Range Rover Classic Parts

Exhaust Tailpipe forms the rearmost section of the exhaust system, carrying exhaust gas from the intermediate silencer to the rear of the vehicle a...

Brake Master Cylinder Repair Kit for the Range Rover Classic hydraulic braking system. This rebuild kit contains the seals and components required...

Panhard Rod Bolt with a 1/2" UNF (Unified National Fine) imperial thread and a 3-1/4" shank length, manufactured to a high-tensile grade. Secures ...

Front Radius Arm Bush (rubber) located at the chassis end of the front radius arm. The bush is pressed into the radius arm mounting eye where the ...

Rear Main Bearing Cap Seal for the Rover V8 petrol engine, sealing the joint between the rear main bearing cap and the cylinder block. This crucif...

Engine Mounting Rubber (V8) supports the V8 petrol engine on the chassis and isolates its vibration from the bodyshell. The bonded rubber-to-metal...

Track Rod End Assembly for the steering linkage, connecting the track rod to the steering drop arm and transmitting movement from the steering box ...

Drive Screw - a No. 6 x 1/2" self-tapping drive screw used across door and facia assemblies. It secures the front door glass and window regulator,...

Bottom cover seal

Clutch release fork is used in the clutch release mechanism of manual transmission systems. The fork operates within the clutch housing and conve...

Engine Service Filter Kit for the 3.5L and 3.9L Rover V8 EFI engine, covering the consumable filtration elements renewed at a routine engine servic...

Gasket kit 300tdi lower block set no rear crankshaft seal

Taper Roller Bearing - shaft bearing for the R380 five-speed manual gearbox. A taper roller bearing carries both radial load and axial thrust, loc...

Coolant Hose - Expansion Tank Vent is the bleed hose in the engine cooling system, connecting the radiator bleed outlet to the coolant expansion ta...

Engine mounting

Radius Arm Bush mounts at the axle end of the front radius arm, within the front suspension radius arm and axle location assembly. It forms the co...

Radius Arm Bush - Front is the flexible mounting bush at the front radius arm-to-chassis location. The radius arm locates the front axle longitudi...

Plenum Chamber Hose Hose within the V8 EFI induction system, running from the plenum chamber to the starter motor housing. It connects the plenum ...

Spring Retaining Plate Front coil spring retaining plate that clamps over the top of the spring at its seat, holding the spring captive so it canno...

Regulator Pressure Fuel 3.5V8 - EFI

Steering Box Seal Kit reseals the input shaft of the 4-bolt power steering box within the power-assisted steering circuit. The input shaft is wher...

Wheel Hub Stud FRC5926 or RUF000020 for Defender 90 And 110, Discovery I and Range Rover Classic.

Designed for use with heavy-duty steering arms, this kit provides the necessary brackets and hardware for a solid fitment, enhancing steering stabi...

Steering Box Output Oil Seal for the manual, non-power-assisted steering box. It seals the output (rocker) shaft where it exits the steering box h...

Windscreen Filler Strip closes and trims the gap between the windscreen glass and the body aperture, forming part of the windscreen sealing and fin...

Banjo Bolt for the fuel and oil circuits, used to secure a banjo union to its housing while allowing fluid to pass through the cross-drilled body. ...

Oil Pump Lock Tab, part of the engine oil pump assembly. The lock tab is a tab washer fitted under the oil pump retaining fastener; once the faste...

Sump Plug for the engine oil sump (oil pan), part of the engine lubrication system. It threads into the drain hole at the base of the sump to seal...

Half Shaft Shim - 0.90mm is a 0.90mm selective shim that fits on the outside of the axle driving member to set the endfloat of the half shaft withi...

Bolt M8 X 16 HTSETS 8.8 S/COL sold EACH

Half Shaft Shim - 0.60mm is a 0.60mm selective shim used to set the endfloat of the axle half shaft within the hub assembly. It is fitted at the d...

Window Lift Switch is the control switch within the electric window circuit. Fitted to the door trim or centre console, it directs current to the ...

Front Axle Shim, 0.45mm thick. Fitted to the front axle half-shaft assembly to set the correct end-float, taking up clearance so the shaft is posit...

Shock Absorber Washer Retaining washer for the rear shock absorber lower mounting. Part of the rear suspension assembly, it locates over the lower...

Bolt is an M8 x 80 mm threaded fastener used to clamp two components together at a bolted joint. It is tightened into a threaded hole or secured w...

Nut - M8 plain low-profile nut, sold individually. A standard metric M8 nut in the low-profile (thin) form. Used across gearbox, suspension, axle,...

Fulcrum Bracket for the rear suspension A-frame assembly. The bracket provides the chassis mounting point for the A-frame ball joint, which locate...

Fuel Tank Bracket for securing the fuel tank to the vehicle chassis. This metal bracket forms part of the fuel tank mounting assembly, locating an...

CV Joint Circlip - the retaining circlip that secures the constant velocity (CV) joint to the front drive shaft. The circlip locates in a groove o...

Front Mud Flap Kit, supplied as a left and right pair. Mounts behind the front wheel arches to reduce spray, mud, and stone throw from the front w...

Kickdown Cable Assembly for the automatic transmission control. The cable links the throttle to the automatic gearbox, relaying throttle position s...

Steering Lever - RHD for the Adwest power steering box, supplied with the ball joint fitted. Also known as the drop arm, the lever clamps onto the...

Power Steering Hose - Steering Box to Reservoir - Left-Hand Drive for the Range Rover Classic and Discovery 1 hydraulic steering circuit. This hos...

Steering Shaft Assembly forming the intermediate link between the steering column and the steering box. The shaft transmits rotation from the stee...

Fuel Pump Seal for the fuel tank sender unit. This seal seats at the mounting flange of the fuel pump and sender unit where it interfaces with the ...

Front Brake Hose forms the flexible section of the front braking hydraulic circuit, carrying pressurised brake fluid from the fixed chassis brake p...

Glazing Seal - the glazing rubber that lines the front door window channel and cushions the glass within it. It grips the edge of the glass, holds ...

Swivel Pin Housing Oil Seal for the front axle swivel and stub axle assembly. This is the outer seal, fitted at the interface between the stub axle...