Price <10

Accelerator Rod in the throttle linkage. This rigid rod transmits accelerator pedal movement through the linkage to operate the engine throttle.

Crankshaft Sensor Spacer for the Land Rover Td5 2.5-litre 5-cylinder turbo diesel engine in manual transmission applications. This spacer fits bet...

Hose Clip for securing flexible hoses to pipes and stubs throughout the Land Rover. Tightening the clip compresses the hose onto the stub to form a...

Rocker Shaft Locating Bolt for the 2.25L and 2.5L petrol, 2.5L naturally aspirated diesel and 2.5L turbo diesel engines, securing the rocker shaft ...

Heater Control Pin

Mainshaft Nut - castellated nut that retains the assembled components on the rear of the gearbox mainshaft. The castellations accept a split pin to...

Centre Retainer - Front Windscreen Glass is the metal retainer strip that secures the front windscreen glass at its centre division point. The ret...

Torx Screw - 4.8 × 25mm for use in Land Rover body and trim assemblies. A metric Torx-head screw, 4.8mm diameter × 25mm length, for use where Torx...

Sealing Washer is a copper joint washer used in multiple engine and ancillary applications across the Land Rover range, including as a sealing wash...

Exhaust U-Bolt secures a joint in the front section of the exhaust system. The U-bolt clamps over the pipe at a slip joint and, tightened against i...

Nut Plate for the rear side door and sill panel assemblies. It provides captive threaded anchor points for the door hinge and check strap fixings,...

Heater Controls Spacer - spacer fitted within the heater control assembly of the HVAC unit. Sold individually.

Dial Illumination Bulb - the backlight bulb and bulbholder assembly for the LCD climate control panel, part of the heating and ventilation controls...

Pedal Clutch Bearing

Oil Filter Gasket for the four-cylinder 2.25L/2.5L petrol and 2.5L naturally aspirated diesel engines, part of the engine lubrication circuit. The...

Cap Reservoir Br.m.cylinder

Clevis pin

Flywheel Dowel is a locating dowel that registers the flywheel to the crankshaft rear flange. Pressed into the crankshaft flange, it sets the angu...

Exhaust Manifold Bolt for the Rover V8 petrol engine, threaded 3/8" UNC and 1 1/8" long. The bolt secures the exhaust manifold to the cylinder hea...

Bolt - M12 × 160 mm hex-head bolt used as a chassis and suspension fixing. It secures suspension radius arms and links, the top link fulcrum and ba...

Torsion Spring Sleeve for the lower tailgate. It fits over the tailgate torsion spring, forming a protective bearing sleeve at the pivot and preven...

Filler Strip is the fixing channel that runs along the top edge of the rear door window aperture. It locates and retains the upper edge of the doo...

Cylinder Head Dowel - Plastic is a locating pin fitted at the mating face between the cylinder block and cylinder head in the Td5 2.5L 5-cylinder t...

Brake pipe clip

Blanking Plug - a push-fit plug used to close an unused aperture in a body panel, door or interior trim component. It seals the opening against wa...

Propshaft Lock Washer, used within the propshaft and viscous coupling assembly. The lock washer is seated beneath the retaining fastener at the pr...

Brake Pipe Clip - Rear secures the rear brake pipes on the Discovery 2, holding the hydraulic lines in place along the chassis. The clip prevents ...

Clevis Pin for the differential lock selector linkage in the LT230 transfer gearbox. This clevis pin secures the selector lever pivot that actuate...

Fastener - black plastic drive-type (fir tree) push-in fastener used throughout the vehicle to secure body trim panels, interior linings, underbonn...

Detent Spring for the LT77 and R380 manual gearbox gear change mechanism. This spring forms part of the selector detent assembly within the gearbo...

Plate

Trim Clip is an interior trim fixing that retains the A-pillar trim panel against the body structure. Depending on application it also serves as t...

Cable Tie for securing wiring looms and cables in Land Rover applications.

Screw - No.10 x 1" Pan head, self-tapping, pointed fastener used in door trim and window regulator assemblies. It secures the interior grab handle...

Spire Nut, a J-type sheet-metal spring nut (also known as a speed nut) used to secure trim, panels and fittings. The nut clips over a panel edge o...

Shock Absorber Washer Retaining washer for the rear shock absorber lower mounting. Part of the rear suspension assembly, it locates over the lower...

Clutch Cap that closes an aperture in the clutch bellhousing around the release mechanism. Fitted over an opening in the bellhousing, the cap seal...

P-Clip - 19/64" x 3/8" is a pressed-steel P-profile retaining clip used to route and secure fuel lines, brake pipes, or wiring looms against a chas...

Clip - 13/64" x 3/8" is a single-bolt retaining clip used to secure wiring harnesses, vacuum lines, and small-bore hoses to body or engine bay brac...

Fuel Tank Mounting Washer is used at the fuel tank mounting points, spreading the clamping load of the fixing across the mounting bracket or strap....

Washer

Swivel Pin Retaining Bolt A fixing bolt for the front axle swivel pin housing. It secures a swivel pin to the swivel pin housing, retaining the pi...

Seal Washer - Turbocharger Copper sealing washer for the turbocharger oil feed circuit. It seals the banjo union on the turbocharger's oil supply ...

Torque Converter Housing Cover Gasket for the automatic transmission bell housing. It seals the lower access cover on the torque converter housing...

Instrument Bulb Holder Assembly is a 1.4W instrument panel bulb supplied complete with its integrated holder, forming part of the instrument cluste...

Manifold Stud - a mounting stud that secures the exhaust manifold to the cylinder head. It threads into the cylinder-head casting and projects thr...

Locking Nut A locking nut for the gear lever plunger in the gearchange mechanism of the 5-speed manual gearbox. It retains the spring-loaded plung...

Core Plug - Cylinder Block Expansion Port is a pressed-steel sealing plug installed in the outer face of the cylinder block to close the casting ap...