for Discounts / VAT
for Discounts & Correct VAT
Parts for the full Land Rover Series family, produced from 1948 to 1985. This collection covers Series I, Series II, Series IIA, and Series III in both short wheelbase and long wheelbase configurations. Select your generation below to find correctly fitted components for your vehicle.
Window Seal: rubber glazing seal for the window glass, sealing it against water and draughts.
Front Outer Seat Cushion Base for the adjustable seat frame in Series II, IIA, and III 109" long-wheelbase vehicles. This is the outer seat base c...
View full detailsShackle plate
Valve Collet for the valve gear of the 2.25L petrol and 2.0L diesel engines, used with single-groove valve stems. The split collets seat in the gr...
View full detailsJoint Washer for the LT76 manual gearbox. Fitted between mating faces within the gearbox to form an oil-tight joint on assembly. Supplied as a sin...
View full detailsThrust Washer - 0.128" A gearbox mainshaft thrust washer for the second-speed gear, 0.128" thick. It controls the end-float of the 2nd-speed gear ...
View full detailsCamshaft for the 2.25L 4-cylinder petrol engine valve train. Running in the cylinder block and driven from the crankshaft by the timing gear, the ...
View full detailsRear Shackle Plate, part of the rear leaf spring mounting in the suspension assembly. The shackle plate forms one side of the spring shackle, link...
View full detailsBrake Servo Repair Kit for the Type 50 vacuum brake servo unit (227mm diameter). This overhaul kit contains the components necessary to rebuild th...
View full detailsBulb rated at 24V 5W, for use in side lamp and parking light circuits on 24V vehicle electrical systems. Small-wattage bulb designed for marker an...
View full detailsBarrel Lock and Key, Set of Two for the door locks, supplied as two keyed lock barrels each with a key. Each barrel is the cylinder the key turns ...
View full detailsSeat Back and Headrest for the outer front seat, in the deluxe pattern and finished in black. This is the upholstered backrest (squab) the occupant...
View full detailsParabolic Spring Kit for the rear leaf-sprung suspension. Parabolic springs replace the standard multi-leaf semi-elliptic springs with a smaller nu...
View full detailsDrop Plate Strengthener for the towing equipment assembly. It acts as a spacer and strengthener for the towing jaw and the towing jaw/ball fixings...
View full detailsShock Absorber for the rear axle, damping suspension movement by converting the energy of spring oscillation into heat as the axle moves relative t...
View full detailsBall Joint - Accelerator Linkage is a mechanical pivot joint used in the accelerator linkage assembly. This ball joint connects articulating rods ...
View full detailsGearbox Selector Shaft Pin - an interlock pin within the gearbox selector mechanism. It sits between the selector shafts (rails) and prevents more...
View full detailsRear Shackle Pin for the rear leaf spring shackle. The pin secures the spring shackle at the rear mounting of the rear leaf spring, allowing the s...
View full detailsStarter Pinion Retaining Kit for the inertia (Bendix) drive of the starter motor fitted to 4-cylinder and 6-cylinder petrol engines. The starter p...
View full detailsFuel Tank Outrigger is a rear chassis outrigger forming part of the body & chassis assembly. It welds to the main chassis rail to support the ...
View full detailsWinch Remote Control operates an electric recovery winch wirelessly, allowing the operator to stand clear of the winch line during recovery. Wirel...
View full detailsManifold Absolute Pressure (MAP) Sensor, part of the engine management system. The MAP sensor measures the absolute pressure inside the intake man...
View full detailsRear Door Trim Panel - a black interior trim panel that finishes the inner face of the rear side-hinged door, covering the door frame to give a cle...
View full detailsGlow Plug Lead in the diesel glow plug (heater plug) pre-heat circuit. This short 5" lead interconnects glow plugs wired in series and is not inte...
View full detailsSteering Box - LHD is the manual steering gearbox at the heart of the steering system. It converts rotation of the steering wheel and column into ...
View full detailsMetal Fuel Filler Cap seals the fuel tank filler neck, closing the fuel system against contamination, spillage and evaporative loss. The cap secur...
View full detailsReverse Selector Fork for the gear selection mechanism in the Series-type manual gearbox (LT76), suffix B onwards. Mounted on the selector shaft, ...
View full detailsRoof Access Ladder in a hot-dip galvanised steel finish, providing safe access to a roof rack. This is a non-drill (bolt-on) type ladder that moun...
View full detailsSpherical Bearing Bush - Clutch Cross Shaft for Series 1, Series 2, and Series 3 Land Rover vehicles. The clutch cross shaft is supported at its p...
View full detailsFront Chassis Leg for the left-hand (nearside) front of the chassis. A welded chassis repair section that renews the front chassis leg where the o...
View full detailsFolding Side Step - Series
Layshaft First Gear - the first-speed gear on the layshaft (countershaft) of the main gearbox. Meshes with the corresponding mainshaft gear to pro...
View full detailsTailgate Hook for the lower hinged tailboard, left-hand side. This pigtail (spiral) hook mounts on the body and retains the tailboard chain, holdi...
View full detailsSynchro Hub for the 3rd/4th gear synchroniser assembly in the Series-type manual gearbox (LT76). The hub carries the synchroniser mechanism that m...
View full detailsDipstick Tube - the guide tube through which the engine oil level dipstick passes down into the sump. It locates in the cylinder block and directs...
View full detailsExhaust Pipe - Intermediate - Non-Station Wagon
Water Pump - 2.0 IOE - the engine coolant pump in the cooling system, for the 2.0L IOE (inlet-over-exhaust) petrol engine. Driven by the fan belt ...
View full detailsFan Belt for the engine front-end auxiliary drive. Driven from the crankshaft pulley, this belt turns the water pump and cooling fan together with...
View full detailsParabolic Spring and Shock Kit is a complete rear leaf-spring suspension package, replacing the original multi-leaf springs and dampers at the rear...
View full detailsBrake Pipe Set - a complete set of pre-formed rigid brake pipes for the hydraulic braking circuit, shaped for left-hand-drive (LHD) routing. Repla...
View full detailsFootwell Repair Panel - Ribbed - RH - LHD
LH Footwell Repair Panel - Series 2/3 LHD
Front Spring Shackle Plate Kit for the heavy-duty 1-ton leaf spring suspension. The shackle plates link the leaf spring eye to the chassis hanger,...
View full detailsChubby Cubby Box - a between-seats storage box and armrest that mounts on the centre panel of the seat box. It provides lockable interior storage ...
View full detailsSpare Wheel Carrier Hinge Bush - a pair of nylon bushes for the swing-away spare wheel carrier (DA2232 / GA2232). The bushes line the hinge pivot ...
View full detailsLower Door Trim Panel for the left-hand door. This panel covers the lower section of the inner door structure, forming the interior trim surface b...
View full detailsLower Door Trim Panel for the right-hand door. This panel covers the lower section of the inner door structure, forming the interior trim surface ...
View full detailsLock Nut for the Land Rover Series gearbox primary pinion bearing. This nut retains the front bearing on the primary pinion (input shaft), securin...
View full detailsParts for the full Land Rover Series family, produced from 1948 to 1985. This collection covers Series I, Series II, Series IIA, and Series III in both short wheelbase and long wheelbase configurations. Select your generation below to find correctly fitted components for your vehicle.
80, 86, 88 and 107-inch wheelbase variants. 1.6-litre and 2.0-litre petrol, 2.0-litre diesel from 1957.
Land Rover Series I parts (1948 to 1958) →88-inch SWB and 109-inch LWB. 2.25-litre petrol and diesel, 2.6-litre straight-six and 3.5-litre V8 in select variants.
Land Rover Series II, IIA and III parts (1958 to 1985) →The Land Rover Series family spans four distinct generations produced across 37 years. Series I ran from 1948 to 1958, Series II from 1958 to 1961, Series IIA from 1961 to 1971, and Series III from 1971 to 1985. Each generation used a body-on-frame ladder chassis with selectable four-wheel drive, a two-speed transfer gearbox, and a four-speed manual main gearbox. Wheelbase options were 88 inches (short wheelbase) and 109 inches (long wheelbase) from Series II onward. Series I used wheelbase options of 80, 86, 88, and 107 inches across its production run.
Parts compatibility is not uniform across the family. Some components, particularly engine internals for the 2.25-litre petrol and diesel units, carry across from Series IIA through Series III. Others, including body panels, wiring looms, and axle components, are generation or wheelbase specific. Selecting the correct child collection for your vehicle is the most reliable way to find the right parts.
Browse by generation:
If you are unsure which generation you have, use the vehicle commission number to identify your build date and sub-series before selecting parts.
The Land Rover Heritage Trust holds production records and commission number data for the Series family and is a reliable resource for vehicle identification.
This collection covers components across all major categories for the Series family. The heaviest demand comes from engine and gasket components, suspension and steering parts, body and chassis hardware, electrical and wiring items, and service and maintenance consumables.
Common restoration categories include engine rebuild components (gaskets, seals, bearings, timing parts), swivel housing and axle parts, wiring looms and electrical connectors, body panels and bulkhead sections, brake system components, and clutch and drivetrain parts.
For cross-category browsing by component type, the following category collections carry Series-compatible stock alongside parts for other Land Rover models:
Use the Model filter available on category collection pages to narrow results to Series I or Series 2 and 3 fitment where supported.
Buying GuideThe product grid offers three quality tiers: Genuine, OEM, and Aftermarket.
Genuine parts carry the original Land Rover part number and were manufactured by or for Land Rover. For Series vehicles, genuine Land Rover stock is limited for many components due to the age of the range. Where genuine parts are available, they are listed as Genuine.
OEM parts are manufactured to the same specification as the original part, often by the same supplier that produced the original component, but are sold outside the main brand distribution channel. For Series vehicles, OEM-specification parts are a reliable and widely used choice for mechanical rebuilds.
Aftermarket parts are independently manufactured to a compatible specification. Quality varies by product, and each listing on this site identifies the quality tier clearly. For consumable and body hardware categories on Series vehicles, quality aftermarket parts are the standard choice used by workshops across Europe.
Trade BuyersTrade customers running a workshop or managing multiple Series vehicles can access volume pricing through a Budget Parts trade account. Trade accounts include correct EU VAT invoicing, consolidated order options, and direct contact with the sourcing team for unlisted parts.
If a component is not currently visible in the catalogue, the sourcing team works directly with UK and EU suppliers to locate it. Contact the team with your commission number and part requirement.
Vehicle IdentificationSeries Land Rovers do not carry a modern 17-digit VIN. Each vehicle has a Commission Number on a bulkhead plate that encodes the generation, engine type, wheelbase and build date. Since the identification process and the records you cross-reference against differ between the four generations, the detailed Commission Number guidance lives on the two child collections, scoped to the vehicles each one covers.
For Series I (1948 to 1958), see the Series 1 collection. For Series II, IIA and III (1958 to 1985), see the Series 2 and 3 collection. Both pages cover where the plate sits on each generation, what the encoding tells you, and what to do if the plate is missing. If you have your Commission Number to hand and want fitment confirmed before ordering, contact Budget Parts directly.
Background ReadingFor deeper engineering and restoration context beyond the scope of this hub page, the following long-form guides cover each generation in detail. They are reference reading rather than navigation; the two child collections above are the route to parts.
A detailed reference covering Series I engine variants (1.6-litre and 2.0-litre petrol, 2.0-litre diesel), chassis design, wheelbase evolution, and the critical parts considerations for accurate restoration. Relevant for anyone sourcing components for a Series I vehicle or confirming specifications before ordering.
Series I engine and restoration guide →Covers the engineering and production history of Series II, IIA, and III models, including key differences between generations, engine fitment across sub-variants, and why certain parts are interchangeable while others are not. Useful background before selecting parts from the Series 2 and 3 collection.
Series II, IIA and III restoration guide →These are four successive generations of the same utility vehicle family, each sharing the core body-on-frame architecture but differing in engine, bodywork, and specification. Series I ran from 1948 to 1958 and used a 1.6-litre then 2.0-litre petrol engine, with a diesel option from 1957. Series II ran from 1958 to 1961 and introduced a revised body style. Series IIA ran from 1961 to 1971 and is the highest-volume production variant, available with 2.25-litre petrol and diesel engines and, in certain long wheelbase models, a 2.6-litre straight-six. Series III ran from 1971 to 1985 and brought minor updates including a revised instrument panel and an optional 3.5-litre V8 in select variants. Understanding which generation you have is the essential first step in selecting the correct parts.
Some parts are shared across Series IIA and Series III, particularly engine internals for the 2.25-litre petrol and diesel units, and certain axle and drivetrain components. However, body panels, wiring configurations, and some suspension components differ between generations. Parts shared across Series II and Series IIA are sometimes also different from early and late Series III specifications. The safest approach is to confirm fitment by generation and wheelbase before ordering, and to use the Series 2 and 3 parts collection for those specific generations.
Yes, significantly. Series I vehicles used different wheelbase dimensions (80, 86, 88, and 107 inches depending on year), different body construction details, and earlier engine specifications including the 1.6-litre petrol and the pre-2.25-litre 2.0-litre units. Many body, chassis, and mechanical components are unique to the Series I and do not carry across to Series II or later. The Series 1 parts collection is dedicated to this generation.
Start by identifying which generation your vehicle is. Series I (1948 to 1958) parts are unique to that generation in body, chassis and engine, and live in the Series 1 collection. Series II (1958 to 1961), Series IIA (1961 to 1971) and Series III (1971 to 1985) share considerable parts overlap and are grouped together in the Series 2 and 3 collection. If you are not sure which generation you have, the Commission Number on the bulkhead plate will tell you, and the child collections cover identification in more detail. Use the generation grid above to navigate to the correct collection for your vehicle.
Yes. The Series Land Rover aftermarket is one of the most active classic vehicle parts ecosystems in Europe. New replacement parts are produced for all four generations across the major categories: engine internals for the 2.25-litre petrol and diesel and the 2.0-litre Series I engines, body panels and chassis sections, electrical and wiring components, brake and suspension parts, and full restoration hardware. Genuine Land Rover stock is limited for parts of this age, but OEM-specification parts and quality aftermarket equivalents cover the majority of components in active demand. Specialist UK and EU manufacturers continue to remanufacture Series-specific items, and Budget Parts sources from this network for items not held in catalogue stock.
Start with three steps. First, identify your generation precisely (Series I, II, IIA or III) and your wheelbase, because every parts decision flows from those two facts. Second, work through a baseline service of consumables and wear items: brakes, fluids, filters, ignition components on petrol engines, glow plugs and fuel filters on diesels. Third, plan ahead for the higher-cost restoration items that often surface on Series vehicles after a few months of use, such as bulkhead repair sections, chassis outriggers, swivel housings and gearbox components. The two child collections (Series 1, and Series 2 and 3) hold the parts. The Series I and Series II/IIA/III restoration guides linked below cover the engineering background, common faults and parts priorities for each generation in more depth.