Land Rover Wheel Bearings & Seals

Hub Cap closes the centre of the front hub drive flange, covering the driveshaft coupling bolts within the front axle hub assembly. This version c...

Hub Cap fits over the end of the front or rear hub, enclosing the drive flange and hub assembly. It closes off the outer end of the hub to retain ...

Crankshaft Oil Seal - Rear for the rear crankshaft oil sealing assembly of the 300 TDi engine. Seated in the rear crankshaft seal housing at the f...

Rear Crankshaft Oil Seal seated in the crankshaft rear oil seal housing at the back of the cylinder block, sealing the point where the crankshaft e...

Front Crankshaft Oil Seal seated in the engine front (timing) cover, sealing the crankshaft nose where it exits the crankcase. The seal runs again...

Oil Seal for the rear differential, part of the rear axle final drive assembly. It seals the rotating shaft where it exits the differential housin...

Snap Ring

Crankshaft Oil Seal - Rear seals the rear of the crankshaft where it leaves the cylinder block at the flywheel end, retaining oil within the bottom...

Oil Seal Retainer for the front axle. It retains the oil seal at the swivel pin bearing housing, holding the seal that runs against the halfshaft.

Bearing Holder - front bearing housing within the Front Axle Drive Shaft assembly. The holder carries and retains the front support bearing of the...

Wheel Hub and Bearing is a front wheel hub assembly with an integrated wheel bearing, operating within the front knuckle and hub group. The unit m...

Bearing Retainer - front bearing retainer within the Front Axle Drive Shaft assembly. The retainer secures and locates the front support bearing o...

Pinion Bearing Spacer sets the pinion bearing preload in the rear differential. Fitted on the drive pinion shaft between the pinion head and tail ...

Oil Seal - Front Axle Case - output seal in the front axle case and differential assembly. Seals the point where the drive output passes out of th...

Seal Kit renews the seals at the hydraulic pipe connections of the Active Cornering Enhancement (ACE) anti-roll bar system. The ACE system uses hy...

Seal - Oil Pump

Oil Seal for the LT230 transfer box input shaft. Part of the transfer box gear train. The seal fits around the rotating input shaft where it enter...

Oil Seal - Differential Flange - Front seals the front differential where the drive flange exits the axle case. It runs against the differential o...

Gearchange Lever Oil Seal seals the gearchange lever where it enters the manual gearbox housing. It retains transmission oil around the selector l...

Seal Kit - Torque Converter - 8-Speed Auto

Oil Seal for the transfer case input shaft. Seals the input shaft where it enters the transfer case, retaining lubricant and excluding contaminant...

Pinion Oil Seal sealing the drive pinion shaft where it enters the Salisbury rear differential. Fitted at the nose of the differential housing, th...

Wheel Hub with integrated wheel bearing, forming the wheel end of the front and rear suspension assembly. The hub carries the wheel mounting flang...

Front wheel hub with bearing, part of the front knuckle and hub assembly. The hub locates in the steering knuckle and carries the road wheel and b...

Front Wheel Hub - hub and integrated wheel bearing unit for the front knuckle assembly. The hub carries the road wheel and brake disc and is drive...

Front Wheel Knuckle, left-hand side - the suspension upright at the outer end of the front axle, part of the front hub and knuckle assembly. The k...

Front Wheel Knuckle, right-hand side - the suspension upright at the outer end of the front axle, part of the front hub and knuckle assembly. The ...

Front Wheel Knuckle, left-hand side - the suspension upright at the outer end of the front axle, part of the front hub and knuckle assembly. The k...

Front Wheel Knuckle - right-hand side. The steering knuckle of the front suspension and steering assembly. The knuckle carries the front wheel hub...

Wheel Hub is part of the wheel-end assembly at the suspension corner. It carries the wheel bearing and provides the mounting flange for the road w...

Snap Ring is a retaining ring that seats into a machined groove to locate a component on a shaft or within a bore, holding it against axial movement.

Watts Roller Bearing is the centre roller bearing of the rear Watt's linkage, the mechanism that locates the rear axle laterally. It forms the cen...

Seal kit NLA NLA NLA

Retainer Oil Seal On Output Housing

Rear Differential Oil Seal Kit - a set of oil seals for the rear differential and rear drive unit. The kit supplies the seals needed when resealin...

Drive Shaft Oil Seal - Front, fitted at the front axle swivel pin housing. This radial lip seal runs on the front driveshaft where it passes throu...

Oil Seal Retainer for the front axle swivel housing assembly. This retaining plate holds the swivel housing oil seal square against the chrome swiv...

Seal - Oil

Seal - Oil

Oil Seal

Oil Seal for the gearbox output shaft. This seal fits at the output shaft of the MT82 6-speed manual gearbox, sealing between the rotating output ...

Stub Axle Oil Seal - Inner

Hub Oil Seal - Inner for the front and rear wheel hubs, seating around the stub axle. The seal runs on the stub axle to retain hub lubricant and e...