. T...

External Circlip - retaining circlip fitted within the LT67 main gearbox. Seats in a shaft groove to axially locate a gear, bearing or spacer on i...

Alternator Bearing Kit - a service kit containing the bearing components required to recondition an alternator unit. Intended for use during alter...

Brake Vacuum Tank for the Land Rover Series III 2.25 Diesel. Fitted in the brake servo vacuum circuit, the tank stores a vacuum reserve to ensure c...

Sealing Washer for the coolant temperature transmitter adaptor, for use on the 2.25L Diesel, 2.5L Diesel, and 2.5L Turbo Diesel engines. Fitted at...

Fuel Filter Centre Bolt for the diesel fuel filter and sedimentor assembly. This through-bolt clamps the filter bowl and element onto the filter h...

Gearbox Reverse Stop Adjuster screw, part of the reverse gate mechanism in the manual gearbox gear-selection assembly. It sets and limits the gear...

Mainshaft Thrust Washer for the Series I and Series II gearbox assembly. This 0.135 in (135 thou) washer controls the axial location of 3rd gear o...

Seat Belt Anchorage Frame is a front seat belt mounting bar for Soft Top vehicles, providing secure anchorage points where the open body offers no ...

Sliding Window Kit - Deluxe, supplied as a pair for the rear body sides. The kit fits a horizontally sliding glass window into the rear side panel...

Sliding Window Kit - a pair of sliding side windows fitted with green-tinted toughened glass certified to E11 CE R-43. The sliding panes provide op...

Crystal Headlamp - a matched pair of 7-inch round crystal halogen headlamps for right-hand-drive applications. The clear (crystal) lens and facete...

7" Crystal Halogen Headlamp - round headlamp unit for the front lighting assembly, supplied as a matched pair. The clear crystal lens works with a...

7" Crystal Halogen Headlamp - round headlamp unit for the front lighting assembly, supplied as a matched pair. The clear crystal lens works with a...

Voltage Regulator (control box) of the screw-terminal type, for dynamo charging systems. The control box is wired between the dynamo and the batte...

Upper Tailgate Lock Cap for the rear end door handle assembly. This small plastic cap fits over the end of the upper tailgate handle, covering and...

Self-Tapping Screw for body and trim fixing applications. Used to secure window surrounds, bodyside trim, facia and switch panels. The self-tappin...

T-Piece Hose Connector is a three-way junction fitting used in a flexible hose run. It joins three hose ends at a single point, allowing a hose li...

7 Inch Round LED Headlamp for the front lighting system, replacing the conventional 7-inch round sealed-beam or halogen headlamp. The LED light so...

Manifold Stud is an M8 x 65 mm threaded stud that secures the inlet and exhaust manifold to the cylinder head on the four-cylinder petrol engine. ...

Glass

Polyurethane Bush Set in yellow, supplied for suspension mounting points that use a rubber-style bush. Supplied as a set of yellow polyurethane bu...

Girling Shock Absorber for the front suspension, a hydraulic damper for heavy-duty suspension applications. Mounted between the axle and the chass...

Seat Box Corner Protector set, supplied as a pair to guard the exposed corners of the seat box against knocks and wear. Each protector is CNC cut ...

Rotor Arm for the Lucas distributor in the ignition system of the 2.0L and 2.25L 4-cylinder petrol engines (up to engine suffix C). Driven by the ...

Oil Pressure Switch for the engine lubrication system warning circuit. This pressure-sensitive switch threads into the engine block oil gallery an...

Bulkhead Repair Panel with Vents - Left-Hand is a weld-in repair section for the upper corner of the bulkhead, incorporating the fresh-air vent sur...

Bulkhead Top Corner Repair - RH

Bulkhead Repair Panel with Vents - Right-Hand is a weld-in repair section for the upper corner of the bulkhead, incorporating the fresh-air vent su...

Bulkhead Repair Panel with Vents - Left-Hand is a weld-in repair section for the upper corner of the bulkhead, incorporating the fresh-air vent sur...

Braided Earth Strip is a flexible braided conductor that forms an electrical earth (ground) bond between two points in the vehicle. It provides a ...

Steel Ball - 9/32 inch steel ball used in the steering column assembly. Supplied individually. Ball diameter 9/32 inch (7.14 mm).

Rubber isolator clamp used in the bonnet-mounted jack bracket assembly to secure the jack beam or handle against the bonnet mounting brackets. The...

Headlamp Bowl Seal - the gasket that seals the 7-inch headlamp bowl against the surrounding body panel. Fitted around the lamp aperture, it closes...

Drive Screw for use in Land Rover body, chassis, and hardware assembly. A No.14 × 1" drive screw, supplied individually.