Land Rover Series Parts

Nut, 1/2" UNF. A threaded fastener used on the early 4-cylinder diesel engine assembly.

Fitment: All models to (VIN) KA930455 All models 1980 on

Coolant Bypass Hose for the 4-cylinder petrol and naturally-aspirated diesel engines (non-TDi). It forms the bypass path of the engine cooling cir...

Hydraulic Tappet fitted within the V8 petrol engine valve train, where it maintains zero valve clearance automatically. Engine oil pressure fills ...

Hub Nut Socket is a 52mm deep impact socket with a 1/2" square drive, used to remove and refit the hub retaining nut on the wheel bearing assembly....

Bonnet Hinge Bolt Kit - a set of stainless steel fixings for mounting the bonnet hinges that allow the bonnet to pivot open. The kit secures the h...

Fuel Tank Mount is a rubber mounting that supports the fuel tank on the chassis. It cushions the tank on its mounting bracket, isolating it from c...

Water Pump Gasket seals the coolant pump to the engine front cover on the V8 petrol engine. It fits at the pump mounting face, sealing the coolant...

Engine Plug (3/8 BSF thread) for Land Rover 4-cylinder petrol and diesel engines. This threaded blanking plug is used at multiple points across th...

Window Channel - Top is the upper glass-run channel that guides the top edge of the window glass, supplied as a 94 cm length. It forms the running...

Door Latch - Rear - Anti-Burst is the latching mechanism for the rear end door, operating within the body closure system. It mounts to the rear do...

Rear Fog Lamp for the rear lighting circuit, providing the high-intensity red rear light used to make the vehicle conspicuous from behind in poor v...

Wiper Drive Cable for the windscreen wiper system on cable (rack) type wiper drives. The flexible toothed cable runs inside the wiper rack tubing ...

Nyloc Nut - M12

Fuel Filter with a paper filter element, for carburettor petrol engines. Part of the fuel supply system. The filter is plumbed inline between the ...

Brake Union for the hydraulic braking circuit, with male 7/16"-20 UNF thread for 1/4" diameter brake pipe. This male-threaded end fitting connects...

Cylinder Head Gasket for the 2.25L and 2.5L 4-cylinder petrol engine. This gasket is fitted between the cylinder head and the engine block, sealin...

Coolant Hose for the water pump circuit on the 3.5L V8 Twin Carb petrol engine. This hose connects the water pump outlet to the coolant pipe, rout...

Rear Stop/Tail Lamp - combined rear stop and tail lamp, supplied as a complete lens and body assembly. It mounts in the rear lamp position and pro...

Water Pump Gasket - 7-Hole for the cooling system on Land Rover 4-cylinder military engines. This gasket seals the mating face between the water p...

Seat Base - Outer is the lower seat cushion for either outer (driver or passenger) position in the front seating assembly. Foam-padded and finishe...

Wind Deflector Set - a pair of stick-on air deflectors for the front door windows. Each deflector fits to the outer edge of the door window frame ...

Swivel Ball Seal Retainer for the front axle swivel housing. This retaining ring clamps the swivel housing oil seal against the swivel ball, holdi...

Wiper Spindle Kit: the front wiper wheel box assembly that houses and supports the wiper arm spindle. Fitted in the scuttle, the wheel box guides ...

Bulkhead Vent Hinge Pin Kit in stainless steel - replaces the pivot pins on which the bulkhead (scuttle) air vent flaps hinge. The original steel ...

Clutch Fork Clip secures the clutch arm rod to the release fork inside the gearbox bellhousing on LT77, LT85, and R380 5-speed manual gearboxes. T...

Glow Plug (cold-start heater plug) threaded into the cylinder head, part of the diesel cold-start heating circuit. The heated tip projects into th...

Bottom Overhaul Gasket Set for the 3.5 V8 petrol engine. The set supplies the gaskets and seals used to reseal the lower engine once the sump is r...

Pop Rivet (blind rivet) for fastening panels, trim and brackets where access is only available from one side. The rivet is fitted into a drilled h...

Wiper Arm - front windscreen wiper arm, right-hand. The 5mm is the narrow width of the arm, which sets the wiper-blade fitting - it is not a spind...

Brake Hose - flexible hydraulic line in the rear braking circuit, connecting the chassis-mounted rigid brake pipe to the rear axle brake assembly. ...

Nut - M6 is a plain M6 hexagonal nut used as a general-purpose threaded fastener throughout the chassis, body and mechanical assemblies. It tighte...

O-Ring - seal for the LT76 manual gearbox, seated within the transmission assembly to seal a mating joint against oil leakage. Early-type ring, fi...

Zenith Carburettor for the 2.25L petrol engine, part of the fuel and induction system. It meters fuel into the incoming air stream to form the air/...

Stainless Steel Bolt Kit for securing the front door hinges to the body on the 2-door Defender. The fasteners replace the original mild-steel fixin...

Drain Plug - a tapered threaded plug used to seal and drain fluid from engine and driveline housings. It serves as a coolant drain plug in the cyl...

Exhaust Clamp for the exhaust-to-chassis mounting. Two-bolt upper clamp plate that forms the exhaust-to-chassis mounting assembly on Series and ea...

Flywheel Housing O-Ring - a sealing ring at the rear of the engine where the flywheel housing meets the cylinder block. Fitted to the 2.25L engine...

Reflector SIII

Shock Absorber - rear suspension damper for the short-wheelbase chassis. Mounted between the rear axle and the chassis bracket, it controls spring...

Fuel Pump - Petrol 4-Cyl for the mechanical fuel delivery system on Land Rover 2.25L 4-cylinder petrol engines. This mechanical lift pump is drive...

Electric Fuel Pump mounted externally in the fuel supply system, drawing petrol from the tank and delivering it to the carburettor. This is an ext...

Flange Bolt, M8 x 50 mm - a hexagon-head bolt with an integral flange beneath the head. The flange spreads the clamping load over a wider bearing ...

Ignition Coil - high-tension coil in the ignition system. Converts the low-voltage supply into the high-tension voltage required to fire the spark...

Centre Cubby Box finished in black vinyl, fitting the centre position between the front seats to provide an enclosed storage compartment with a mou...

Mounting Stud is a threaded fixing used in the rear body upper fixings. It is an M8 stud, 67 mm in length, providing a fixed threaded mounting poi...

Fir Tree Fastener secures interior body and roof trim panels to the vehicle structure. The ribbed, tapered fir-tree shank pushes into a panel hole...

Reservoir kit