Land Rover Wheel Accessories

Land Rover wheel accessories cover the smaller fitting and finishing parts that go around the wheel rather than the wheel itself: centre caps and hub caps, wheel spacers, tyre pressure sensors, balancing beads, valve hardware and inner tubes. This page brings them together for Series, Defender, Discovery, Range Rover and Freelander owners, so you can find the part that completes a wheel without scrolling past full wheels and nuts. Complete wheel hub assemblies and bearings are drivetrain parts and sit in Land Rover Suspension Parts, not here. Some parts are universal, while centre caps, spacers and sensors are matched to the wheel or vehicle, so check the fit before ordering. Everything here is stocked across our Dutch warehouse network for EU dispatch.

Sort by

View as

FRC4377 - Hub Cap

- €1,70

€1,70

€1,70 - €1,70

€1,70

Aftermarket

68 in stock

Hub Cap fits over the end of the front or rear hub, enclosing the drive flange and hub assembly. It closes off the outer end of the hub to retain ...

View full details

219098 - Drive Shaft Hub Cap

- €1,70

€1,70

€1,70 - €1,70

€1,70

Aftermarket

82 in stock

Drive Shaft Hub Cap for the hub assembly on Land Rover Series vehicles. This cap fits at the outer face of the hub, closing off the drive shaft en...

View full details

GA2232 - Spare wheel carrier - swing-away rear door

- €399,00

€399,00

€399,00 - €399,00

€399,00

Aftermarket

Only 1 left!

Swing-away spare wheel carrier is designed to support and relocate the spare wheel at the rear door, allowing hinged outward movement for improved ...

View full details

FRC4377LR - Hub Cap

- €18,10

€18,10

€18,10 - €18,10

€18,10

Genuine

3 in stock

Hub Cap fits over the end of the front or rear hub, enclosing the drive flange and hub assembly. It closes off the outer end of the hub to retain ...

View full details

GA2027 - Spare wheel cover 235 x 85 x 16 by AftermarketWheel System Part Land Rover Range Rover Defender, Series

GA2027 - Spare Wheel Cover – 235/85 R16

- €36,50

€36,50

€36,50 - €36,50

€36,50

Aftermarket

2 in stock

Spare Wheel Cover in black vinyl, sized to fit a 235/85 R16 spare tyre. The cover fits over an externally mounted spare wheel to shield the tyre a...

View full details

GA2021 - Spare Wheel Cover – 7.50x16 – Soft – Plain

- €37,60

€37,60

€37,60 - €37,60

€37,60

Aftermarket

4 in stock

Spare Wheel Cover for an externally mounted spare wheel sized 7.50x16 (235/85R16). Constructed from soft vinyl, it shields the spare wheel and tyr...

View full details

MRC5627 - Spare Wheel Buffer – Bonnet

- €17,00

€17,00

€17,00 - €17,00

€17,00

OEM

10 in stock

Spare Wheel Buffer for a bonnet-mounted spare wheel. This moulded rubber buffer fits to the bonnet panel and bears against the back of the spare wh...

View full details

576844 - Wheel hub assembly & stud S3 by AftermarketSteering or Suspension Part Land Rover Range Rover Defender, Series

576844 - Wheel Hub Assembly – With Stud

- €124,00

€124,00

€124,00 - €124,00

€124,00

Aftermarket

2 in stock

Wheel Hub Assembly - the complete axle hub, supplied with the wheel studs already fitted. It serves both front and rear hub positions. The hub mou...

View full details

FRC3875 - Wheel Hub Assembly

- €151,00

€151,00

€151,00 - €151,00

€151,00

Aftermarket

Only 1 left!

Wheel Hub Assembly for the front or rear axle, supplied complete with wheel studs. The hub carries the road wheel and rotates on the axle taper be...

View full details

GA2022 - Spare Wheel Cover – 600 x 16

- €36,50

€36,50

€36,50 - €36,50

€36,50

Aftermarket

Available to order: 2-3 weeks delivery

Spare Wheel Cover in plain black vinyl, sized to fit a 600 x 16 spare wheel and tyre (roughly a 195/80 R15 metric equivalent). It slips over the m...

View full details

RRC5035 - Wheel Cap – LH

- €38,90

€38,90

€38,90 - €38,90

€38,90

Aftermarket

Only 1 left!

Wheel Cap - LH for the Freelander 1 wheel arch assembly. This left-hand wheel capping is a trim component that covers and finishes the wheel arch ...

View full details

DA3000 - Inner Tube 7.50 x 16 / 7.00 x 16 (With Small Valve) by Bearmach OEMWheel System Part Land Rover Range Rover Defender, Series

DA3000 - Inner Tube – 7.50 x 16 / 7.00 x 16 – Small Valve

- €26,00

€26,00

€26,00 - €26,00

€26,00

OEM

11 in stock

Inner Tube for 7.50 x 16 and 7.00 x 16 tyres, fitted inside the tyre on tube-type wheels to hold the air pressure. Supplied with a small diameter ...

View full details

593873 - Hub Cap

- €1,80

€1,80

€1,80 - €1,80

€1,80

OEM

3 in stock

Hub Cap for the 101 Forward Control wheel hub. Fits the wheel hub on Series II, IIA, and III 101 Forward Control variants, covering and protecting...

View full details

BA 042AH - Spare Wheel Cover – 205x16 – Hard

- €59,00

€59,00

€59,00 - €59,00

€59,00

Aftermarket

Only 1 left!

Spare Wheel Cover fits over an externally mounted spare wheel to protect the tyre and wheel from weather, road dirt and UV exposure. This is the h...

View full details

DA2026 - Wheel Cover 205 x 16

- €35,50

€35,50

€35,50 - €35,50

€35,50

Aftermarket

Available to order: 2-3 weeks delivery

Wheel Cover 205 x 16

RRC5035LR - Finisher

- €46,60

€46,60

€46,60 - €46,60

€46,60

Genuine

Available to order: 2-3 weeks delivery

Wheel Cap - LH for the Freelander 1 wheel arch assembly. This left-hand wheel capping is a trim component that covers and finishes the wheel arch ...

View full details

GA3000 - Inner Tube – 7.50 x 16 / 7.00 x 16 – Small Valve

- €25,10

€25,10

€25,10 - €25,10

€25,10

Aftermarket

Available to order: 2-3 weeks delivery

Inner Tube for 7.50 x 16 and 7.00 x 16 tyres, fitted inside the tyre on tube-type wheels to hold the air pressure. Supplied with a small diameter ...

View full details

About Land Rover wheel accessories

This collection holds the parts that sit alongside a wheel rather than the wheel and its fixings. That means centre caps and hub caps that cover the centre bore, wheel spacers that push the wheel outward for clearance or a wider track, tyre pressure monitoring sensors on models fitted with them, balancing beads and weights, valve caps and stems, and inner tubes for steel wheels. The wheels themselves, and the nuts and studs that hold them on, sit in their own sections, so this page stays focused on the finishing and fitting parts. It covers Land Rover and Range Rover from the Series and classic Defender through to the later Discovery and Range Rover ranges.

What fits which wheel

A few of these parts are broadly interchangeable. Balancing beads, valve caps and most valve hardware are not tied to a particular model. The rest are matched to the wheel or the vehicle. Centre caps are sized to the wheel's centre bore and to the badge style, so a cap for a steel wheel will not suit a later alloy. Wheel spacers are matched to the hub stud pattern and centre bore, and add a fixed amount of track each side. Tyre pressure sensors are matched to the model, year and radio frequency the vehicle expects. Inner tubes are sized to the wheel and tyre. When a part is size or model dependent, confirm it against your wheel or vehicle before ordering.

Choosing the right part

The quickest way to get the right accessory is to work from the wheel you already have. For a centre cap, measure the opening it pushes into, or quote the part number stamped on the old cap. For a spacer, you need the stud pattern and centre bore of your hub, plus the thickness you want. For a tyre pressure sensor, your model and build year decide the correct type, since fitment changed across generations and left and right hand drive markets. If you are replacing like for like, matching the new part to the old one is the safest check.

Related categories

Frequently asked questions

What counts as a Land Rover wheel accessory?

It is the group of parts that go around a wheel rather than the wheel itself or the nuts that hold it on. That includes centre caps and hub caps, wheel spacers, tyre pressure monitoring sensors, balancing beads and weights, valve caps and stems, and inner tubes. Complete wheels sit in road wheels and spares, and the fixings sit in wheel nuts and locks.

Will Land Rover centre caps fit my wheels?

Centre caps are sized to the centre bore of the wheel and to the badge style, so they are not universal across the range. A cap made for a steel wheel will not suit a later alloy, and sizes changed across models. The safest approach is to measure the opening the cap pushes into, or to quote the part number on your existing cap, before ordering.

How do I choose the right wheel spacers?

Wheel spacers are matched to your hub by stud pattern and centre bore, and they add a set amount of track on each side based on their thickness. Choose the spacer that matches your hub fitment and the clearance you need, and check that your wheel nuts or longer studs still give full thread engagement once fitted. Local road rules on track width and spacers vary, so confirm what is permitted where you drive.

Do tyre pressure sensors need to match my model?

Yes. Tyre pressure monitoring sensors are matched to the model, build year and the radio frequency the vehicle expects, which is typically 433 megahertz on European Land Rover and Range Rover models. A sensor from the wrong generation may not pair with the vehicle, so confirm the correct type against your model and year before ordering.

Which wheel accessories are universal?

Balancing beads, valve caps and most valve hardware are not tied to a specific model, so they suit the range broadly. Centre caps, spacers, tyre pressure sensors and inner tubes are size or model dependent and should be matched to your wheel or vehicle.

Budget Parts. Land Rover and Range Rover wheel accessories, stocked in the Netherlands for EU dispatch.

Land Rover Wheel Accessories

Filters (1)

FRC4377 - Hub Cap

219098 - Drive Shaft Hub Cap

GA2232 - Spare wheel carrier - swing-away rear door

FRC4377LR - Hub Cap

GA2027 - Spare Wheel Cover – 235/85 R16

GA2021 - Spare Wheel Cover – 7.50x16 – Soft – Plain

MRC5627 - Spare Wheel Buffer – Bonnet

576844 - Wheel Hub Assembly – With Stud

FRC3875 - Wheel Hub Assembly

GA2022 - Spare Wheel Cover – 600 x 16

RRC5035 - Wheel Cap – LH

DA3000 - Inner Tube – 7.50 x 16 / 7.00 x 16 – Small Valve

593873 - Hub Cap

BA 042AH - Spare Wheel Cover – 205x16 – Hard

DA2026 - Wheel Cover 205 x 16

RRC5035LR - Finisher

GA3000 - Inner Tube – 7.50 x 16 / 7.00 x 16 – Small Valve

About Land Rover wheel accessories

What fits which wheel

Choosing the right part

Related categories

Frequently asked questions

Added to your cart: