Land Rover Series Parts

Free-Wheeling Hub Repair Kit for 24-spline manual free-wheeling hubs. Manual free-wheeling hubs allow the front drive members to be disengaged fro...

Centre Retainer - Front Windscreen Glass is the metal retainer strip that secures the front windscreen glass at its centre division point. The ret...

Corner Capping - galvanised - right-hand (offside) roof corner. This galvanised steel capping fits over the offside rear roof corner, covering and...

Lock Stop Bolt, Front Axle sets the steering lock stop on the front axle. Its head contacts the stop face on the axle to limit swivel travel, cappi...

Set Screw - a fully threaded hexagonal-head setscrew with an M10 metric thread and a 20 mm length. A general-purpose fixing used at fastening point...

Bolt - a hexagonal-head bolt with an M6 metric thread and a 30 mm length. A common general-purpose fastener used at fixing points across the vehicl...

Plain Washer - Large 5/16" is a large plain washer for use with 5/16" fastenings, providing load distribution beneath bolt heads and nuts across La...

Floor-Mounted Headlamp Dipswitch for Land Rover Series 2A vehicles. This foot-operated switch mounts to the cab floor and controls switching betwe...

Seat Box End Panel - Right-Hand is a repair panel forming the outer end face of the seat box assembly. It replaces the corroded offside end panel ...

Door Pillar Repair Bracket for the front left-hand (nearside) door pillar. A welded repair section that renews the front door pillar at the bulkhe...

Bolt Fixing bolt, 3/8" UNF x 2-1/2", used to secure the rear fuel tank to the chassis.

seal washer for block coolant drain plug. - All 4-cylinder engines upto 1998 (except VM diesel)

Gearbox Tie Rod Buffer for the gearbox steady (tie rod) mounting. The tie rod restrains the gearbox against fore-and-aft movement under load. This...

U-Bolt for the front axle leaf-spring mounting - the square-bend form. The U-bolt passes over the front axle and down through the spring plate, cl...

Window Catch Mask fits behind the window catch on the rear side door. This plate seats between the catch and the door skin, masking and reinforcin...

Exhaust Valve for the cylinder head valvetrain of the 2.25L and 2.5L naturally aspirated 4-cylinder diesel engines. The valve seals against its se...

Circlip for the handbrake (parking brake) linkage. This external retaining circlip secures the handbrake relay elbow onto its pivot post, holding t...

Fitment: All Models Except TD5

Steering Box Cover for the steering box, for right-hand-drive (RHD) applications. The cover plate bolts onto the steering box housing, enclosing a...

Con Rod Bearing Set - connecting rod big-end bearing shells for the 2.25L four-cylinder engine. The con rod bearings sit between the connecting ro...

Number Plate Lamp for the rear number plate lighting circuit. This complete lamp assembly mounts at the rear of the vehicle to illuminate the numb...

Spring Washer for use across a wide range of fixings and assembly applications on Land Rover vehicles. This split-ring spring washer is placed ben...

Engine Stud is a threaded fastening stud used in the cylinder head and manifold assemblies of the four-cylinder engine. It provides the fixed thre...

Rear Quarter Panel for the right-hand side, part of the rear body structure. This is the outer body panel that forms the rear side of the vehicle ...

Cylinder Head Gasket - 2.6L 6-Cylinder seals the joint between the cylinder head and the engine block on the Rover 2.6L inline six-cylinder IOE (in...

Exhaust Valve for the 2.6L 6-cylinder IOE (inlet-over-exhaust) petrol engine, forming part of the cylinder head and block valvetrain. The exhaust ...

Master Cylinder Repair Kit - CB Type - Non-Servo is an overhaul kit for the single-line, non-servo CB-type brake master cylinder fitted to short-wh...

Screw 3/8" UNC x 1-1/2" used to secure the starter motor to the engine block on Rover V8 petrol engine applications. This is a 3/8 inch Unified Nat...

Bolt - 7/16" UNF x 1-1/2" imperial hex-head fastener for use in axle, suspension, and body or chassis applications requiring 7/16" UNF imperial thr...

Screw hex HD 3/8" UNC x 1-1/4"

Hex Bolt - a hexagonal-head bolt with an M6 metric thread and a 12 mm length, manufactured to property class 8.8. Class 8.8 is a medium-carbon ste...

Land Rover Series III Parts Catalogue, an illustrated reprint published by Brooklands Books Ltd. It reproduces the factory parts catalogue for the ...

Engine Plug - a threaded blanking plug used to seal machined ports and drillings in the engine, including locations in the cylinder head and the oi...

Rotor Arm - Ducellier Type for the ignition distributor assembly. This rotor arm fits the Ducellier-type distributor and rotates inside the distri...

Floor-Mounted Headlamp Dipswitch for Land Rover Series 2A vehicles. This foot-operated switch mounts to the cab floor and controls switching betwe...

Piston Ring Set for the 2.25L and 2.5L 4-cylinder petrol engine, supplying the ring pack for one piston. The rings seat in the piston ring grooves...

Distributor Cap for the 2.6L 6-cylinder petrol ignition system on the Land Rover Series III. Fitted over the distributor body, the cap receives hi...

Spark Plug - ignites the air/fuel mixture in the combustion chamber of the petrol engine. It threads into the cylinder head with its electrode gap ...

Master Cylinder Reservoir Cap seals the fluid reservoir on the brake or clutch master cylinder. It screws or presses onto the reservoir neck to re...

Water Pump O-Ring forms the coolant seal between the water pump and the engine front cover, within the cooling circuit. It seats in the water pump...

Washer Thrust 3rd Gear

Rear Spring Dowel - a locating dowel that positions the rear road spring on its seat. The dowel engages a corresponding hole in the base of the sp...

Fuel Gauge is a 12V dash-mounted instrument that displays the amount of fuel remaining in the tank. Fitted within the instrument panel, it receive...

Hex nut

Left-Hand Exhaust Downpipe for the 3.5L V8 EFI engine, non-catalyst exhaust configuration. Connects the left cylinder bank exhaust manifold outlet ...

Plate - LH is the rear axle brake pipe shield (bracket) for the left-hand side. It mounts on the rear axle and shields the rigid brake pipe runnin...

Plate - RH is the rear axle brake pipe shield (bracket) for the right-hand side. It mounts on the rear axle and shields the rigid brake pipe runni...

Fuel Tank Drain Plug - the threaded plug that seals the drain point at the base of the fuel tank. Removing it allows the tank to be drained for se...