for Discounts / VAT
for Discounts & Correct VAT
Parts for the full Land Rover Series family, produced from 1948 to 1985. This collection covers Series I, Series II, Series IIA, and Series III in both short wheelbase and long wheelbase configurations. Select your generation below to find correctly fitted components for your vehicle.
Piston for the 2.25L petrol engine, running in the cylinder bore as part of the piston and connecting-rod assembly. Supplied at +0.020" oversize, ...
View full detailsSpeedometer Cable for Land Rover models fitted with the 2.6-litre 6-cylinder petrol engine. Transmits rotational drive from the gearbox output shaf...
View full detailsPrimary Pinion for the LT76 manual gearbox, suffix D onwards. The primary pinion is the gearbox input gear, taking drive from the clutch and passin...
View full detailsSpeedometer instrument head for the dashboard instrument panel, incorporating a resettable trip odometer alongside the main total odometer. The sp...
View full detailsNyloc Nut M5 - M5 hex nyloc (nylon insert) locknut. The nylon insert creates friction against the thread to resist loosening under vibration. Stan...
View full detailsFuel Tank Elbow Pipe installed inside the petrol fuel tank as the fuel pick-up point. This elbow-shaped pipe draws fuel from the base of the tank ...
View full detailsExhaust Downpipe for the left-hand front section of the V8 petrol exhaust system. This pipe connects the left-hand exhaust manifold outlet to the ...
View full detailsDiesel Stop Control Cable operates the engine stop on the diesel injection pump. Pulling the dashboard control draws the cable to move the fuel sh...
View full detailsExhaust Tailpipe forming the final section of the exhaust system on the 109" Stage One V8. This pipe routes exhaust gases rearward from the silenc...
View full detailsExhaust Downpipe is the front downpipe of the exhaust system for the left-hand (LH) cylinder bank of the V8 engine. The downpipe bolts to the LH e...
View full detailsThrottle Lever A lever in the accelerator (throttle) linkage of the carburettor V8. It transmits movement from the accelerator cable to the carbur...
View full detailsSpring for Land Rover body and chassis application.
Seat Back - Inner - Standard - Black for the centre position of the three-abreast front bench seat in Land Rover Series vehicles. This vinyl seat ...
View full detailsDoor Top Glass - fixed piece for the Series half-door glazing assembly. This fixed glass panel fits into the top section of the Series half-door f...
View full detailsRear Body End Panel forming the left-hand rear corner of the Series body structure. This pressed steel panel is a structural outer body component ...
View full detailsBonnet Lock Striker for the hand-operated bonnet latch assembly. This striker pin is the fixed catch component in the bonnet locking system, engag...
View full detailsMud Shield - Under Wing - RH for right-hand drive Series 2 and Series 3 Land Rovers (1968-1984). Fitted beneath the inner front wing on the right-...
View full detailsRear Light Guard - Single - Natural is a steel mesh protective guard for a single rear lamp. It bolts over the rear lamp lens to shield it from im...
View full detailsFront Fuel Tank Outrigger is a chassis outrigger welded to the main frame rail, located at the rear of the front fuel tank to support and locate th...
View full detailsBulkhead Door Pillar for the right-hand (offside) front door aperture, in the basic configuration. The door pillar forms part of the bulkhead asse...
View full detailsTowing Jaw rated to 3.5 tonnes, part of the towing/pintle hitch assembly. It provides the jaw coupling for trailer and recovery towing, mounting t...
View full detailsFront Axle Drive Shaft Spacer for the front hub and stub axle assembly. The spacer fits over the front drive shaft and sets the axial position of ...
View full detailsSynchro Hub is part of the synchromesh assembly in the LT76 gearbox, splined to the mainshaft and carrying the sliding sleeve that engages the gear...
View full detailsFirst Speed Gear for the Series Land Rover main gearbox. This gear is the first-speed (lowest ratio) gear within the gearbox gear train. It is spe...
View full detailsReverse Shaft for the reverse gear train in the Series-type manual gearbox (LT76), suffix B onwards. The shaft carries the reverse idler gear, whi...
View full detailsLayshaft Gear is the gear cluster carried on the layshaft (countershaft) of the manual gearbox. Its gears run in constant mesh with the mainshaft ...
View full detailsRear Axle Half Shaft - right-hand, 10/24 spline, for the Series III rear axle. This shaft transmits drive from the rear differential to the rear wh...
View full detailsExhaust Valve for the 2.25L 4-Cylinder Petrol engine, fitted in the cylinder head valvetrain assembly. This valve operates in the cylinder head to...
View full detailsValve Cotter in the cylinder head valvetrain, locking the valve spring retainer to the valve stem. The cotters seat as a pair into the machined gr...
View full detailsInlet Valve for the cylinder head valve train, with a 34.5 mm head diameter. The inlet valve opens on the induction stroke to admit the air/fuel c...
View full detailsConnecting Rod - 2.25L Diesel
Oil Pump Driveshaft
Crankshaft with Bearings for the 2.25L 4-cylinder petrol engine. The crankshaft converts the reciprocating motion of the pistons into rotational o...
View full detailsAir Filter - air filter for the 3.5 V8 carburettor engine, fitted at the carburettor intake to filter incoming air before it is drawn through the c...
View full detailsRadiator Muff - Black is a fabric cover that fits over the radiator grille to control airflow through the radiator. Restricting cold air across th...
View full detailsTailboard Hinge Bracket Kit provides the bolt-on hinge assembly for a drop-down rear tailboard, mounting the tailboard to the rear body so that it ...
View full detailsUpgrade your Land Rover Series 2A & Series 3 SWB (1980-1984, Metric) with this +40mm stainless steel brake hose kit. +40mm Extended Length -...
View full detailsTowing Bracket Slider is the sliding tongue section of a Dixon Bate adjustable towing bracket, which sets and locks the hitch at the required heigh...
View full detailsRear Spring Hanger is a welded chassis repair section for the rear leaf-spring suspension, carrying the front mounting eye of the rear leaf spring....
View full detailsRear Bumperettes - a pair of tubular bumperettes that bolt to the rear crossmember to protect the rear corners of the body and the rear lamps from ...
View full detailsLoad Bay Liner Kit lines the rear load area to protect the original bed and inner surfaces from cargo abrasion, impact and moisture. The liner is f...
View full detailsDoor Skin - the outer skin panel for the left-hand front door, forming the outer face of the door over the door frame. It is fitted as a repair pa...
View full detailsWiper Motor Bracket Mounting bracket that locates and supports the windscreen wiper motor. Forms part of the wiper drive assembly, holding the mot...
View full detailsDirection Indicator Lamp is a rear amber turn-signal lamp to NAS (North American Specification) pattern in the 95mm round format. It is supplied a...
View full detailsPlate grommet GENUINE LR
Solonoid
Needle Valve The float-chamber needle valve for the Stromberg CD175 carburettor, part of the fuel metering assembly. It seats against the float-op...
View full detailsFront Exhaust Pipe - downpipe section of the exhaust system. Connects the exhaust manifold to the intermediate pipe and silencer, carrying exhaust...
View full detailsParts for the full Land Rover Series family, produced from 1948 to 1985. This collection covers Series I, Series II, Series IIA, and Series III in both short wheelbase and long wheelbase configurations. Select your generation below to find correctly fitted components for your vehicle.
80, 86, 88 and 107-inch wheelbase variants. 1.6-litre and 2.0-litre petrol, 2.0-litre diesel from 1957.
Land Rover Series I parts (1948 to 1958) →88-inch SWB and 109-inch LWB. 2.25-litre petrol and diesel, 2.6-litre straight-six and 3.5-litre V8 in select variants.
Land Rover Series II, IIA and III parts (1958 to 1985) →The Land Rover Series family spans four distinct generations produced across 37 years. Series I ran from 1948 to 1958, Series II from 1958 to 1961, Series IIA from 1961 to 1971, and Series III from 1971 to 1985. Each generation used a body-on-frame ladder chassis with selectable four-wheel drive, a two-speed transfer gearbox, and a four-speed manual main gearbox. Wheelbase options were 88 inches (short wheelbase) and 109 inches (long wheelbase) from Series II onward. Series I used wheelbase options of 80, 86, 88, and 107 inches across its production run.
Parts compatibility is not uniform across the family. Some components, particularly engine internals for the 2.25-litre petrol and diesel units, carry across from Series IIA through Series III. Others, including body panels, wiring looms, and axle components, are generation or wheelbase specific. Selecting the correct child collection for your vehicle is the most reliable way to find the right parts.
Browse by generation:
If you are unsure which generation you have, use the vehicle commission number to identify your build date and sub-series before selecting parts.
The Land Rover Heritage Trust holds production records and commission number data for the Series family and is a reliable resource for vehicle identification.
This collection covers components across all major categories for the Series family. The heaviest demand comes from engine and gasket components, suspension and steering parts, body and chassis hardware, electrical and wiring items, and service and maintenance consumables.
Common restoration categories include engine rebuild components (gaskets, seals, bearings, timing parts), swivel housing and axle parts, wiring looms and electrical connectors, body panels and bulkhead sections, brake system components, and clutch and drivetrain parts.
For cross-category browsing by component type, the following category collections carry Series-compatible stock alongside parts for other Land Rover models:
Use the Model filter available on category collection pages to narrow results to Series I or Series 2 and 3 fitment where supported.
Buying GuideThe product grid offers three quality tiers: Genuine, OEM, and Aftermarket.
Genuine parts carry the original Land Rover part number and were manufactured by or for Land Rover. For Series vehicles, genuine Land Rover stock is limited for many components due to the age of the range. Where genuine parts are available, they are listed as Genuine.
OEM parts are manufactured to the same specification as the original part, often by the same supplier that produced the original component, but are sold outside the main brand distribution channel. For Series vehicles, OEM-specification parts are a reliable and widely used choice for mechanical rebuilds.
Aftermarket parts are independently manufactured to a compatible specification. Quality varies by product, and each listing on this site identifies the quality tier clearly. For consumable and body hardware categories on Series vehicles, quality aftermarket parts are the standard choice used by workshops across Europe.
Trade BuyersTrade customers running a workshop or managing multiple Series vehicles can access volume pricing through a Budget Parts trade account. Trade accounts include correct EU VAT invoicing, consolidated order options, and direct contact with the sourcing team for unlisted parts.
If a component is not currently visible in the catalogue, the sourcing team works directly with UK and EU suppliers to locate it. Contact the team with your commission number and part requirement.
Vehicle IdentificationSeries Land Rovers do not carry a modern 17-digit VIN. Each vehicle has a Commission Number on a bulkhead plate that encodes the generation, engine type, wheelbase and build date. Since the identification process and the records you cross-reference against differ between the four generations, the detailed Commission Number guidance lives on the two child collections, scoped to the vehicles each one covers.
For Series I (1948 to 1958), see the Series 1 collection. For Series II, IIA and III (1958 to 1985), see the Series 2 and 3 collection. Both pages cover where the plate sits on each generation, what the encoding tells you, and what to do if the plate is missing. If you have your Commission Number to hand and want fitment confirmed before ordering, contact Budget Parts directly.
Background ReadingFor deeper engineering and restoration context beyond the scope of this hub page, the following long-form guides cover each generation in detail. They are reference reading rather than navigation; the two child collections above are the route to parts.
A detailed reference covering Series I engine variants (1.6-litre and 2.0-litre petrol, 2.0-litre diesel), chassis design, wheelbase evolution, and the critical parts considerations for accurate restoration. Relevant for anyone sourcing components for a Series I vehicle or confirming specifications before ordering.
Series I engine and restoration guide →Covers the engineering and production history of Series II, IIA, and III models, including key differences between generations, engine fitment across sub-variants, and why certain parts are interchangeable while others are not. Useful background before selecting parts from the Series 2 and 3 collection.
Series II, IIA and III restoration guide →These are four successive generations of the same utility vehicle family, each sharing the core body-on-frame architecture but differing in engine, bodywork, and specification. Series I ran from 1948 to 1958 and used a 1.6-litre then 2.0-litre petrol engine, with a diesel option from 1957. Series II ran from 1958 to 1961 and introduced a revised body style. Series IIA ran from 1961 to 1971 and is the highest-volume production variant, available with 2.25-litre petrol and diesel engines and, in certain long wheelbase models, a 2.6-litre straight-six. Series III ran from 1971 to 1985 and brought minor updates including a revised instrument panel and an optional 3.5-litre V8 in select variants. Understanding which generation you have is the essential first step in selecting the correct parts.
Some parts are shared across Series IIA and Series III, particularly engine internals for the 2.25-litre petrol and diesel units, and certain axle and drivetrain components. However, body panels, wiring configurations, and some suspension components differ between generations. Parts shared across Series II and Series IIA are sometimes also different from early and late Series III specifications. The safest approach is to confirm fitment by generation and wheelbase before ordering, and to use the Series 2 and 3 parts collection for those specific generations.
Yes, significantly. Series I vehicles used different wheelbase dimensions (80, 86, 88, and 107 inches depending on year), different body construction details, and earlier engine specifications including the 1.6-litre petrol and the pre-2.25-litre 2.0-litre units. Many body, chassis, and mechanical components are unique to the Series I and do not carry across to Series II or later. The Series 1 parts collection is dedicated to this generation.
Start by identifying which generation your vehicle is. Series I (1948 to 1958) parts are unique to that generation in body, chassis and engine, and live in the Series 1 collection. Series II (1958 to 1961), Series IIA (1961 to 1971) and Series III (1971 to 1985) share considerable parts overlap and are grouped together in the Series 2 and 3 collection. If you are not sure which generation you have, the Commission Number on the bulkhead plate will tell you, and the child collections cover identification in more detail. Use the generation grid above to navigate to the correct collection for your vehicle.
Yes. The Series Land Rover aftermarket is one of the most active classic vehicle parts ecosystems in Europe. New replacement parts are produced for all four generations across the major categories: engine internals for the 2.25-litre petrol and diesel and the 2.0-litre Series I engines, body panels and chassis sections, electrical and wiring components, brake and suspension parts, and full restoration hardware. Genuine Land Rover stock is limited for parts of this age, but OEM-specification parts and quality aftermarket equivalents cover the majority of components in active demand. Specialist UK and EU manufacturers continue to remanufacture Series-specific items, and Budget Parts sources from this network for items not held in catalogue stock.
Start with three steps. First, identify your generation precisely (Series I, II, IIA or III) and your wheelbase, because every parts decision flows from those two facts. Second, work through a baseline service of consumables and wear items: brakes, fluids, filters, ignition components on petrol engines, glow plugs and fuel filters on diesels. Third, plan ahead for the higher-cost restoration items that often surface on Series vehicles after a few months of use, such as bulkhead repair sections, chassis outriggers, swivel housings and gearbox components. The two child collections (Series 1, and Series 2 and 3) hold the parts. The Series I and Series II/IIA/III restoration guides linked below cover the engineering background, common faults and parts priorities for each generation in more depth.