Land Rover Defender New Parts

Wheel Centre Cap - a black alloy-wheel centre cap carrying the Land Rover oval in green and silver. It presses into the centre bore of an alloy wh...

Cable Grommet for the wiring loom, fitting a 41.5 mm panel hole and accepting a cable of up to 6 mm. Made of black rubber, it lines the hole where...

Handbrake cover LHD

Bolt and Washer - an M8 x 24mm bolt supplied with a washer, used as a general-purpose fixing across several Land Rover assemblies. The washer spre...

Grommet / Blanking Plug - Dash Bulkhead for Land Rover Defender. This rubber plug seals an unused aperture in the dash bulkhead (such as a heater ...

Shock Absorber Washer Retaining washer for the rear shock absorber lower mounting. Part of the rear suspension assembly, it locates over the lower...

EGR Cooler Filter for the low-pressure exhaust gas recirculation circuit of the 2.0L I4 Ingenium diesel engine. The low-pressure EGR system draws ...

Magnetic Oil Drain Plug for the engine oil sump on the 2.0L Ingenium (AJ200/AJ20) four-cylinder petrol and diesel engines. The plug seals the drai...

Oil Filter Gasket Kit for the engine oil filtration circuit of the 2.0L Ingenium (AJ200) engine, renewed with the oil filter element at each servic...

Wiper Blade for the rear window wiper assembly of the New Defender (L663). This blade uses the Aquablade design: washer fluid is channelled throug...

Wiper Blade for the front windscreen wiper assembly of the New Defender (L663, 2020 onwards). Fits the front wiper system on the Defender 90, Defe...

Coolant Temperature Sensor in the engine cooling circuit. This sensor monitors coolant temperature and transmits a signal to the engine management...

Cover Gasket for the crankcase cover, part of the emission-control and crankcase ventilation system on the 2.0L AJ200 four-cylinder diesel engine. ...

Thermostat Seal for the thermostat housing on AJ200/AJ20 series petrol and diesel engines. It seals the thermostat housing joint within the cooling...

Oil Cooler Gasket seals the oil cooler within the oil cooler and filter housing assembly. It maintains the oil-tight joint between the cooler and ...

Idler Pulley for the front-end accessory belt drive, 90mm diameter. The idler routes and guides the auxiliary drive belt around the accessory pull...

Injector Refit Kit supplying the seals needed to refit a fuel injector on petrol engines. It restores the sealing interface between the injector an...

Accessory Drive Belt - multi-rib belt driving the engine's front-end accessories. Transmits crankshaft rotation to the belt-driven ancillaries wit...

Brake Pad Wear Wire - front brake pad wear warning wire within the braking system. Routed to the front brake pad, the wire completes a circuit tha...

Timing Chain Tensioner Arm bears against the timing chain within the timing drive assembly, providing the face through which the tensioner applies ...

Hex Head Bolt - M14 x 148mm fastener used at the front crossmember and stabiliser bar, front suspension arm, rear bumper and tow bar mountings. A ...

Axle oil filler plug, sealing the combined fill and level aperture in the axle casing. Used at both front and rear axle positions. The plug closes...

Axle oil drain plug, sealing the drain aperture at the base of the axle casing. Used at both front and rear axle positions. The plug is removed to...

Gearbox Plug

Secondary Accessory Drive Belt - the supercharger drive belt within the front end accessory drive of the supercharged petrol V6 and V8 engines. Me...

Primary Accessory Drive Belt for the 5.0L AJ133 DOHC supercharged V8 petrol engine, forming part of the front end accessory drive. The multi-ribbe...

Blanking Plug - timing chain cover, supplied with its O-ring. Seals a machined service aperture in the timing chain cover of the Ingenium engine f...

Interior fixing screw used throughout the instrument panel, floor console and interior trim assemblies. It secures trim panels, mounting brackets ...

Connecting Tube running from the thermostat housing to the EGR cooler, part of the engine coolant circuit on the 2.0L Ingenium petrol engine and it...

Bolt for the camshaft timing gear, part of the Ingenium engine timing drive. It retains the timing sprocket to the camshaft, transferring drive fr...

Coolant Vent Hose - connects the engine vent elbow to the radiator, within the vent (bleed) circuit of the engine cooling system. The hose carries...

Timing Chain Guide - LH Primary - a fixed guide in the timing drive assembly of the 2.0L four-cylinder Ingenium petrol engine (AJ200 / AJ20P4), inc...

Antifreeze and Coolant Concentrate - red, extended-life engine coolant concentrate for the cooling system, supplied in a 1 litre container. The fl...

Arm - Timing Chain Tensioner