Price <10

Brake Pipe Union for the hydraulic brake system, a female fitting in brass. This union connects a 3/16 inch brake pipe into the brake hydraulic ci...

Oil Filter Housing Gasket for the Td5 2.5L five-cylinder turbo diesel engine, sealing the oil filter housing/adaptor to the cylinder block. It sea...

Oil Cooler Pipe O-Ring for engine and transmission oil cooling circuits. This O-ring seals pipe fitting and hose connection joints in the oil cool...

Sump Drain Plug Washer - sealing washer for the engine sump drain plug on the Td5 2.5L 5-cylinder turbo diesel engine. This washer seats between t...

Bolt, M10 x 45 securing the front drive member to the hub. The drive member transmits torque from the axle shaft to the road wheel, and these bolts...

Oil Filler Plug serving as the combined fill and level check point for the swivel pin housing, manual gearbox gearcase, and LT230 transfer box on L...

Pinion Oil Seal sealing the drive pinion shaft where it enters the Salisbury rear differential. Fitted at the nose of the differential housing, th...

Rocker Cover Gasket for the 2.5L 200TDi diesel engine, sealing the joint between the rocker cover and the cylinder head. Installed at the top of t...

Suspension and Chassis Mounting Bolt used across multiple suspension and chassis linkage positions. This hexagon bolt secures components including...

Split Pin for use in the front and rear suspension assembly of the Series Land Rover. The split pin is inserted through the hole in a castle nut o...

Rear Reflector, self-adhesive, measuring 9 cm x 3 cm, part of the rear lighting and signalling assembly. A passive retroreflector that returns inc...

Hub Outer Oil Seal for the front and rear wheel hub assemblies. Located at the outer end of the hub, it retains the wheel-bearing grease within the...

Bolt - fixing bolt with an ACME (trapezoidal) thread form, used to secure the outer front wing to the bulkhead. It fastens the rear mounting flang...

Distributor Rotor Arm for the 3.5L V8 petrol ignition system. The rotor arm sits on top of the distributor shaft beneath the cap and rotates to dis...

Flanged Nut is a hexagonal nut with an integrated flange at its base. The flange spreads clamping load across a wider bearing surface, removing the...

Sealing Washer used at sealing interfaces across multiple engine assembly groups. This washer is used in rocker cover and breather assemblies, val...

Transfer Box Output Shaft Felt Seal for the Series II and Series III LT15 transfer box. The waxed felt seal fits around the rear output shaft and ...

Fuel Tank Top Gasket sealing the sender, pump or pick-up unit against the top face of the fuel tank. A flat sealing gasket fitted at the tank-top ...

Anti-Roll Bar Washer used at the anti-roll bar and shock absorber mounting. The washer spreads the clamping load of the retaining nut across the m...

Windscreen Hinge Gasket - Upper - Small

Cable Clip for securing the body wiring harness, part of the vehicle electrical system. This clip retains a cable run against the body or chassis,...

Radius Arm Bolt - hexagon head bolt securing the rear radius arm at the axle and chassis mounting points within the rear suspension assembly. This...

Oil Seal installed within the wheel hub assembly to retain lubricant and prevent contamination ingress at the hub-to-stub-axle interface. The seal...

Fuel Filter for the diesel fuel delivery system, separating dirt, debris and water from the fuel before it reaches the injection pump. Fitted in t...

Flanged Screw, M8 x 25 mm. A metric set screw with an integral flange beneath the hexagon head that spreads clamping load and helps resist loosenin...

O-Ring for the LT230 Transfer Box, used at multiple sealing positions within the unit. This O-ring is fitted at several locations in the LT230 two...

Door Hinge Bolt for attaching door hinges to the body structure. This countersunk bolt secures the hinge plate to the hinge assembly, providing a ...

Copper Sealing Washer used across a wide range of sealing applications on Land Rover vehicles. This soft copper washer provides a reliable, leak-f...

Injector O-Ring for the 2.5L Td5 5-Cylinder Turbo Diesel fuel injection system. This O-ring seats in the groove on the injector body at the cylind...

CuNiFer Brake Pipe, 3/16" outer diameter, supplied for the brake hydraulic circuit. The copper-nickel alloy resists corrosion and is soft enough to...

filter fuel inline Series petrol engines. Used as air filter in vacuum control lines for EGR in: - L322 3.0 M57 DSL (BMW) - Freelander1 M47 16V 2.0...

Self-Locking Nut with a 5/16" UNF thread and a 1/2" across-flats hexagon. The self-locking action resists loosening under vibration, retaining cla...

Hex Nut - 1/4" UNF is a plain hexagonal nut with a 1/4 inch UNF thread, used as a general-purpose imperial-thread fastener throughout the chassis, ...

Brake pad kit rear

Spark Plug - ignites the air/fuel mixture in the combustion chamber of the petrol engine. It threads into the cylinder head with its electrode gap ...

Captive Nut with a UNF thread, providing a fixed threaded anchor point for a bolted fixing. The nut is retained in its bracket or panel so it cann...

EP2 Grease multipurpose extreme-pressure lubricant for automotive applications. NLGI Grade 2 consistency provides the right balance of pumpability...

Felt Washer for the output shaft assemblies of the LT230 transfer box. This washer is fitted at the front and rear output flanges of the LT230, wh...

Inlet Manifold Seal for the V8 petrol induction system, straight pattern. The seal closes the joint between the underside of the inlet manifold an...

Fitment: All models to (VIN) KA930455 All models 1980 on

Brake Union for the hydraulic braking circuit, with male 7/16"-20 UNF thread for 1/4" diameter brake pipe. This male-threaded end fitting connects...

Bolt - a threaded fastener used within the rear axle and suspension assembly. It secures the rear knuckle and suspension arm mountings, clamping e...

Copper Sealing Washer for banjo bolt connections in the engine oil circuit. This copper washer seats against the machined face of a banjo fitting ...

Door Casing Trim Clip is a fir-tree push-fit fastener used in the interior door trim assembly to retain the door casing panel against the door fram...

Propshaft Bolt Kit - Rear is a driveline fixing set for securing the rear propeller shaft at its flange connections. The kit provides the correct-...

Washer Non-Return Valve for the windscreen wash/wipe system. The valve is fitted into the washer fluid line between the pump and the jets. It perm...

Nut - a plain full hex nut with a 3/8" BSF (British Standard Fine) thread. A general-purpose imperial fastener used at many points across the engi...

Exhaust Mounting Rubber - flexible support that suspends the silencer section of the exhaust system from the vehicle underbody. The moulded rubber...