Land Rover Series Parts

Wiper Arm - windscreen wiper arm, right-hand, wide pattern. The 7mm is the wide width of the arm, which sets the wiper-blade fitting - it is not a...

Air cleaner to carburettor hose

Accelerator Cable for the throttle control linkage, transmitting accelerator pedal movement to the carburettor throttle on the 2.25 litre petrol en...

Rear Crossmember is the transverse structural section that closes and reinforces the rear of the chassis frame. Because mud, road salt and debris c...

Track Rod Tube is the central bar of the steering track rod within the front steering linkage. Its threaded ends accept the track rod ends, joinin...

Blind Nutsert (M6) is a threaded insert that provides an M6 female thread in thin sheet metal or panels where the rear face is not accessible. It ...

Tailgate Hinge for the left-hand side, the lower hinge on which the drop-down tailboard pivots. It carries one side of the tailboard along its low...

Tailgate Hinge for the right-hand side, the lower hinge on which the drop-down tailboard pivots. It carries one side of the tailboard along its lo...

Seat Base Cushion for the inner (centre) position of the 3-person front bench seat assembly. Constructed with a foam core upholstered in black vin...

Washer is a plain flat washer used as a general-purpose load-spreading fastening component, with a 6 mm internal diameter and a 15 mm outside diame...

Spare Wheel Bonnet Buffer is a rubber buffer for the bonnet-mounted spare wheel carrier. It sits between the spare wheel and the bonnet, cushionin...

Body is the right-hand sill channel for the Defender, running along the underside of the door aperture in the body structure. This structural chan...

Locking Plate - the lower tailboard locking plate, mounted to the rear body. Fitted at the lower hinged tailboard, the plate provides the fixed en...

Clutch Slave Cylinder, part of the hydraulic clutch release circuit. The slave cylinder receives fluid pressure from the clutch master cylinder an...

Transfer Case Bottom Cover Gasket for the LT95 combined gearbox and transfer case. It seals the joint between the bottom cover and the transfer ca...

O-Ring - LT95 Gearbox seals the transfer shaft on the LT95 4-speed gearbox, which carries an integral transfer case, preventing oil leakage at the ...

Stub Axle - rear stub axle carrying the hub and bearings at the rear axle. Bolted to the rear axle casing, it forms the fixed spindle on which the...

Swivel Pin Housing for the front axle, the chrome-finished swivel joint on which the steering swivel and hub assembly pivot. The housing bolts to ...

Rubber-Lined Sealing Washer - a metal sealing washer with a bonded rubber lining, fitted under a bolt or union to seal the joint. As the fitting i...

Electronic Conversion Kit - electronic ignition conversion for the 4-cylinder petrol points distributor. Replaces the contact breaker points and c...

Piston for the 2.25L four-cylinder diesel engine, forming part of the piston and connecting rod assembly within the cylinder block. Supplied at +0...

Gasket

Crankshaft Oil Seal - Rear seals the rear of the crankshaft where it leaves the cylinder block at the flywheel end, retaining oil within the bottom...

Breather and oil filler cap for the rocker cover, part of the engine crankcase ventilation system on the 2.25L and 2.5L 4-cylinder petrol and natur...

Gasket

Coolant Hose for the V8 carburettor petrol engine cooling circuit. It carries engine coolant between components of the cooling system, moulded to s...

Viscous Fan Coupling is the temperature-controlled drive unit between the water pump and the engine cooling fan. It mounts on the water pump shaft...

Fan Belt - V-belt for the 2.6L 6-cylinder engine, driving the cooling fan and compressor. Fitted to the accessory drive system of the 2.6L engine....

Connecting Rod Nut - the big-end nut that secures the connecting rod cap to the rod bolts. The nut clamps the connecting rod bearing cap onto the ...

Steering Wheel is a 15-inch three-spoke replacement wheel that mounts to the steering column. It is supplied without a boss, so a separate fitting...

Radiator Muff for Series 2A (late models with headlights in the wings) and Series 3 Land Rovers, with black-edged trim. This muff fits across the ...

Side lamp new type

Blanking Plug for closing a 1-5/8" hole in bodywork or panels. Seals an unused aperture or grommet hole in body panels, brackets and pedal/electri...

Seat belt bracket RH

Screw – a black self-tapping screw with a pan head and Pozidriv drive recess, size No. 10 × 5/8 in, used to secure body, trim and panel fixings. B...

Headlamp Screw is a fastener used in the front headlamp assembly. It secures the headlamp unit and rim within their mounting, holding the lamp in ...

Carb overhaul kit 175CD V8 Zenith Stromberg

Mainshaft peg

Coolant Pipe Adaptor for the engine cooling circuit. It threads into the thermostat housing / cylinder head coolant outlet to provide the connectio...

Fuel Tank Sender for the rear-mounted fuel tank on long-wheelbase diesel applications. The sender unit fits into the top of the fuel tank, where a...

Differential Bearing for the Salisbury axle. It is one of the pair of taper roller bearings that carry the differential carrier - the housing holdi...

Diff Pinion Taper Roller Bearing is the inner pinion taper roller bearing in the Salisbury axle differential. It supports the pinion shaft where i...

Bearing used across several Land Rover drivetrain assemblies: the LT230 transfer box, where it supports the high and low range gear; the LT95 gearb...

Engine Overhaul Gasket Set for the 2.6 litre IOE (inlet-over-exhaust) 6-cylinder petrol engine. A set of the gaskets and seals used when stripping...

Cup Plug (core plug) for the front face of the Rover V8 cylinder head. This pressed-steel cup plug seals the front casting gallery in the Rover 3....

Main Bearing Cap Bolt - a 1/2" UNC bolt that fastens a main bearing cap to the cylinder block on the Rover V8 engine. It clamps the main bearing c...

Headlamp Pigtail connector lead for the front lighting circuit. The pigtail plugs onto the rear of the headlamp unit and links it to the vehicle's...

Needle Roller Bearing for the transfer box intermediate gear. The bearing carries the intermediate gear on its shaft within the gear cluster, allo...