Land Rover Series Parts

Core Plug, 1 7/8" diameter, sealing a casting core hole such as those in the inlet manifold and engine castings. Core plugs close the openings lef...

Instrument Panel Bulb, rated 12V 2W with a BA7s bayonet base (type 281), for the instrument cluster lighting circuit. It provides the internal ill...

Relay - 12V automotive changeover relay with a 30A contact rating, twin make. The five-pin configuration provides two normally-open contacts, allo...

Side Cover Gasket sealing the cylinder-block side cover (tappet inspection cover) to the block face on diesel engines. The side cover closes the p...

Swivel Housing Washer for the swivel pin housing drain plug, part of the front axle swivel assembly. The sealing washer fits beneath the drain plu...

Seat Box Corner Protector - Pair - Black Steel

Handbrake Return Spring is part of the transmission-mounted drum-type handbrake, acting on the relay lever within the parking brake mechanism. Whe...

Track Rod End Boot for the steering track rod end ball joint. This rubber boot fits over the track rod end housing, sealing the ball joint against...

Bolt for the suspension mounting. A 7/16" UNF thread bolt of 6.5" length, used at the upper suspension mounting to secure the shock absorber and sp...

Rear Shock Absorber - rear suspension damper for the long-wheelbase chassis. Mounted between the rear axle and the chassis bracket, it controls sp...

Flasher Unit for the direction-indicator circuit, of the 2-pin type without trailer-socket provision. The flasher unit switches the current to the...

Clutch Release Fork Kit for the manual transmission clutch release mechanism, built around a cast release fork. The fork pivots on its mounting in...

Clutch Cover (pressure plate assembly) for the clutch on 4-cylinder petrol applications. The cover bolts to the flywheel and houses the diaphragm ...

Swivel Pin Shim for the front axle swivel housing assembly. This 0.030" shim is fitted beneath the upper swivel pin retaining plate and is used to ...

Clutch Slave Cylinder, part of the hydraulic clutch release circuit. The slave cylinder receives fluid pressure from the clutch master cylinder an...

Distributor Rotor Arm for the 3.5L V8 petrol ignition system. The rotor arm sits on top of the distributor shaft beneath the cap and rotates to dis...

Crankshaft Timing Chain Sprocket The drive sprocket mounted on the nose of the crankshaft within the timing chain drive of the Rover V8 petrol engi...

Bolt 5/16" UNF x 2" is a hex-head set bolt with a 5/16-inch Unified National Fine (UNF) thread at 24 threads per inch and a 2-inch shank length. I...

Fixing Screw for the front door hinge and check strap assembly. This screw secures the door hinge and the check strap (door-stay) to the body pill...

Differential Drive Flange for the Salisbury rear differential. It bolts to the differential pinion shaft and forms the coupling face to which the r...

Water Temperature Sender threads into the cooling system and measures engine coolant temperature, feeding the signal to the dashboard temperature g...

Bottom End Gasket Set for the overhaul of the 2.25L diesel engine (3- and 5-main-bearing), covering the gasket and joint requirements of the lower ...

Bolt with a 3/8" UNF (Unified National Fine) thread and a 1-7/32" length. A standard imperial-thread fastener for chassis, driveline and body fixi...

Tailgate Chain Cover - a pair of protective sleeves that fit over the two retaining chains supporting the rear tailgate. Each chain links the tail...

Bolt, a hexagon-head fastener with a 5/16" UNF thread, 7/8" long. This imperial fastener is of the UNF (Unified National Fine) thread series and i...

Hazard Flasher Relay - the switching relay in the hazard warning circuit. When the hazard switch is operated, the flasher relay pulses all four di...

Lower Swivel Pin O-Ring for the front axle swivel housing assembly. It seals the joint at the lower swivel pin, where the steering arm and lower pi...

4WD High Gear Selector Spring for the transfer box four-wheel-drive selector mechanism. The spring acts on the high-range four-wheel-drive selecto...

Front Halfshaft Bearing - roller bearing supporting the inner end of the front halfshaft within the front axle housing. Located at the inboard end...

Stop/Tail Lamp Assembly for the rear lighting circuit, combining the tail (running) light and stop (brake) light in a single unit. The assembly mo...

Con Rod Bearing Set for the 2.25L four-cylinder petrol engine. The set provides the big-end shell bearings that carry the connecting rods on the c...

Oil Pressure Switch threads into the engine block oil gallery and monitors lubrication system pressure. It operates the low oil pressure warning l...

Bolt – 3/8" BSF x 1-1/4" is a threaded fastener used in the front axle assembly, securing the swivel pin housing. The bolt has a 3/8 inch diameter...

Swivel Pin Shim, 0.010" thick, fitted at the front axle swivel pin housing. The shim is placed beneath the swivel pin (king pin) to set the correc...

Swivel Pin Shim, 0.005" thick, fitted at the front axle swivel pin housing. The shim is placed beneath the swivel pin (king pin) to set the correc...

Door Hinge - left-hand door hinge that mounts the side door to the body hinge pillar and carries the door as it swings. Steel hinge for the front ...

Self-Tapping Screw – No. 8 × 1/2 in is a general-purpose fastener used across body, trim and electrical fixings, such as lamp guards, wheelguards, ...

Spring Washer - M6 single-coil spring lock washer. Fitted beneath a nut or bolt head, the split single-coil section bears against the fastener to ...

Steering Box is the recirculating-ball power steering gear at the heart of the steering system, converting rotation of the steering column into the...

Hex-head bolt, 5/16" UNF thread, 1" long. Unified Fine (UNF) thread form with a hexagonal head for use with standard imperial spanners and sockets...

Water Pump for the 2.25L 4-cylinder engine, operating in the engine cooling circuit. Belt-driven from the crankshaft pulley, the pump circulates c...

Hex Nut, 7/16" UNF, plain steel. This full hex nut secures the door top to the door base on Series models and is used at other 7/16" UNF fixing po...

Lock Striker Plate is the body-mounted plate the door latch engages to hold the door closed. Fixed to the door aperture face, it provides the stri...

Brake Pipe Union - a female union fitting for 3/16" (4.75mm) hydraulic brake pipe, with an M10 x 1mm thread. Machined from brass, it threads onto ...

Handbrake Pull-Off Spring for the transmission-mounted drum handbrake assembly. This return spring retracts the brake shoes against the backplate ...

Head Gasket Seals the cylinder head to the cylinder block on the pre-TDi 2.25L and 2.5L naturally aspirated and turbocharged diesel engines. It co...

Core Plug (Cup Type) for sealing the core holes left in the engine block casting after the sand cores are removed during manufacture. The cup-shap...

Headlamp Assembly for the front exterior lighting system, supplied as a pair. Each crystal-style halogen unit mounts in the front lighting housing...