Land Rover Series Parts

Outer Hub Lock Washer for the front and rear hub assembly on Land Rover solid axles. This lock washer secures the hub bearing retaining nut agains...

Transfer Gear Lever Gaiter for the high/low ratio selector lever on the Series Land Rover transfer box. This rubber gaiter seals around the transf...

Drive Member Joint Washer - a sealing gasket fitted between the drive flange and the outer hub on Land Rover Series solid axles. This gasket seals...

Gearbox Gasket Kit - No Seals for the 4-speed manual gearbox and transfer box on Series models. This set supplies the paper and fibre mating gaske...

Brake Drum Screw for the brake drum assembly. This retainer screw secures the brake drum to the wheel hub flange, preventing the drum from displac...

Propshaft Gaiter with Clips for the front propshaft sliding joint. This rubber gaiter fits over the splined sliding joint (slip yoke) of the front...

Crankshaft Spigot Bush is the clutch pilot bush that presses into the rear face of the crankshaft, between the engine and the clutch. It supports ...

Drive Shaft Hub Cap for the hub assembly on Land Rover Series vehicles. This cap fits at the outer face of the hub, closing off the drive shaft en...

Gear Lever Gaiter for the transmission tunnel. This flexible boot fits around the base of the gear lever where it passes through the tunnel, sealin...

Hub Nut Spanner for the front hub and wheel bearing assembly. The 52mm tool engages the hub retaining nut on the front stub axle. Designed for use...

Drain Plug Washer in copper, used to seal axle differential drain plugs against oil leakage. This copper crush washer seats under the drain plug a...

Wheel Cylinder Bleed Screw fits into the bleed nipple port of the wheel cylinder in the drum brake assembly, allowing the hydraulic circuit to be p...

Brake & Clutch Pedal Pad for the foot pedal assembly. This moulded rubber pad fits over the brake and clutch pedal arm, providing the grip surf...

Swivel Housing to Stub Axle Joint Washer for the front axle swivel assembly. This sealing washer fits between the swivel housing and the stub axle...

Interior Mirror for Series Land Rover models. Direct-fit interior rear-view mirror providing rearward visibility from the driver's position inside...

Wiper Blade for the front windscreen, with a stainless steel frame. The blade clears the driver's field of view across the front windscreen. It at...

Wheel Cylinder for the drum brake assembly - the left-hand hydraulic slave cylinder that operates the brake shoes. The same cylinder serves either ...

Oil Pressure Switch for the engine lubrication system warning circuit. This pressure-sensitive switch threads into the engine block oil gallery an...

Axle Breather for the front axle housing on vehicles without a remote breather pipe assembly. This screw-in vent allows the air inside the front a...

Brake Hose - the flexible hydraulic line in the braking system. It carries pressurised brake fluid from the rigid chassis- or axle-mounted brake pi...

Oil Seal for the swivel pin housing on the front axle, sealing against the polished surface of the swivel ball. The seal seats in the rear face of...

Differential Pinion Oil Seal for the axle differential housing. This oil seal fits around the pinion flange where the propshaft coupling connects,...

Swivel Pin Housing Gasket for the front axle swivel assembly. This gasket seals the mating face between the chrome swivel ball housing and the fro...

Driving Member Bolt for the axle driving member assembly. This 3/8" BSF x 1-19/32" bolt retains the driving member to the hub assembly. The drivin...

Joint washer

Front left-hand wheel cylinder for the hydraulic front braking system, installed within the brake backplate assembly of 11-inch front brake configu...

Shock absorber bush (eye), anti roll bar bush

Spring Bush for the leaf spring suspension system on Series Land Rovers. This rubber bush fits into the spring eye at the front fixed mount and re...

Transfer Box Sump Gasket for the LT76 combined gearbox and transfer box unit used in Series Land Rovers. This flat sealing washer seals the transf...

Fuel Sender Unit Gasket for the fuel gauge sender unit fitted to the fuel tank. This gasket seals the joint between the sender unit flange and the...

Upgrade your Series Land Rover suspension with this Polyurethane Shock Absorber Bush Set in black. The set includes 4 pieces, providing everything ...

Exhaust Gasket sealing the exhaust manifold-to-downpipe flange on Series Land Rover 4-cylinder petrol and diesel engines. This four-hole flange ga...

Wheel Cylinder for the drum brake assembly - the right-hand hydraulic slave cylinder that operates the brake shoes. The same cylinder serves either...

U-Bolt Nut - 7/16 BSF for use in the leaf spring suspension assembly. U-bolts clamp the leaf spring pack to the axle casing at the front and rear ...

Rubber Sealing Ring for gear selector shafts in the LT76 gearbox and LT95 transfer box. In the LT76 gearbox, two rings are fitted per unit, sealin...

Axle Key Washer for the hub nut locking system in the axle assembly. This tab washer seats beneath the axle hub nut, with tabs that locate into ma...

Rear brake drum installed in the rear drum brake assembly of the vehicle braking system. The drum mounts to the rear hub and rotates with the wheel...

Front Brake Shoe Spring for the front drum brake assembly. This return spring connects the two brake shoes and pulls them back off the drum when th...

Axle Bump Stop - rubber bump stop for the front and rear suspension axle assemblies. Fitted to the chassis above each axle, the bump stop limits a...

Wheel Cylinder Overhaul Kit for front drum brake systems fitted with 11-inch brake drums. This kit provides the necessary parts to overhaul all fo...

Oil seal

Lock Plate for the front axle assembly. This metal tab washer locks fastener heads in position by bending a tab against the bolt head or nut after...

Side Cover Gasket sealing the cylinder-block side cover (tappet inspection cover) to the block face, for petrol and diesel engines. The side cover...

Detent Spring for the manual gearbox gear selector mechanism. The spring loads the detent ball against the selector shaft, holding the selected ge...

Output Shaft Oil Seal seals the front or rear output shaft of the LT76 transfer gearbox, retaining lubricant within the transfer case and preventin...

Accelerator Spring for the throttle linkage on diesel engines. This return spring acts on the accelerator linkage, drawing the throttle back to th...

Gear Lever Knob threads onto the top of the main gearbox gear lever to form the hand grip used for gear selection. It gives the driver a defined c...

Oil Filter for the engine lubrication system, suited to the 2.0L and 2.6L IOE (inlet-over-exhaust) petrol engines. The filter traps metallic parti...