Land Rover Series Parts

Drain Plug for the axle casing and fuel tank. This brass threaded plug seals the drain aperture at the bottom of the differential and axle casing,...

Battery Cover - the protective cover fitted over the battery in the engine bay. It shields the battery casing and terminals from debris and accide...

Brake Light Switch, hydraulic (pressure-operated) type, within the brake light circuit. It threads into the brake hydraulic system and has a metric...

Tow Ball 50mm flange-fixing tow ball for use with a bolt-on tow bar drop plate. Rated for a maximum gross trailer weight of 3.5 tonnes, with a D-v...

Starter Motor for the 2.25L 4-cylinder diesel engine, operating in the engine starting circuit. When energised through the starter solenoid, the p...

Reverse lamp switch LT85 V8

Clutch Master Cylinder Overhaul Kit

Swivel Housing Repair Kit for the front axle swivel assembly, covering one side of the axle. This kit excludes the swivel housing itself and suppli...

Front door hinge fixing kit used within the body door hinge mounting assembly. The kit provides the required fasteners and mounting components to...

Ignition Coil A high-output sports coil for the ignition circuit. It sits between the low-tension supply and the distributor, converting the primar...

Door aperture sealing rubber supplied in a continuous 30 metre roll for use within the body sealing system. This profile installs along the door a...

Inline Fuel Filter for petrol engines, fitted in the low-pressure fuel supply line between the tank and the fuel pump or carburettor. This sealed ...

Filler Strip Spacer for the door top, fitting at the vertical joint of the door-top glass frame. The strip fills and finishes the vertical gap in ...

Spare Wheel Buffer for a bonnet-mounted spare wheel. This moulded rubber buffer fits to the bonnet panel and bears against the back of the spare wh...

Accelerator Cable in the throttle control linkage, connecting the accelerator pedal to the carburettor throttle spindle. Transmits pedal movement ...

Piston Ring Set Standard. 2.25 / 2.5 Diesel (Per Piston)

Main Bearing Set - crankshaft main bearing shells for the 2.25L four-cylinder three-bearing engine. The main bearings support the crankshaft withi...

Pinion Bearing (Outer) for the Salisbury axle differential. It is the outer of the pair of taper roller bearings that carry the drive pinion, seate...

Diesel Injector for the fuel injection system, delivering metered, atomised fuel from the injection pump into the engine. Fitted to the 2.25L and ...

Leather hasp civilian

Bolt - a hexagonal-head bolt with an M10 metric thread and a 30 mm length. A common general-purpose fastener used at fixing points across the suspe...

Washer is a large plain flat washer used as a general-purpose load-spreading fastening component, sized for M6 fixings with a wider outside diamete...

Inlet Valve for the cylinder head of the 2.25L 4-cylinder petrol engine, with a 44.5mm head diameter. It seats in the inlet port of the combustion...

Door Pillar Repair Bracket for the front right-hand (offside) door pillar. A welded repair section that renews the front door pillar at the bulkhe...

Electronic Distributor for the ignition system of the 4-cylinder petrol engine. It distributes high-tension voltage from the ignition coil to each...

Differential Bearing for the Salisbury axle. It is one of the pair of taper roller bearings that carry the differential carrier - the housing holdi...

Battery Cover is the top fixing frame of the battery securing assembly. It clamps down over the top of the battery and bolts to the battery tray, h...

Waterpump pulley

Demister Tube

Mounting assy Defender 7A752070 to BA407819

Glow Plug for the 2.25L diesel engine running a parallel (converted) glow plug system. Part of the cold-start pre-heating circuit. The glow plug h...

Pillar seal

Stud for the front axle swivel pin housing - a threaded stud that provides a fixed anchor for fastening a mating component to the swivel pin housin...

Bolt - 3/8" UNF x 4-1/4" is a structural fixing used in the front bumper and chassis frame assembly. It secures the front bumper and frame mountin...

Changeover Relay - 5-Pin - Green is a standard 5-pin changeover relay used across multiple electrical circuits. This relay is used in various appl...

Exhaust manifold stud

Water Pump for the engine cooling circuit of the 2.5L 4-cylinder naturally aspirated diesel, petrol and pre-TDi turbo diesel engines. Belt-driven f...

set screw, Bolt 3/8" UNF x 7/8"

Set Screw - a fully threaded hexagonal-head setscrew with a 5/16" UNF (Unified Fine) imperial thread and a 1-1/8" length. Used as an engine and cha...

Bolt is a general-purpose imperial-thread fixing with a 5/16-inch UNC (Unified Coarse) thread and a 7/8-inch length. Used as a common fastener acr...

Pan Head Screw - a machine screw with a low, rounded-top head and a flat bearing face, used as a general-purpose fixing. Metric M5 thread with a 1...

Differential Cover for the Salisbury rear axle. The cover bolts to the rear face of the axle casing, enclosing the crown wheel and differential and...

Diesel startermotor military reconditioned EXCHANGE!!

Piston Ring Set for the 2.25L and 2.5L naturally aspirated diesel engine, supplying the ring pack for one piston. The rings seat in the piston rin...

Lock Washer secures the retaining hardware on the layshaft (countershaft) within the manual gearbox. A tab on the washer is folded against the ret...

Mainshaft Peg is a locating peg fitted to the mainshaft of the LT67 gearbox. It positions and retains its associated component on the gearbox main...

Con Rod Bearing Set - connecting rod big-end bearing shells for the 2.25L four-cylinder engine. The con rod bearings sit between the connecting ro...

Split Pin - a cotter pin used to lock a slotted (castle) nut or to retain a clevis pin. Passed through a drilled cross-hole in the shank or the nu...