Range Rover Classic Parts

Rear Crankshaft Packing Strip (T-Piece) forms part of the rear crankshaft oil seal arrangement at the back of the cylinder block. The T-piece pack...

Injection Pump Gasket seals the fuel injection pump to its mounting face on the timing case of the 200Tdi and 300Tdi 2.5L turbo diesel engines. Th...

Filler Plug sealing the fill and bleed point of the engine cooling system, fitted to the thermostat housing and the radiator. This plastic plug cl...

A/C Drive Belt drives the air-conditioning compressor on the 2.5L 300TDi diesel. Run from the crankshaft pulley, it transmits drive to the air-con...

Flywheel Housing Gasket for the 200 TDi diesel engine, sealing the joint between the flywheel (or drive plate) housing and the rear face of the cra...

Tow Ball Step is a rear access step that locates over the tow ball, providing two tread levels to make reaching the rear door, load area or roof ea...

Bolt with a 5/16" UNF (Unified National Fine) imperial thread and a 1-1/2" shank length. A hex-head fastener for general assembly and fixing appli...

Bolt 1/4" UNF x 2" is a hex-head set bolt with a 1/4-inch Unified National Fine (UNF) thread at 28 threads per inch and a 2-inch shank length. It ...

Bolt - Bracket to Chassis is an M10 x 60 mm fastener that secures a bracket to the vehicle chassis frame. It has a 10 mm nominal thread diameter a...

Alternator 300TDi (with pulley)

Ignition Coil for the V8 petrol ignition system. It converts the low-voltage supply into the high-tension voltage that fires the spark plugs throug...

O-Ring for the speedometer drive spindle on the LT230 transfer gearbox. Seals the spindle housing where the speedometer drive take-off enters the ...

Track Rod & Steering Damper Bush for the steering linkage, locating the steering damper at its mounting eye. The bush insulates the damper mou...

Oil Filler Cap O-Ring seals the oil filler cap to the rocker cover. It forms an oil-tight seal at the cap-to-cover joint, preventing oil leakage a...

Fuel Pipe Olive for the fuel supply line. The olive is the compression ferrule that seats between the fuel pipe and its union fitting. When the un...

O-Ring for the engine sump, part of the engine lubrication sealing arrangement. Seals the sump joint to prevent oil leakage. Fitted to four-cylind...

Rubber Plug Cushion is a moulded rubber blanking plug that fits into a pre-formed aperture in the body, frame or seat base to close off the opening...

Cable Grommet for the wiring loom, fitting a 41.5 mm panel hole and accepting a cable of up to 6 mm. Made of black rubber, it lines the hole where...

Alternator for the engine charging circuit, of the Lucas A127 type rated at 45A output. Driven by the auxiliary drive belt from the crankshaft pul...

Glass Fuse - 25A - a 25 A glass cartridge fuse for the vehicle's electrical circuits. The glass body carries a calibrated wire element between two...

Wheel Centre Cap in a Silver Sparkle finish with the embossed Land Rover logo, fitting the centre bore of the alloy road wheel. It conceals the hub...

Gearbox Mounting - right-hand transmission rubber mounting for the 2.5L 300 TDi diesel. This rubber-to-metal mounting supports the gearbox on the ...

Countersunk Screw - a machine screw with a flat, cone-shaped head that seats flush with the surface it fixes, leaving no proud edge. Metric M6 thr...

Cooling Fan for the 2.5L 300 TDi turbo diesel engine, forming part of the engine cooling assembly. The fan is driven from the front of the engine ...

Exhaust mounting spacer tube

Aerial with cable Defender

Water Temperature Sensor (coolant temperature transducer) that threads into the thermostat housing within the engine cooling circuit. The transduc...

Banjo Bolt (6mm) for the fuel injector leak-off return circuit on the 200TDi and 300TDi 2.5L turbo diesel engines. The hollow bolt clamps the inje...

Accelerator Cable in the throttle control linkage, connecting the accelerator pedal to the fuel injection pump. It transmits pedal movement to the...

Steering box sector shaft seal kit for the steering system. This kit contains the sealing components required for the sector shaft assembly withi...

Front Propshaft This propshaft transmits drive from the transfer box output to the front axle differential, forming part of the four-wheel-drive d...

Distributor Module for the 3.5L Rover V8 petrol engine, used with the earlier single-coil electronic ignition system. It forms part of the distribu...

Fuel Filler Cap that seals the fuel tank filler neck. Non-locking type with a black finish, closing the filler neck against fuel vapour loss and t...

Core Plug for the rear of the camshaft bore in the V8 petrol cylinder block. The cup-type plug seals the machined opening at the rear of the camsh...

Differential Guard for the axle differential, protecting the diff housing and cover from impact damage off-road. Clamps over the differential cent...

Propshaft UJ Circlip - a retaining clip for the universal joint of the propeller shaft. It seats in the groove of the yoke ear and holds the beari...

Sedimentor Seal for the diesel fuel sedimentor assembly. The sedimentor separates water and sediment from the fuel ahead of the injection system. ...

Steel ball 1/4"

Carburettor Gasket - a sealing gasket for the Zenith-Stromberg 175CD carburettor as fitted to the 3.5 litre V8. It seals a joint within the carbur...

Wheel spacer kit fitted between the wheel hub and road wheel within the wheel mounting assembly. The spacers move the wheel mounting face outward...

Distributor Lead for the ignition system of the 3.5L V8 petrol engine. This lead connects the distributor to the ignition amplifier module, adapti...

Air Filter element for the air cleaner housing on the induction system. The element traps dust and airborne particles from the incoming air before...

Crankshaft Thrust Washer Pair for the 4-cylinder engine, including the 200 TDi and 300 TDi diesels. The thrust washers sit either side of the centr...

Primary Pinion Bearing for the manual gearbox, supporting the primary pinion (gearbox input shaft). The primary pinion transmits drive from the cl...

Plain Washer - flat washer for use in general fastening assemblies throughout the vehicle. Distributes load and protects mating surfaces under bol...

Sealing Washer seals the engine oil sump drain plug, fitting between the drain plug head and the sump drain boss. When the drain plug is tightened...

30mm alloy wheel spacer set designed to position the wheel further outward from the hub assembly. The spacers are manufactured from alloy and supp...

Rear suspension shock absorber designed to control vertical movement of the axle and dampen spring oscillation within the suspension system. This...