for Discounts / VAT
for Discounts & Correct VAT
Land Rover suspension parts cover the full system that controls wheel motion, ride height and steering across the Defender, Discovery, Range Rover, Range Rover Sport, Freelander and Series ranges.
Air suspension is the standard or common fit across the modern independent-suspension range: Discovery 3, 4 and 5, Range Rover L322, L405, L460 and Velar, Range Rover Sport L320, L494 and L461, and the current Defender L663. Several of these were also offered with coil springs on lower specifications, so always confirm the fitted setup. Earlier air systems ran on the Range Rover P38A, the late Range Rover Classic LSE and self-levelling Discovery 2 models. The classic leaf-sprung Series, and the coil-sprung Classic Defender, Discovery 1, most Range Rover Classics and Freelander, use steel springs. Stocked items are dispatched from our Dutch warehouse network.
Anti-Roll Bar Bush locates the anti-roll bar at its mounting to the chassis, holding the bar in position while allowing it to rotate as the suspens...
View full detailsPolyurethane Suspension Bush Kit - Classic Red grade. This kit replaces the original rubber suspension bushes with polyurethane items in the Polyb...
View full detailsSwivel Pin Bearing is the upper needle-roller thrust bearing in the front axle swivel housing assembly. It mounts on the upper swivel pin and carr...
View full detailsRetainer for the steering damper mounting, part of the track rod and steering damper assembly. This stem washer locates on the steering damper mou...
View full detailsPolyurethane Suspension Bush Set in the black compound, for the front and rear coil-sprung suspension. This is a full-vehicle set that replaces the...
View full detailsRear Spring Spacer Kit for the coil-spring rear suspension, supplied as a pair of blocks that fit between the axle and the spring seats to raise ri...
View full detailsFront Half Shaft Pair for the front axle drive, transmitting torque from the front differential out through the axle casing to the wheel hubs. The...
View full detailsPair of Heavy Duty Rear Half Shafts for 90/Discovery 1/RRC 1994 On & 110/130 2002 On
Terrafirma rear spring retaining plates 90/D1/RRC
Front Shock Absorber for the front axle suspension assembly, controlling vertical wheel movement and stabilising the coil spring through compressio...
View full detailsNyloc Locknut - M6 - M6 hex nyloc (nylon insert) locknut. The nylon insert grips the bolt thread to resist loosening under vibration without requi...
View full detailsTrack Rod Washer from the steering linkage. It seats at the track rod fixing, spreading clamp load beneath the retaining nut to secure the joint.
Axle Spring Mount forms the lower seat for the rear coil spring, welding onto the rear axle casing to locate and retain the base of the spring. Th...
View full detailsPower Steering Box - recirculating-ball steering gear of the Adwest Lightweight type, forming the core of the hydraulically assisted steering circu...
View full detailsPolybush kit 2 ORANGE D1/RRC 1986 ON & DEF 1994 ON
Panhard Rod for the front axle, part of the live-axle suspension linkage. The Panhard rod connects the axle to the chassis on one side and locates...
View full detailsLinkage
Rear Coil Spring is a suspension component within the rear coil spring assembly. It supports the vehicle's weight at the rear axle and maintains r...
View full detailsAdjustable Panhard Rod - lateral axle locating link within the suspension assembly. The Panhard rod ties the axle to the chassis and controls side...
View full detailsBush Kit Pro-Comp Only BR 2255PK
Drag Link for the front live axle steering circuit. The drag link connects the steering box drop arm to the front axle steering arm, transmitting ...
View full detailsDifferential Bearing Shim for the differential carrier assembly, fitted behind the differential side bearing to control bearing preload and set the...
View full detailsTrack rod end pin nut for the steering linkage. Secures the tapered pin of the TRE 80 track rod end into the steering arm eye, clamping the taper ...
View full detailsFitment: Defender van 1994 tot 2007 Discovery 1 van 1989 tot 1994 Range rover Classic
Terrafirma diff guard 90/110/130/D1/RRCFront for RHD & LHD vehicles
Hydraulic Bump Stop Mounting Kit - Rear is the rear-axle mounting hardware for a hydraulic bump stop installation, sitting within the suspension bu...
View full detailsHydraulic Bump Stop Mounting Kit - Front is the front-axle mounting hardware for a hydraulic bump stop installation, sitting within the suspension ...
View full detailsCreeper Joint Rear Radius Arms (PR) for 90/110/130/Discovery 1/RRC
Radius Arm - front axle locating link in the coil-sprung front suspension, tying the front axle to the chassis and controlling fore-and-aft axle lo...
View full detailsLong-Travel Spring Relocation Cone - replaces the standard coil spring seat so the spring can dislocate (drop out of its seat) at full axle droop a...
View full detailsTop Shock Mount - upper shock absorber mounting for extreme long-travel suspension. This mount repositions the upper shock pickup point to accept ...
View full detailsCranked Rear Radius Arm - links the rear axle to the chassis, controlling fore-and-aft axle location and reacting drive and braking torque. The cr...
View full detailsRadius Arm - front axle locating link in the coil-sprung front suspension. The radius arm ties the front axle to the chassis, controlling fore-and-...
View full detailsShock Turret forms the upper mounting point for the front shock absorber on the chassis, within the front suspension assembly. Tubular fabricated ...
View full detailsSpring Dislocation Cones - Front are fitted inside the front coil springs to prevent spring dislocation under maximum suspension droop. During extr...
View full detailsRear Shock Absorber damps the rear suspension within the suspension assembly, valved for a +2" (50mm) raised ride height. Offers 8-stage adjustabl...
View full detailsFront Shock Absorber damps the front suspension within the suspension assembly, valved for a +2" (50mm) raised ride height. Fitted with a remote r...
View full detailsSteering Rods - 4 Track Rod Ends - Discovery 1/RRC
Hydraulic Bump Stop & Mounting Kit is a complete progressive end-of-travel control package for the suspension, combining four hydraulic bump st...
View full detailsShock Absorber - front suspension damper with four-stage adjustable damping, sized for +2 inch raised ride height. Fitted between the chassis and ...
View full detailsRear Shock Absorber for the rear axle suspension, damping spring oscillation and controlling vertical wheel movement between the rear axle housing ...
View full detailsFront Shock Absorber for the front axle suspension, damping spring oscillation and controlling vertical wheel movement between the front axle housi...
View full detailsExtreme Long Travel Shock Absorber damps the suspension on vehicles set up for extended axle articulation, controlling spring and wheel movement to...
View full detailsSealing Washer - bonded (Dowty-type) seal for the power steering pump banjo union. The washer is a metal outer ring with a vulcanised elastomeric ...
View full detailsTransfer Box Differential Gear Kit for the centre differential of the LT230 transfer box. The kit renews the centre differential gear set, which s...
View full detailsSteering Tube is the longitudinal tube assembly within the steering linkage. It forms part of the rod-and-relay steering system, transmitting move...
View full detailsTrack Rod Assembly in the front steering linkage. The track rod links the front steering arms so that both road wheels turn together, transmitting...
View full detailsTrack Rod Clamp secures the adjustable joint of the steering track rod. Fitted around the split end of the rod, it pinches the threaded sleeve clos...
View full detailsSystem Overview
The suspension and steering system on a Land Rover or Range Rover does two jobs at once. It manages wheel motion across varied terrain, and it keeps the contact patch in the geometry the chassis was designed for. When either job slips, drivers notice it first through the steering wheel and through tyre wear patterns.
Vehicle use affects wear, but not in a fixed pattern. Heavy loads, towing, potholes, off-road contamination and unresolved air leaks all push wear into different parts. Model, suspension type, age and maintenance change the picture too, so diagnose by symptom rather than assuming a particular failure order.
This collection holds the replacement parts across Defender, Discovery, Range Rover, Freelander and Series models, with model-scoped fitment support where the system varies meaningfully between generations.
Shop by Part TypeThe suspension, steering and axle system breaks down into nine part groups. Jump straight to the category that matches your job, or read the system overview below if you are diagnosing by symptom.
Dampers, struts and off-road coilovers with fitting hardware.
Land Rover shock absorbers and dampersStandard, heavy-duty and lift springs with seats and isolators.
Land Rover coil springs and lift kitsAir springs, compressors and ride height sensors for EAS-equipped models.
Land Rover air suspension parts and compressorsRadius arms, control arms, wishbones and trailing links.
Land Rover suspension arms and control armsBush kits, poly bushes, anti-roll bar links and rubber mounts.
Land Rover suspension bushes and anti-roll bar kitsA-frame, control arm and drop link ball joints, boots and repair kits.
Land Rover ball joints and repair kitsTrack rod ends, tie rods, steering dampers, racks and PAS parts.
Land Rover steering components and track rodsHub assemblies, taper bearings, hub nuts and oil seals.
Land Rover wheel bearings and sealsSwivel kits, stub axles, half shafts and drive flanges.
Land Rover axle and swivel partsControl arms locate the wheel hub against the chassis and carry the bushes that absorb vibration and small geometry movement. On the double-wishbone front suspension layouts (Discovery 3 and 4, Range Rover L405 and L460, Range Rover Sport L320, L494 and L461), lower arm bush wear is a common issue. Drivers report a clunk during braking, during steering lock, or when the suspension loads under bumps. The Range Rover L322 uses a strut-type front instead, where the air strut, transverse link and compression link are the common service areas.
The decision when ordering is between pressed-bush replacement and a complete arm assembly. Pressed bushes cost less in parts but require the correct press equipment and a structurally sound original arm. An aged or corroded arm often justifies replacing the complete assembly on labour and reliability grounds.
Wheel bearing construction varies by model, axle, build and VIN. Many later independent-suspension models use a bolt-on hub assembly where the bearing and hub are renewed as one unit, but others use a sealed bearing pressed into the carrier, and the front and rear can differ on the same vehicle (the Freelander 2 is a good example). Older platforms such as the Series, Defender Classic, Discovery 1 and Range Rover Classic use serviceable opposed taper roller bearings that can be cleaned, re-greased and adjusted. Check how your bearing is supplied before ordering.
A failing hub or bearing typically presents as a hum that rises with road speed and changes character on a steering input. Where the vehicle uses a bolt-on unit, replacement is straightforward because the assembly unbolts from the upright; where the bearing is pressed into the carrier it needs pressing out and in. See the wheel bearings and seals collection for the full range.
The steering rack converts hand-wheel rotation into linear motion at the tie rod ends. Tie rod ends and inner ball joints wear gradually and can produce play, vague steering and uneven tyre wear before they produce noise. Rack-internal wear and seal leaks tend to appear as excess play found during alignment work, where it cannot be corrected by toe adjustment alone.
Bushes and ball joints can fail on their own, a torn boot, a seized joint or a perished bush is enough, but they often wear alongside the parts around them. Ordering a single ball joint without inspecting the wishbone bush, the anti-roll bar drop link and the opposite side is a common rework trigger. Inspect the adjacent parts while access is open and replace what is worn, scoped to one axle at a time.
Air SuspensionAir suspension is the most complex subsystem in this category and the highest-value replacement decision. It applies to:
The parts that most often need attention on an air system are the air springs and the compressor. Air springs perish and split at the fold points in the rubber bladder and start to leak. A compressor then overworks trying to keep up with that leak and eventually wears out, which is why an unresolved air leak so often takes the compressor with it. Air lines, the valve block and ride height sensors can also fault, though sensors and control electronics frequently last the life of the vehicle. Diagnose each part on its own rather than replacing to a fixed order.
For diagnosis depth on the L320 specifically, see the L320 air suspension fault guide. The blog covers symptom-to-component mapping; this page lists the parts.
Confirm whether your vehicle is on air or coil before ordering. Some Discovery 3 builds left the factory on coil springs, and aftermarket air-to-coil conversions are common and may already have been fitted, so the springs on the vehicle now may not match the original specification. Check from the VIN-linked build record or by looking at the spring at the wheel: an air spring is a tall rubber bladder, a coil is a steel spring.
Suspension parts are returned more often than most categories because fitment varies more than buyers expect. Five checks before ordering save the most labour:
Several parts share labour access, so when one is off it is worth inspecting and, if worn, renewing its neighbour in the same visit. This is about inspection and shared labour, not automatic replacement.
Access matters too. On some models the lower arm runs close to the brake hose and caliper fixings, so it is worth checking the nearby brake parts while access is open. Incorrect alignment after suspension work can also cause rapid or uneven tyre wear.
For owners replacing ball joints, the ball joint failure guide covers the test procedure and the visual checks before ordering replacements.
Buyer ConfidenceThese are the common mistakes behind returns and repeat workshop visits on suspension orders.
When ordering a control arm, check whether it comes with bushes fitted and whether the geometry matches the original. Aftermarket arms sometimes use different bush geometry from OEM, and mixing specifications across an axle can leave the car feeling slightly off even when nothing is worn, so keep the axle consistent.
Correct fitment by model, year and variant is the deciding factor on suspension orders. Land Rover and Range Rover models were produced with multiple suspension configurations across trim levels and markets, and the parts are rarely cross-compatible.
Budget Parts lists parts by model and variant. If the original build configuration is in doubt, the VIN can be used to confirm whether the vehicle left the factory on air or coil suspension, which bearing type, and which steering rack variant.
For fitment questions on a specific vehicle, contact the team with the VIN before ordering. Workshops and trade buyers can request volume pricing and account support, see our trade and volume discount policy.
Technical GuidesFour blog guides on Budget Parts cover the diagnostic and failure-pattern depth that this commercial collection does not. Use the relevant guide alongside the parts list to confirm what to order.
Visual and movement-based tests for worn ball joints across the Discovery and Range Rover range, with the clunk-on-lock pattern that can point to lower ball joint wear on the Discovery 3 and Discovery 4.
Land Rover ball joint symptoms, testing and replacementComponent-by-component breakdown of air spring, compressor and height sensor failure on the L320, with the order in which failures typically cascade.
Range Rover Sport L320 air suspension diagnosisAir suspension, electronics and ancillaries on the 2013 to 2022 L405. Useful for owners diagnosing multi-system faults where suspension is one of several contributors.
Range Rover L405 problems and fixesWheel bearing and rear trailing arm bush pattern specific to the L359 generation, with the typical mileage at which each appears.
Freelander 2 common faults and fixesCommon causes of knocking over uneven surfaces include worn lower ball joints, wishbone bushes or anti-roll bar drop links. A clunk that appears on steering lock can point to a lower ball joint, but it can also come from a CV joint, a track rod end, a top mount, a drop link, the steering stops or a loose fixing, so check play, boots and movement under load before ordering. The relevant parts are listed by model in this collection.
There is no fixed interval. As a broad aftermarket guide, air springs often last around 6 to 10 years or roughly 130,000 to 160,000 kilometres, but climate, use and how often the vehicle is left standing all change that. Leakage, cracking at the folds, a corner that settles overnight, or a compressor that runs longer than it used to are better signs to replace than mileage alone.
Not unless both show wear. Where the vehicle uses a bolt-on hub unit, the hub is renewed as a single unit per wheel; where the bearing is pressed into the carrier it is done individually, and the front and rear can differ on the same vehicle. Inspect the opposite side at the same labour visit, but do not replace it pre-emptively unless there is wear.
The Range Rover Sport L320 (2005 to 2013) came with four-corner air suspension as standard. Many have since been converted to coil springs with aftermarket kits, so the simplest check is the spring at the wheel: an air spring is a tall rubber bladder, a coil is a steel spring. The VIN-linked build record gives the original factory specification.
Check the alignment whenever you replace a geometry-setting part such as a control arm, tie rod end or wishbone, or whenever the repair disturbs the knuckle or the adjustment points. A tie rod replacement always needs it because it changes toe directly. A straightforward bolt-on hub swap that leaves the knuckle undisturbed does not by itself change alignment, but it is still worth a check.
Updated: 13 July 2026