Land Rover Series Parts

Ensure reliable fuel delivery with this replacement diaphragm and notched shaft, designed specifically for AEU2760 fuel pumps. Featuring a T-bar no...

Exhaust Valve Guide is pressed into the cylinder head to support and align the exhaust valve. It locates the valve stem so the valve seats squarel...

Plain Washer - imperial-dimensioned flat washer with an internal diameter of 7/16 inch and an outer diameter of 13/16 inch. Used in general fasten...

Lamp Guard - Round - 73mm - a protective guard that fits over a round 73 mm lamp to shield the lens. It clamps over the light unit to protect the ...

Hex-head bolt, 5/16" UNC thread, 1" long. Unified Coarse (UNC) thread form with a hexagonal head for use with standard imperial spanners and socke...

Reverse Lamp Lens is the clear lens that fits to the rear reverse (reversing) lamp assembly. It seals over the bulb and reflector and diffuses the...

Differential Carrier Bearing is a taper roller bearing that supports the differential carrier within the axle, as part of the crownwheel and pinion...

T-Piece is a three-way connector in the windscreen washer fluid circuit. It joins the washer hose into two branches, distributing fluid from the p...

Brake Pipe Clip secures and routes rigid brake pipes along the chassis within the braking system, holding them in position and guarding against cha...

Exhaust pipe clamp 2.6 Stage 1 V8

Door Bottom Seal for the front door. This rubber seal fits along the lower edge of the door, closing the gap between the door bottom and the body t...

Mirror Arm within the external rear-view mirror assembly. This arm mounts at the door hinge position and extends outward to position the mirror he...

Brake Union – a threaded fitting in the hydraulic brake circuit that joins and seals brake pipe. Female union with a 7/16"-20 UNF thread, sized fo...

Gear Knob - LT95 is the hand grip fitted to the main gear lever of the LT95 4-speed gearbox. It threads onto the top of the gear lever and provide...

Hub Cap fits over the end of the front or rear hub, enclosing the drive flange and hub assembly. It closes off the outer end of the hub to retain ...

Distributor - contact-breaker (points) ignition distributor for the 4-cylinder petrol engine. Distributes the high-tension spark to the cylinders ...

Starter Motor for the 2.5L 4-cylinder diesel engine, part of the engine electrical starting circuit. When the ignition is operated the solenoid th...

Filler Plug sealing the fill and bleed point of the engine cooling system, fitted to the thermostat housing and the radiator. This plastic plug cl...

Crankshaft Rear Oil Seal for the engine bottom end, fitted at the rear of the crankshaft where it exits the block towards the flywheel. The seal r...

Cellular Dynamic Shock Absorber A long-travel front damper that controls axle movement within the suspension, mounted between the chassis and the f...

Tow Ball Step is a rear access step that locates over the tow ball, providing two tread levels to make reaching the rear door, load area or roof ea...

Brake Hose Kit is a three-hose set of standard-length stainless-steel braided brake hoses that replace the flexible sections of the hydraulic brake...

Rear Door Hinge Pin Kit in stainless steel - a complete repair set for the rear (side-hung) door hinges, replacing corroded or worn hinge pins toge...

Bolt - threaded fastener with a 7/16" UNF (Unified National Fine) thread and a 2-1/4" length.

Bolt with a 5/16" UNF (Unified National Fine) imperial thread and a 1-1/2" shank length. A hex-head fastener for general assembly and fixing appli...

Special Fixing Washer for the hardtop side-frame mounting. Seats over the M8 side-frame mounting stud and under its securing nut, spreading the cl...

Exhaust Manifold Stud secures the manifold to the cylinder head on the 4-cylinder engine. It threads into the head and carries the manifold flange...

Sedimentor Sealing Ring for the diesel fuel filter and sedimentor assembly. The sedimentor separates water and sediment from the diesel fuel befor...

Chassis Shackle Bush – Front is the compliant bush at the chassis end of the front spring shackle, part of the leaf spring suspension mounting. Th...

Exhaust Clamp Plate for the exhaust system, used at the front-pipe and catalyst joint. The plate works together with a U-bolt to draw the exhaust c...

Shakeproof Washer – a serrated, externally toothed lock washer used at the clutch hydraulic hose union. The teeth bite into both the mating surfac...

Inlet manifold stud

Ignition Coil for the V8 petrol ignition system. It converts the low-voltage supply into the high-tension voltage that fires the spark plugs throug...

Gearbox Gasket Set for the LT95 four-speed gearbox fitted behind the V8 petrol engine. The LT95 is a combined main gearbox and transfer unit. The ...

Synchro Cone – LT76 is a synchroniser ring from the synchromesh assembly of the LT76 manual gearbox. It is the friction component that brings the g...

Heater Hose for the front of the heater circuit, carrying engine coolant between the engine feed and the heater unit. This flat-section hose forms...

Heater Hose for the rear of the heater circuit, carrying engine coolant between the heater pipe and the heater unit. This flat-section hose forms ...

Track Rod & Steering Damper Bush for the steering linkage, locating the steering damper at its mounting eye. The bush insulates the damper mou...

Oil Filler Cap O-Ring seals the oil filler cap to the rocker cover. It forms an oil-tight seal at the cap-to-cover joint, preventing oil leakage a...

Timing Chain Locking Plate for the timing chain drive of the 2.25L and 2.5L 4-cylinder petrol engine. The plate locks the camshaft sprocket retain...

Fuel Pipe Olive for the fuel supply line. The olive is the compression ferrule that seats between the fuel pipe and its union fitting. When the un...

O-Ring for the engine sump, part of the engine lubrication sealing arrangement. Seals the sump joint to prevent oil leakage. Fitted to four-cylind...

Swivel Housing Stud with 7/16" BSF thread, fitted to the lower face of the front axle swivel housing. The stud secures the lower swivel pin bracke...

Gearbox Thrust Washer for the intermediate gear (laygear) in the main gearbox, used on 4-cylinder applications. It locates against the intermediat...

Interior Door Lock Button, right-hand, of the interior door furniture. The thumbscrew-type lock button that operates the door lock from inside the...

Window Channel for the front door sliding side window assembly. This aluminium channel runs along the front face of the sliding window and retains...

Cable Grommet for the wiring loom, fitting a 41.5 mm panel hole and accepting a cable of up to 6 mm. Made of black rubber, it lines the hole where...

Lock Washer for the starting dog at the front of the crankshaft. The starting dog threads into the nose of the crankshaft to retain the front pull...