Range Rover Classic Parts

Ball Joint Service Tool for the steering drop-arm ball joint. The tool presses the drop-arm ball joint (part RBG000010) into and out of the drop a...

Hexagon Bolt - an M10 x 45 mm high-tensile bolt, property class 10.9, used in the suspension top link, fulcrum and ball joint assembly. The 10.9 g...

Radius Arm Bolt with a 5/8" UNF (Unified National Fine) imperial thread and a 3-1/2" shank length. Secures the front radius arm to its axle or cha...

Alternator assembly within the engine charging system, installed on the front-end accessory drive and driven by the auxiliary belt to convert mecha...

Brake Caliper is the front left-hand hydraulic caliper in the front disc brake assembly. It houses the pistons that press the brake pads against t...

Brake Caliper is the front right-hand hydraulic caliper in the front disc brake assembly. It houses the pistons that press the brake pads against ...

Oil Pump Relief Plunger is the pressure-relief valve plunger within the engine oil pump, part of the lubrication system on the 3.5L V8 petrol engin...

Oil Pump Gear for the 3.5L V8 engine oil pump, part of the lubrication system. The oil pump draws oil from the sump and pressurises it for deliver...

Clutch Lever Clip that retains the clutch release lever on its pivot post within the gearbox bellhousing. The clip holds the release fork onto the...

Differential Pinion Inner Taper Roller Bearing used in the differential pinion shaft assembly within the axle final drive. The bearing supports th...

Thermostat for the 2.5L 300TDi diesel engine, operating within the thermostat housing at the top of the cooling circuit. The thermostat regulates ...

Flame Trap is the crankcase breather filter fitted in the rocker cover breather circuit of the V8 EFI petrol engine. Connected in the crankcase ve...

Power Steering Pipe for the power-assisted steering hydraulic circuit, carrying pressurised fluid between the steering pump and the steering box. ...

Headlamp Wash T-Piece - three-way T-connector in the headlamp washer fluid line. Splits the feed hose from the washer pump so a single supply serv...

Breather Hose for the crankcase ventilation system on the 2.5L diesel and 200TDi turbo diesel engine. This flexible hose carries crankcase blow-by...

Turbo Oil Drain Pipe for the 300 TDi engine, returning lubricating oil from the turbocharger to the sump. Connects the turbocharger bearing housin...

Engine Push Rod for diesel engine valve actuation, operating within the cylinder head valve train. The push rod transmits motion from the camshaft...

Gear Lever Grommet for the 5-speed manual gearchange assembly. It seals around the gear lever where it passes through the housing, sealing out dra...

Radiator with Integrated Oil Cooler - the main engine cooling radiator for the 200 TDi diesel engine, incorporating a built-in engine oil cooler an...

Exhaust Tailpipe forms the rearmost section of the exhaust system, carrying exhaust gas from the intermediate silencer to the rear of the vehicle a...

Speedo cable

Headlamp Bezel - stainless steel, 7". The trim ring that surrounds the 7" round headlamp, retaining the lamp unit in the front panel and finishing ...

Blanking Plug for closing an unused 16 mm (5/8") hole in body or trim panelling. A push-in plastic plug used to blank off redundant or open apertu...

Clutch release fork is used in the clutch release mechanism of manual transmission systems. The fork operates within the clutch housing and conve...

Fuel Pipe Union Nut for the fuel delivery line. This female threaded nut draws a fuel pipe up to its mating union, clamping the pipe's flared or c...

Plenum Chamber Hose Hose within the V8 EFI induction system, running from the plenum chamber to the starter motor housing. It connects the plenum ...

Screw 1/4" UNF x 1" screw used as a fixing in the upper section of the rear tailgate assembly.

Plug Washer for the drain and filler/level plugs on the LT95 gearbox and differential. The washer seats between the threaded plug and the casing t...

Steering Box Seal Kit reseals the input shaft of the 4-bolt power steering box within the power-assisted steering circuit. The input shaft is wher...

Steering Arm Fixing Kit for the heavy-duty steering arms DA5503 and DA5504. It supplies the fixings needed to mount the heavy-duty steering arms i...

Steering Box Output Oil Seal for the manual, non-power-assisted steering box. It seals the output (rocker) shaft where it exits the steering box h...

Oil Gallery Plug for the cylinder block oil gallery on Land Rover 4-cylinder engines. The oil gallery is the network of internal drillings in the ...

Shock Absorber Washer - Rear - a retaining washer used at the rear suspension shock absorber mounting. It seats against the lower shock absorber b...

Bracket tie bar for steering box

Self-Tapping Screw - a No. 8 x 3/8" self-tapping screw used as a general-purpose fixing. The self-tapping thread cuts its own mating thread as it ...

Spring Washer, 5/16" - a single-coil split washer fitted under a nut or bolt head to maintain clamp tension. The split coil acts as a spring, exer...

Exhaust U-Bolt - a U-bolt clamp used to secure a joint in the exhaust system. It retains the exhaust front pipe (downpipe) connection, clamping th...

Shock Absorber Washer Retaining washer for the rear shock absorber lower mounting. Part of the rear suspension assembly, it locates over the lower...

Thin Nut - a reduced-height hex nut with a 5/16" UNF (Unified Fine) thread. The shallow profile suits fastening points with limited clearance and ...

Bolt - M8 x 100mm hex head bolt used in the transmission mounting assembly. Secures transmission mounting components on Series III vehicles equipp...

Tailgate Seal for the rear end structure. This seal fits around the tailgate aperture, sealing the joint between the tailgate and the rear body to...

Front Brake Caliper is the left-hand front caliper of the disc braking system, for the vented-disc setup. It clamps the brake pads against the fro...

Front Brake Caliper is the right-hand front caliper of the disc braking system, for the vented-disc setup. It clamps the brake pads against the fr...

Window Motor - LH for the front door electric window regulator system on the Range Rover Classic and Discovery 1. This is the left-hand motor unit...

Steering Shaft Assembly forming the intermediate link between the steering column and the steering box. The shaft transmits rotation from the stee...

Radius Arm Bush Set - polyurethane bushes for the front radius arm mountings at the axle end of the arm, supplied as a set of four in black. The b...

Wheel Nut for alloy wheel fitment on Defender, Discovery 1 and Range Rover Classic. This tapered-seat wheel nut is designed for use with alloy whe...

Tank Mounting Spacer - a spacer used in the fuel tank mounting assembly. It sets the correct standoff between the tank and its supporting bracketr...