Range Rover Classic Parts

Shock Absorber - Rear for Range Rover Classic models fitted with rear air suspension. This hydraulic damper controls rear axle body movement and w...

Cylinder Head Gasket Set for the 2.5L 200TDi turbo diesel engine, supplying the top-end gaskets and seals required when the cylinder head is remove...

Conrod Bearing Kit - 0.010" Undersize for Land Rover four-cylinder petrol and diesel engines. Supplies a complete set of connecting rod big-end bea...

Radius Arm Bush mounts the front radius arm to the axle within the suspension linkage, at the axle end of the arm. The bush provides a flexible pi...

Rear Fuel Tank Assembly is the main fuel storage vessel of the fuel system, mounted at the rear of the vehicle. It holds the fuel supply and feeds...

Steering lock

Receiver Dryer for the air conditioning system, compatible with R134a refrigerant. Installed on the high-pressure side of the A/C circuit, between...

Intercooler Hose for the 2.5L 300TDi 4-cylinder turbo diesel engine on EGR-equipped variants. This rubber hose connects the intercooler to the int...

Steering Valve Ring is a PTFE sealing ring used within the rotary valve of the Adwest power steering box. It seals between the pressure lands of t...

O-Ring - Oil Pick-Up Pipe for the 2.5L 300TDi 4-cylinder turbo diesel engine. This O-ring seals the oil pick-up pipe connection at the oil pump or...

Joint Washer - LT77 Front Cover seals the mating face between the front cover and the main casing of the LT77 5-speed manual gearbox. The washer p...

Rocker Cover Breather Hose - Left-Hand for the crankcase ventilation system of the Rover 3.5L V8 twin-carburettor engine. This hose connects the l...

seal washer for block coolant drain plug. - All 4-cylinder engines upto 1998 (except VM diesel)

Rocker Arm for the rocker shaft valvetrain assembly of the Rover V8 petrol engine. The rocker arm pivots on the rocker shaft and transmits the lif...

Front Coil Spring, part of the front coil-sprung suspension. The spring fits between the chassis spring seat and the front axle, supporting vehicl...

Rocker Arm - Steel - LH for the valve train of the Rover V8 engine, part of the Cylinder Head & Valve Train assembly. This steel rocker arm pi...

Fuel Pump Adaptor for mounting the external fuel pump on petrol engines. It provides the interface between the external fuel pump and its mounting...

Windscreen Filler Strip closes and trims the gap between the windscreen glass and the body aperture, forming part of the windscreen sealing and fin...

Rocker Shaft Clamp for the cylinder head valve train on the 300TDi 2.5L turbo diesel engine. Secures the rocker shaft to the cylinder head pedesta...

Gear Lever Damper for the LT95 four-speed gearbox gear-change mechanism. This damping washer fits at the base of the main gear lever, absorbing vi...

Gear Lever Bias Plate for the manual gearbox gear change mechanism. It sits in the gear lever remote housing and works with the bias spring to load...

Left-Hand Rear Bumper Bracket that secures the rear bumper assembly to the body structure on the Range Rover Classic. This bracket is for the left...

Switch window lift

Gearbox Mainshaft Oil Seal, fitted where the mainshaft passes through the gearbox casing on the 5-speed manual transmission. It runs against the r...

Exhaust Mounting supports the rear section of the exhaust system, suspending it from the underbody. This rubber mounting locates the rear of the t...

Distributor O-Ring, the sealing ring for the ignition distributor on the 3.5L V8 petrol engine. The O-ring seals the distributor base where it loc...

Drain Plug - Coolant - Cylinder Block is the threaded plug that seals the coolant drain port in the cylinder block, providing a controlled drain po...

Pan Head Screw, M4 x 12mm. Metric pan head screw for use across a range of Land Rover assemblies, including brake system and electrical components.

Front Coil Spring - front suspension coil spring, seated between the axle spring pad and the chassis spring turret to support the vehicle and contr...

Fuel Sedimentor is a water and sediment trap in the diesel fuel supply line, installed upstream of the fuel filter and injection pump. Fuel passes...

Steering Stop Bolt - M12 x 50mm shouldered hex-head bolt for the front axle steering lock assembly. This bolt sets the maximum steering lock angle...

Cable Tie, Panel Fixing: grey cable tie strap with a panel fixing, 4.6 x 165 mm.

clamp exhaust pipe RRclassic (with twin exhaust pipes)

Fuse rated at 15A for the vehicle electrical system. Fitted in the fusebox to protect a circuit rated at 15 amps, the fuse breaks the connection w...

Sump Plug for the engine oil sump drain. Fitted to the sump drain port and removed at each oil change to drain the engine oil. The sealing washer ...

Viscous Fan Assembly for the engine cooling system, mounting to the viscous coupling unit on the front of the engine. This 16", 7-blade white fan ...

Winch Remote Control operates an electric recovery winch wirelessly, allowing the operator to stand clear of the winch line during recovery. Wirel...

Fitment: All non ABS models (VIN) JA032851 on to (axle) 38L03120B. 39L05552B. 42L00521B. 43L18579B All Models From (A)57L00001B To (A)57L05188B0

Air Spring - Front - pneumatic suspension bellows unit for the front axle of the Range Rover Classic Electronic Air Suspension (EAS) system. The a...

Bump Stop limits suspension travel within the suspension assembly, cushioning the contact between the axle and chassis at the extremes of wheel mov...

Upper Link Bush Set - Polyurethane for the rear suspension, fitted within the top link, fulcrum and ball joint assembly. Supplied as a set of two ...

Windscreen Seal is a rubber glazing seal fitted around the windscreen aperture. It retains the windscreen glass in the body aperture and seals the...

Heater Hose for the 200TDi engine cooling and heating circuit. This hose routes coolant from the engine cooling system to the cabin heater matrix,...

Heater Inlet Hose is a moulded coolant hose in the cabin heater circuit of the 200TDi 2.5L turbo diesel engine. It carries hot coolant from the en...

Gearbox Gaiter Grommet seals the point where the high/low transfer lever passes through its gaiter on the LT95 four-speed gearbox. Fitted to the t...

Clutch Damper for 200TDi and 300TDi diesel engines. This in-line hydraulic damper fits within the clutch hydraulic hose run between the master cyl...

Injector Pipe - No.4 is a rigid high-pressure fuel line in the injection circuit of the 2.5L 300 TDi turbo diesel engine. It carries metered fuel ...

Alternator of the Lucas A133 type, rated at 85A, for V8 EFI petrol engines. Driven by the auxiliary belt from the crankshaft as part of the engine...