Land Rover Defender New Parts

PCV Valve Service Kit

PCV Valve Service Kit - service parts for the positive crankcase ventilation valve, which sits in the crankcase emission control system on the cyli...

Turbocharger Coolant Hose from the engine cooling circuit, serving the turbocharger on the 3.0L AJ20P6 petrol engine. The hose carries engine cool...

Coolant Tube forming the primary coolant path between the cylinder block and the water outlet. This aluminium tube carries coolant from the engine...

Timing Chain Guide locates and supports the timing chain within the timing drive assembly. It maintains correct chain alignment along its run, con...

Connector - Valve Block to Pipe for the air suspension system. This fitting joins the air suspension valve block to the air line, forming the seal...

Timing Chain Guide locates and supports the timing chain within the timing drive assembly. It maintains correct chain alignment along its run, con...

Cup Holder - an interior trim component fitted to the floor (centre) console. It provides a moulded holder to retain cups or containers within the...

Insulator is a rubber bush fitted in the front suspension, within the front cross member and stabiliser bar assembly. It locates and cushions the ...

Sealing Washer is the fuel injector sealing washer for the Ingenium diesel engine (2.0L and 3.0L AJ20 / AJ21 diesel). It seats at the base of the ...

Front Crankshaft Oil Seal located at the front of the cylinder block, on the crankshaft. Seals the crankshaft where it exits the front of the engi...

Valve Spring Seat is the seat on the cylinder head that locates the base of the valve spring, providing the surface against which the spring is com...

Exhaust Clamp secures a joint between two sections of the exhaust system, clamping the adjoining pipes together to form a gas-tight connection whil...

Valve Stem Seal for the cylinder head valvetrain. It seals around the valve stem where it passes through the valve guide, controlling oil entry in...

Oil Drain Plug for the engine oil pan (sump). Threaded into the base of the oil pan, it seals the oil drain point and is removed to drain the engi...

Wheel Centre Cap for the alloy road wheel. This cover fits to the hub centre of the alloy wheel, closing off the centre bore and completing the wh...

Screw - M6 x 65mm threaded fastener. Factory-specified fixing screw with a 6mm (M6) thread and 65mm length.

Insulator - Bush Type

Chain Lubricating Jet is an oil spray jet in the timing drive of the 3.0L V6 supercharged and 5.0L V8 petrol engines. Installed behind the front c...

Differential Mounting Washer used in the front differential mounting arrangement. The washer is fitted at a front differential mounting point, spr...

Brake Fluid for the hydraulic braking and clutch actuation system, supplied in a 1 litre container. A DOT 4 low-viscosity (ESL) fluid formulated f...

Clip retaining the top of the rear air spring within the rear spring and shock absorber assembly. The clip locates and secures the air spring at i...

Timing Chain Guide - guides the primary timing chain along its run. Maintains correct alignment and tension on the primary timing drive, keeping c...

Timing Chain Guide - guides the timing chain along its run. Maintains correct alignment and tension on the timing drive, keeping crankshaft-to-cam...

Thermostat Tube carries engine coolant between the thermostat housing and the engine on the supercharged 3.0L V6 and 5.0L V8 petrol engines. It run...

O-Ring seal for the automatic transmission oil cooler circuit (ZF 8-speed, 8HP). The O-ring seals a connection in the transmission fluid cooling c...

Throttle Housing Gasket - seals the throttle body to the intake manifold. Forms the air-tight joint between the electronic throttle housing and th...

Hex Head Bolt and Washer - a hexagon-head bolt supplied with a washer. A general-purpose fixing used at multiple mounting locations, including the...

Coolant Hose - throttle body heater outlet hose within the engine cooling circuit. The hose routes engine coolant from the throttle body heater ou...

Idler Pulley - a drive belt idler in the front-end accessory drive (serpentine belt) system. The idler pulley routes and guides the multi-rib driv...

Degas Hose for the engine cooling system's degassing circuit. The hose routes coolant and entrained air from the engine and radiator to the degas (...

Fuel Injector Refit Kit - the seals and retainer required when removing and refitting a fuel injector on 3.0L V6 and 5.0L V8 supercharged petrol en...

Coolant Hose carries engine coolant through the cooling circuit, connecting the components that circulate coolant to and from the engine. Moulded ...

Flanged Nut for the front suspension arm mountings. The integral flange spreads the clamp load across the joint face and helps the nut resist loos...

Exhaust Manifold Bolt secures the exhaust manifold to the cylinder head. For 3.0L supercharged V6 and 5.0L V8 petrol applications.

Water Outlet Tube carries coolant between the water pump and the thermostat housing within the engine cooling circuit. For 3.0L supercharged V6 an...

Brake Caliper Mounting Bolt for the front brake assembly, securing the caliper to its mounting on the hub carrier. This high-tensile fastener is t...

Timing Chain Lubricating Oil Jet for the timing drive of the 5.0L V8 petrol engine (AJ133, naturally aspirated and supercharged). The jet feeds pr...