Range Rover Classic Parts

Rear Wheel Bearing Kit containing the parts needed to overhaul one rear hub bearing assembly on ABS-equipped vehicles. The taper roller bearings ca...

Mounting Bracket, Front Spoiler. Left-hand bracket from the front spoiler and engine under tray assembly. It secures the front spoiler to the fron...

Oil Strainer for the LT77 and R380 five-speed manual gearboxes, located in the rear extension case. Filters the gearbox oil drawn by the internal ...

Front Mud Shield for the LT230 transfer box. Fits at the transfer box front output flange, shielding the output shaft oil seal from mud and debris...

Thrust Washer for the front axle swivel pin housing. The washer sits at the swivel pin bearing to set end-float and carry thrust loads within the ...

Drive Plate (flexplate) couples the V8 petrol engine crankshaft to the automatic transmission torque converter. The drive plate bolts to the rear ...

Camber Bush Set for the front radius arms, 38mm wide. The bushes locate in the front radius arm mountings and set the caster and camber geometry o...

Coil Spring is a light-duty rear suspension coil spring that raises ride height by approximately 40mm over standard. The light-duty rate suits a s...

Seat Base Trim Set that covers the lower seat base frame, supplied as a matched left- and right-hand pair (391525 LH and 391524 RH).

Steel Ball - 9/32 inch steel ball used in the steering column assembly. Supplied individually. Ball diameter 9/32 inch (7.14 mm).

Front Drive Flange Spacer for the LT230 transfer box. Fits on the transfer box front output shaft behind the drive flange, setting the correct sha...

Valve Guide for the cylinder head valve train of the Rover V8 petrol engine. The guide is an interference fit in the cylinder head and locates the...

V Belt Accessory drive belt for the 2.4L four-cylinder VM turbo diesel engine. Transmits drive from the crankshaft pulley to the alternator and wa...

Engine Lifting Bracket for the front of the 2.5L 200 TDi and 300 TDi diesel engines. The bracket bolts to the engine and provides a rated lifting ...

Front Radius Arm Bump Stop is a travel stop mounted at the front radius arm within the front suspension. It limits axle-to-chassis travel and cush...

Flexible Clutch Pipe forms part of the clutch hydraulic circuit, connecting the rigid pipework to the clutch slave cylinder. The flexible section ...

Fuel Tank Pump Sealing Ring for the fuel tank pickup and pump assembly. Seals the pump/pickup unit where it mounts to the top of the fuel tank, pr...

Oil Cooler Pipe connecting the oil cooler to the engine in the oil cooler circuit. It returns engine oil from the cooler to the engine. Used on 2....

Exhaust Pipe the intermediate section of the exhaust system. It links the front downpipe to the rear silencer and tailpipe, carrying exhaust gas a...

Cylinder Head Gasket for the 300 TDi 2.5L four-cylinder turbo diesel engine. It seals the joint between the cylinder head and the engine block, co...

Inlet Valve Stem Seal for the cylinder head valve train on the V8 petrol engine. The seal fits over the inlet valve guide and wipes the valve stem...

Injection Pump Support Bracket for the fuel injection system on the 2.5L 300 TDi turbo diesel engine. The bracket ties the injection pump to the e...

Coolant Bypass Bracket for the 2.5L 300 TDi turbocharged diesel engine, mounted at the coolant pump. Supports and locates the coolant bypass hose ...

Fuel Injection Pump Plate for the 2.5L 300 TDi turbocharged diesel engine, a component of the ERR5057 mechanical injection pump within the diesel f...

Use BA 2332A

Front Anti-Roll Bar in the front suspension assembly. It links the left- and right-hand suspension sides to resist body roll during cornering, imp...

Electronic Ignition Kit for the Rover V8 petrol engine with a points-type distributor. The kit replaces the mechanical contact points and condenser...

Steel Wheel - 16 x 6.5 is a pressed-steel tubeless road wheel finished in black. Technical data: Size: 16 x 6.5 PCD: 5 x 165.1 mm Offset: ET20 ...

UJ Fitting Kit

Caliper Repair Kit for overhauling the front brake callipers. The kit contains stainless steel replacement pistons, the calliper seal repair kit an...

EGR Blanking Kit closes off the exhaust gas recirculation (EGR) circuit on the 300 TDi diesel engine. The standard EGR valve feeds a portion of ex...

Rear Exhaust Silencer for the 200/300 TDi diesel exhaust system. It forms the rearmost section of the exhaust, attenuating gas-flow noise before t...

Rear Coil Springs supplied as a pair, giving a raised ride height of +50mm at a medium-duty spring rate. The springs lift the rear of the vehicle ...

Automatic Transmission Oil Cooler for the 300 TDi diesel engine paired with the ZF 4-speed automatic gearbox. Sits in the transmission cooling cir...

Britpart Coil Springs - Rear - Heavy Load - +2" Lift - Defender 90/Disco 1/Disco 2/RRC

Heavy Duty Drive Member Kit - Defender - Discovery 1 - RRC

Rear Floor Crossmember, a transverse structural member beneath the rear load floor. This crossmember runs across the underside of the body and sup...

Steering Shaft with universal joint, part of the steering column assembly. The shaft transmits rotation from the steering column to the steering bo...

Clutch Kit for the 200 TDi and 300 TDi diesel engines, uprated to a heavy-duty specification. The clutch transmits drive from the engine to the ge...

Clutch Kit for the 200 TDi and 300 TDi diesel engines, uprated to a heavy-duty specification. The clutch transmits drive from the engine to the ge...

Laminated Windscreen, green tinted, for the windscreen and glazing assembly. The screen is of laminated construction: two glass layers bonded to a...

Swivel Kit - complete swivel housing overhaul kit for one side of the front axle. The swivel housing ball carries the stub axle and encloses the c...

Suspension Kit - a standard ride-height, heavy-duty coil spring and shock absorber set covering both the front and rear axles. The kit contains he...

Swivel Kit - overhaul kit for one front swivel housing assembly. The swivel housing is the steering pivot at the outer end of the front axle case: ...

Distributor for the 3.9L V8 EFI petrol engine ignition system. Driven from the camshaft, it routes high-tension voltage from the ignition coil to ...