Range Rover Classic Parts

Upper Oil Cooler Pipe - feed pipe in the engine oil cooling circuit of the 4.0L V8 EFI petrol engine, carrying oil from the engine to the oil coole...

Plain Washer - metric M8 plain washer for use in general fastening assemblies throughout the vehicle. A standard flat washer used to distribute lo...

Body Rivet - a mechanical fastener used within the body and panel assembly to join thin sheet metal, trim and stowage fittings. Nominal size 3/16"...

Hose Clip - 12-20mm worm-drive hose clip suitable for hoses with an outside diameter of 12 to 20mm. This stainless-steel screw-type clip tightens ...

Shock Absorber Bush Set for the shock absorber mountings. This set provides the bushes that locate each shock absorber at its mounting eyes, insul...

Track Rod End Boot Ring - spring retaining ring for the track rod end of the steering linkage. It clamps the rubber dust boot onto the track rod en...

Cooling Fan for the engine cooling assembly. Driven from the front of the engine through the viscous fan coupling, the fan draws air through the r...

Banjo Bolt is a hollow union bolt used in the fuel system of the 200 Tdi and 300 Tdi engines. It secures a banjo hose fitting at the injection pum...

Filler Plug in blue anodised aluminium, replacing the standard cooling system filler and blanking plug at the thermostat housing. Seals against a ...

Rocker Shaft for the 300 TDi engine, mounted in the cylinder head valvetrain. Carries and locates the rocker arms above the valves, providing the ...

Clutch Hose for the 300 Tdi 2.5L turbo diesel, forming the flexible section of the clutch hydraulic actuation circuit. The hose links the rigid pi...

Towing Socket Plate for the trailer towing electrics. This mounting plate carries the trailer electrical socket at the rear of the vehicle, provid...

Tappet Slide for Land Rover 4-cylinder engines, covering the Series I, Series II, Series IIA, and Series III (2.0L Diesel and 2.25L Petrol and Dies...

Oil Feed Pipe - Turbo supplies pressurised engine oil to the turbocharger in the 300 Tdi lubrication circuit. It carries oil from the cylinder blo...

EGR Valve to Pipe Gasket for the diesel exhaust gas recirculation (EGR) system. The gasket seals the flanged joint between the EGR valve and the r...

Camshaft Bearing Set for the Rover V8 petrol engine. This set provides the bearing surfaces on which the camshaft journals run within the cylinder...

Heater Blower Motor & Fan assembly for the cabin heating and ventilation system. The motor drives the fan that draws air through the heater box...

Accelerator Cable - throttle cable for TDi diesel applications. It connects the accelerator pedal to the injection pump throttle lever, transmitti...

Tensioner Pulley for the air conditioning drive belt on the 2.5L 300TDi turbo diesel engine. It runs against the accessory drive belt and maintain...

Cylinder Head Gasket Kit for the 2.4L and 2.5L VM diesel engine, covering the ancillary sealing components required during cylinder head removal an...

Number Plate Lamp is the rear registration plate light within the exterior lighting system. Mounted above the rear number plate, it illuminates th...

Radiator Hose is the bottom (lower) coolant hose in the engine cooling system, connecting the radiator outlet to the water pump inlet. It carries ...

Polyurethane bushes

Flexible Steering Shaft Coupling located in the steering column intermediate shaft, joining the steering column to the steering box input. The fle...

Panhard bush RR >'85

Banjo bolt

Ignition Module & Link Lead - a kit for the 3.5L Rover V8 petrol engine ignition system, comprising the electronic ignition module (amplifier) ...

Differential Assembly - a reconditioned 4-pin differential unit for the Land Rover-type axle. The differential sits at the centre of the axle, tak...

Double Cardan Joint Kit for the Discovery 2 front propshaft. The Discovery 2 front propshaft uses a double cardan joint assembly incorporating thr...

Brake Caliper Piston Kit - replacement pistons for the rear brake caliper. The pistons run in the caliper bores and, under hydraulic pressure, pre...

Heavy Duty spring Range Rover rear +0mm

Crankcase Breather Hose forms part of the closed crankcase ventilation circuit, connecting the rocker cover breather outlet to the intake manifold ...

The cable forms the mechanical link between the handbrake operating lever and the handbrake mechanism within the handbrake assembly, transmitting l...

Flange Bolt - M8 x 130mm, used to secure the coolant pump (water pump) on the 2.5L 300 TDi diesel engine. The integrated flange beneath the head s...

Rear Propshaft Coupling Kit - a flexible rubber coupling that connects the rear propeller shaft to the drive flange, transmitting drive while absor...

Coolant Expansion Tank with a clear (translucent) body, part of the engine cooling system. The tank serves as the system's pressurised reservoir a...

Steering Column Lock - the steering column lock and ignition switch assembly. Mounted on the steering column, it mechanically locks the column whe...

Piston Ring Set supplies the sealing rings for one piston of the 3.5L V8 petrol engine, in standard (non-oversize) bore size. The rings seal the p...

Radiator Hose - Bottom - V8 Petrol

Bottle sensor

Clutch Driven Plate for the V8 clutch assembly. It is carried on the gearbox input shaft between the flywheel and the clutch cover (pressure plate)...

Exhaust Bracket supports and locates a section of the exhaust system against the underbody. It carries the weight of the exhaust at its mounting p...

thrust collar, bush for stub axle - RRclassic upto (VIN) HA610293, - 101" Forward Control.

Alloy Wheel is a single-piece 16 x 7-inch alloy road wheel finished in black. It has a five-stud 5x165 mm bolt pattern and an ET20 offset, which s...

Steering Box Oil Seal Oil seal for the input (worm) shaft of the manual, non-power (Gemmer) steering box, sealing around the shaft where it enters ...

Gasket kit carburettor Zenith Stromberg 175CD

Gearbox Side Cover Gasket for the LT95 4-speed V8 gearbox. This gasket seals the side cover to the gearbox casing, preventing oil leaks from the ge...

Flange Bolt is an M8 x 35 mm bolt with an integral flange beneath the head. The flange spreads clamp load across the joint face and acts as a buil...