Land Rover Defender New Parts

Sealing Ring sealing a joint within the engine timing gear covers. This O-ring seals a connection at the timing cover assembly, maintaining oil-ti...

Cover Gasket for the upper timing chain cover. It seals the joint between the upper timing chain cover and the engine, maintaining an oil-tight se...

Valve Stem Seal for the cylinder head valvetrain. It seals around the valve stem where it passes through the valve guide, controlling oil entry in...

Timing Chain Guide for the engine timing gear. It supports and locates the timing chain along its run, controlling the chain path and reducing vib...

Timing Chain Guide for the engine timing gear. It supports and locates the timing chain along its run, controlling the chain path and reducing vib...

Timing Chain Tensioner Arm for the engine timing gear. It bears against the timing chain and transmits the tensioner load to take up slack and mai...

Special Bolt for the engine timing gear assembly. It secures a component within the timing gear drive. Fitted to 2.0-litre diesel Ingenium engines...

Idler Pulley for the accessory drive belt system, 65 mm in diameter. It guides the accessory (auxiliary) drive belt across its run, maintaining be...

Bolt securing the fuel injector and high-pressure fuel pipe assembly on the engine fuel system. It clamps the injector and high-pressure pipe unio...

Water Outlet Tube forming the coolant outlet connection at the cylinder head, part of the engine cooling circuit. It carries coolant from the cyli...

O-Ring for the turbocharger of the 2.0L I4 diesel (AJ200) engine, sealing the upper turbocharger-to-pipe joint (14.3 x 2.4 mm). The O-ring seals t...

O-Ring sealing a turbocharger oil and coolant connection within the turbocharger lubrication and cooling circuit. It seals the union at the turboc...

Oil Drain Plug for the engine oil pan (sump). Threaded into the base of the oil pan, it seals the oil drain point and is removed to drain the engi...

Cylinder Head Bolt with hex head, for the 2.0L I4 diesel (AJ200) engine. The bolt secures the cylinder head to the engine block, providing the cla...

Turbocharger Gasket for the exhaust turbocharger assembly on the 2.0L I4 diesel (AJ200) engine, sealing the turbocharger outlet to the exhaust fron...

Screw - M6 x 65mm threaded fastener. Factory-specified fixing screw with a 6mm (M6) thread and 65mm length.

Insulator - Bush Type

Chain Lubricating Jet is an oil spray jet in the timing drive of the 3.0L V6 supercharged and 5.0L V8 petrol engines. Installed behind the front c...

Differential Mounting Washer used in the front differential mounting arrangement. The washer is fitted at a front differential mounting point, spr...

O-Ring seals a connection joint in the front air conditioning refrigerant circuit. It maintains the pressure-tight seal between refrigerant lines o...

Brake Fluid for the hydraulic braking and clutch actuation system, supplied in a 1 litre container. A DOT 4 low-viscosity (ESL) fluid formulated f...

Clip retaining the top of the rear air spring within the rear spring and shock absorber assembly. The clip locates and secures the air spring at i...

Timing Chain Guide - guides the primary timing chain along its run. Maintains correct alignment and tension on the primary timing drive, keeping c...

Timing Chain Guide - guides the timing chain along its run. Maintains correct alignment and tension on the timing drive, keeping crankshaft-to-cam...

Thermostat Tube carries engine coolant between the thermostat housing and the engine on the supercharged 3.0L V6 and 5.0L V8 petrol engines. It run...

O-Ring seal for the automatic transmission oil cooler circuit (ZF 8-speed, 8HP). The O-ring seals a connection in the transmission fluid cooling c...

Throttle Housing Gasket - seals the throttle body to the intake manifold. Forms the air-tight joint between the electronic throttle housing and th...

Hex Head Bolt and Washer - a hexagon-head bolt supplied with a washer. A general-purpose fixing used at multiple mounting locations, including the...

Coolant Hose - throttle body heater outlet hose within the engine cooling circuit. The hose routes engine coolant from the throttle body heater ou...

Idler Pulley - a drive belt idler in the front-end accessory drive (serpentine belt) system. The idler pulley routes and guides the multi-rib driv...

Degas Hose for the engine cooling system's degassing circuit. The hose routes coolant and entrained air from the engine and radiator to the degas (...

Fuel Injector Refit Kit - the seals and retainer required when removing and refitting a fuel injector on 3.0L V6 and 5.0L V8 supercharged petrol en...

Coolant Hose carries engine coolant through the cooling circuit, connecting the components that circulate coolant to and from the engine. Moulded ...

Flanged Nut for the front suspension arm mountings. The integral flange spreads the clamp load across the joint face and helps the nut resist loos...

Exhaust Manifold Bolt secures the exhaust manifold to the cylinder head. For 3.0L supercharged V6 and 5.0L V8 petrol applications.

Water Outlet Tube carries coolant between the water pump and the thermostat housing within the engine cooling circuit. For 3.0L supercharged V6 an...

Brake Caliper Mounting Bolt for the front brake assembly, securing the caliper to its mounting on the hub carrier. This high-tensile fastener is t...

Retaining Clip - a push-fit fastener used to secure exterior and interior trim mouldings and finishers to the body. The clip pushes into a locatin...

Auxiliary Drive Chain for the AJ133 5.0L V8 and 3.0L V6 supercharged petrol engines. It forms part of the engine's chain drive assembly, running a...

Sealing Ring seals the joint between the engine oil cooler and the water pump on the AJ133 5.0L V8 and 3.0L supercharged V6 petrol engines. It mai...