for Discounts / VAT
for Discounts & Correct VAT
Replacement parts for the Land Rover Defender L663, the current-generation Defender produced from 2020 to present. Covers all three body variants in OEM, Genuine, and aftermarket quality.
For Classic Defender parts (pre-2016), see Land Rover Defender parts.
Bolt for the primary drive pulley and accessory drive belt assembly. Secures the crankshaft primary drive pulley on supercharged V6 petrol, V8 pet...
View full detailsLeak Detection Pump - DMTL (Diagnostic Module Tank Leakage) unit for the fuel tank evaporative emission (EVAP) system. The module sits between the...
View full detailsClimate Control Humidity Sensor, an input device for the automatic climate control system. Mounted at the base of the interior rear-view mirror, i...
View full detailsSupercharger Isolator - the torsional damping coupler inside the supercharger drive, sitting between the drive input and the rotor pack of the Root...
View full detailsO-Ring and Grease Kit for servicing the transfer box input shaft. Contains the input shaft O-ring and the anti-seize grease used when resealing th...
View full detailsO-Ring and Grease Kit for servicing the transfer box input shaft. Contains the input shaft O-ring and the anti-seize grease used when resealing th...
View full detailsCylinder Block Core Plug Seal sealing a core plug aperture in the cylinder block. It seals a casting core plug opening in the block, preventing co...
View full detailsCylinder Block Core Plug Seal sealing a core plug aperture in the cylinder block. It seals a casting core plug opening in the block, preventing co...
View full detailsWheel Nut Set - Satin Black - set of twenty wheel nuts in a satin black finish, sufficient for four five-stud road wheels. Each nut clamps the roa...
View full detailsElectronic Pressure Control Solenoid for the transfer case control circuit. The solenoid is actuated electrically by the vehicle's control module ...
View full detailsTransmission Oil Pan for the ZF 8HP eight-speed automatic transmission. It bolts to the underside of the transmission case and retains the automati...
View full detailsFront timing cover - the lower centre cover that closes the front face of the cylinder block over the timing chain drive. It carries the crankshaf...
View full detailsSupercharger Isolator - the torsional damping coupler inside the supercharger drive, sitting between the drive input and the rotor pack of the Root...
View full detailsWater Inlet Tube - rigid coolant connector within the engine cooling circuit, joining the thermostat housing to the upper coolant hose. It carries...
View full detailsTiming Chain Tensioner for the timing chain drive of the 5.0L V8 (AJ133) and 3.0L supercharged V6 petrol engines. It bears against the timing chain...
View full detailsDrive Belt Tensioner for the primary accessory drive at the front of the engine. The spring-loaded tensioner holds the correct tension on the belt ...
View full detailsTyre Pressure Sensor (TPMS) for the direct tyre pressure monitoring system. Fitted at the wheel valve inside the tyre, it measures tyre pressure an...
View full detailsOil Filter Housing Cover is the cover for the cartridge-type oil filter assembly on 3.0 GDI petrol and 5.0 AJ-V8 engines. This cover retains the r...
View full detailsTransmission Oil Pan and Filter for the ZF 8HP 8-speed automatic transmission (8HP45 and 8HP70, and the later 8HP51/8HP76 variants). The pan bolts...
View full detailsWater Pump for the engine cooling circuit, fitted to supercharged petrol applications (3.0L DOHC GDI supercharged V6 and 5.0L AJ133 DOHC supercharg...
View full detailsVariable Valve Timing Solenoid - oil control solenoid for the variable valve timing system. The solenoid regulates engine oil flow to the camshaft...
View full detailsBrake Vacuum Pump, the auxiliary vacuum source for the brake servo on petrol engines. Petrol engines - particularly direct-injection and superchar...
View full detailsFan Bracket carries the secondary drive belt idler pulley within the front end accessory drive of supercharged petrol engines. It locates the idle...
View full detailsBrake Vacuum Pump, the auxiliary vacuum source for the brake servo on petrol engines. Petrol engines - particularly direct-injection and superchar...
View full detailsFuel Pump - high-pressure, engine-mounted fuel injection pump within the direct-injection fuel system on petrol engines. Driven off the engine, it...
View full detailsFuel Pump - high-pressure, engine-mounted fuel injection pump within the direct-injection fuel system on petrol engines. Driven off the engine, it...
View full detailsFuel Pump - high-pressure, engine-mounted fuel injection pump within the direct-injection fuel system on petrol engines. Driven off the engine, it...
View full detailsCamshaft Sprocket is a timing drive gear in the valvetrain, mounted on the end of a camshaft. Driven by the timing chain from the crankshaft, it r...
View full detailsCamshaft Sprocket for the timing drive of the 3.0L V6 supercharged (AJ126) and 5.0L V8 supercharged (AJ133) petrol engines. Driven by the timing c...
View full detailsAlternator for the engine charging system. Driven by the auxiliary drive belt, it generates the electrical power that charges the battery and suppl...
View full detailsWinrace Alloy Wheel - 8x18 - Anthracite - 18" aluminium alloy road wheel in an anthracite finish. 8" rim width, ET42 offset, 5x120 PCD, 72.6 mm cen...
View full detailsWinrace Alloy Wheel - 8x18 - Black - 18" aluminium alloy road wheel in a black finish. 8" rim width, ET42 offset, 5x120 PCD, 72.6 mm centre bore, r...
View full detailsTiming Chain Kit for the timing drive of the AJ133 5.0L V8 petrol engine (naturally aspirated and supercharged) and the AJ126 3.0L V6 supercharged ...
View full detailsBattery - Wet Non-Spillable for the vehicle electrical system. It is a flooded (wet) lead-acid battery of sealed, non-spillable construction. It su...
View full detailsTransmission Oil Pan for the ZF 8HP eight-speed automatic transmission. It bolts to the underside of the transmission case and retains the automati...
View full detailsCompomotive Alloy Wheel 8" x 18" - Black
Compomotive Alloy Wheel 8" x 18" - Grey
Oil Pump for the engine lubrication system of the supercharged petrol V6 and V8 (AJ133) engines. Driven from the crankshaft, the oil pump draws oi...
View full detailsVacuum Pump supplying the brake servo on the supercharged AJ133 petrol engines (3.0L V6 and 5.0L V8). Forced-induction petrol engines cannot rely ...
View full detailsSpark Plug Well Gasket seals the spark plug aperture in the camshaft (valve) cover on the right-hand cylinder head bank. It prevents engine oil fr...
View full detailsBonnet Latch is the closure mechanism that engages the bonnet striker to hold the bonnet securely shut, releasing when the bonnet release is operat...
View full detailsBonnet Latch – left-hand (LH) side, part of the bonnet locking mechanism at the front of the vehicle. The latch engages the bonnet striker to hold...
View full detailsSensor Assembly
Sensor Assembly
Sensor Assembly
Spark Plug Gasket - LH seals the spark plug apertures in the left-hand cylinder head cover (cam cover). It keeps engine oil out of the spark plug w...
View full detailsExpansion Tank Cap seals the coolant expansion tank in the engine cooling system and sets the circuit's operating pressure. The pressure-relief va...
View full detailsCam Cover Gasket seals the right-bank camshaft cover to the cylinder head on the 5.0L V8 (AJ133) petrol engine. It forms the oil-tight joint aroun...
View full detailsThe Land Rover Defender L663 is the current-generation Defender, built on Land Rover's D7x aluminium unibody architecture and produced in Nitra, Slovakia from 2020 to present. It is available in three body configurations: the Defender 90 (3-door), the Defender 110 (5-door), and the Defender 130 (5-door extended, 8-seat). The L663 shares no body panels, drivetrain components, or structural parts with the Classic Defender (L316) that preceded it. Parts from the Classic Defender range do not fit the L663.
Reference note: official L663 technical specifications are available via the Land Rover Media Centre technical data archive.
Fitment NotesThe L663 is available with a range of petrol and diesel engines from the AJ200 and AJ300 Ingenium families, alongside a plug-in hybrid variant. The engine fitted to your vehicle determines which fuel system, cooling, ancillary, and filtration parts are compatible. Before ordering engine parts, confirm your engine variant from your VIN plate or vehicle registration document.
Petrol variants:
Diesel variants:
The P400e PHEV uses a high-voltage battery system and an additional electric motor alongside the combustion engine. Braking, cooling, and driveline components on P400e models differ from those on standard petrol and diesel variants. If your vehicle is a P400e, confirm the specific component requirement for your variant before selecting parts.
All L663 variants use a ZF 8-speed automatic transmission with a 2-speed transfer case providing permanent four-wheel drive.
Suspension FitmentThe Defender 110 and Defender 130 are fitted with air suspension as standard across all variants. The Defender 90 is available with either air suspension or coil springs depending on specification. Air suspension components and coil spring components are not interchangeable. Before ordering any suspension part for a Defender 90, confirm whether your vehicle has air or coil suspension. This information is available on your VIN plate and in your vehicle handbook.
Buying GuideParts in this collection are marked as OEM, Genuine, or Aftermarket. The distinction matters for fitment decisions and budget planning.
Genuine parts are produced by Land Rover or its authorised supply chain and carry the Land Rover part number. They are the closest match to factory specification.
OEM parts are produced by the same manufacturers that supply Land Rover's production line, but sold outside the Genuine parts programme. They meet the same manufacturing standards as Genuine parts in most cases and are typically priced lower.
Aftermarket parts are produced by independent manufacturers to fit the L663 platform. Quality varies by brand and application. For safety-critical systems including brakes, steering, and suspension, Budget Parts stocks aftermarket parts from established brands only.
If your vehicle is within a valid Land Rover warranty period, confirm with your dealer whether fitting aftermarket or OEM parts affects your warranty before ordering.
The L663 has been in production since 2020 and has received specification updates across model years. If you are ordering a part and are unsure whether it matches your build, your 17-digit VIN is the most reliable reference. The VIN is stamped on the door sill plate, the windscreen base, and the vehicle registration document. The VIN encodes your model year, engine variant, body style, and build market, which allows Budget Parts to confirm part compatibility before you order.
If you cannot find the part you need in this collection, use the backorder option. Budget Parts will source the part from its supplier network and notify you when it is ready to dispatch.
Technical GuidesThe following guides provide deeper technical context for Defender L663 ownership, service planning, and parts selection.
Known failure areas across the Defender range including L663 fitment considerations, common parts requirements by variant, and what EU owners and workshops should verify before ordering.
Defender parts Europe 2025 →The diagnostic process for overheating on Land Rover Ingenium engines, including the cooling system components most likely to require replacement. Relevant to L663 owners with D300 or P400 engines.
Land Rover overheating diagnosis →For component-specific browsing, the following category collections cover L663-compatible parts alongside other Land Rover models.
Brake discs, pads, callipers, and full brake system components for Defender L663 and the wider Land Rover range.
Land Rover brake parts →Air suspension and coil spring components, shock absorbers, bushes, and suspension fitting hardware.
Land Rover suspension parts →AJ200 and AJ300 Ingenium engine service parts, ancillaries, gaskets, and rebuild components.
Land Rover engine parts →Sensors, modules, wiring components, and electrical ancillaries for current-generation Defender models.
Land Rover electrical parts →No. The Defender L663 (2020 to present) is built on the D7x aluminium unibody platform and shares no structural, body, or drivetrain components with the Classic Defender (L316), which was produced from 1983 to 2016. Parts designed for Classic Defender models will not fit the L663. If you own a pre-2016 Defender, use the Classic Defender parts collection.
Yes, in some categories. The three body variants share the same D7x platform and powertrain options, but differ in wheelbase, body length, interior configuration, and in some cases suspension setup. The Defender 90 can be specified with either air suspension or coil springs, while the 110 and 130 come with air suspension as standard. Rear-end body parts, interior trim components, and some suspension parts are body-variant specific. Always confirm your body variant and build specification before ordering.
The most reliable method is your 17-digit VIN, which can be decoded to identify your engine variant, model year, and market specification. The VIN is located on the door sill plate, the base of the windscreen, and your vehicle registration document. Your vehicle handbook also lists the engine code on the specification page. For diesel models, the AJ200D (4-cylinder) and AJ300D (6-cylinder) engines have different service part requirements. For petrol models, the P400e PHEV has additional electric drivetrain components not present on the P300 or P400.
Genuine parts carry the Land Rover part number and are produced by Land Rover's authorised supply chain. OEM parts are produced by the same manufacturers that supply Land Rover's production line but sold outside the Genuine programme, typically at a lower price. Aftermarket parts are produced by independent manufacturers to fit the L663. For safety-critical components including brakes, suspension, and steering, Budget Parts stocks aftermarket parts from established brands. Each product listing on this page states its quality classification.
Yes. If a part is not currently in stock, the backorder option is available on the product listing. Budget Parts will source the part from its supplier network and contact you with an update once the part is located and ready. This covers both OEM and Genuine parts that may have longer lead times due to supply chain availability.
Yes, in certain categories. The P400e uses a 2.0-litre AJ200 petrol engine combined with a high-voltage electric motor and a 13.1 kWh battery system. Components related to the braking system (which includes regenerative braking), high-voltage battery cooling, and the electric drivetrain are specific to the P400e and differ from those on the standard P300 and P400 petrol variants. If your vehicle is a P400e, confirm the exact component specification with Budget Parts before ordering parts in these categories.
Updated: 6 May 2026